Basic ABS @BASIC

Unknown · ABS · by super-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

*common*

→

Basic ABS @BASIC

Settings

Basic information

Material variant: ABS overridden
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.04 overridden
was 0 (inherited)
Cost (/kg): 20 overridden
was 0 (inherited)

Print temperature

Nozzle (initial layer) (°C): 250 overridden
Nozzle (other layers) (°C): 240 overridden

Cooling

Fan maximum (%): 0 overridden
Disable fan for first N layers: 3 overridden
Full fan if layer below (sec): 20 overridden
Slow down if layer below (sec): 20 inherited
Min speed when slowed (mm/s): 15 inherited

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 11 overridden

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
High Temp Plate	100 overridden	90 overridden

Other settings

bridge fan speed: 30 overridden
cooling: 1 inherited
default fan speed: 0 overridden
fan always on: 0 overridden
filament colour: #3A80CA overridden
filament cooling final speed: 3.4 inherited
filament cooling initial speed: 2.2 inherited
filament cooling moves: 4 inherited
filament load time: 0 inherited
filament loading speed: 28 inherited
filament loading speed start: 3 inherited
filament minimal purge on wipe tower: 15 inherited
filament ramming parameters: 120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 overridden
was 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 (inherited)
filament soluble: 0 inherited
filament toolchange delay: 0 inherited
filament unload time: 0 inherited
filament unloading speed: 90 inherited
filament unloading speed start: 100 inherited

Raw resolved JSON

{
  "cooling": [
    "1"
  ],
  "filament_cost": [
    "20"
  ],
  "filament_notes": [
    ""
  ],
  "filament_density": [
    "1.04"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "end_filament_gcode": [
    ""
  ],
  "filament_load_time": [
    "0"
  ],
  "compatible_printers": [
    ""
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_unload_time": [
    "0"
  ],
  "slow_down_layer_time": [
    "20"
  ],
  "start_filament_gcode": [
    ""
  ],
  "filament_cooling_moves": [
    "4"
  ],
  "filament_loading_speed": [
    "28"
  ],
  "filament_unloading_speed": [
    "90"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "filament_ramming_parameters": [
    "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "filament_cooling_final_speed": [
    "3.4"
  ],
  "filament_loading_speed_start": [
    "3"
  ],
  "compatible_printers_condition": [
    ""
  ],
  "filament_cooling_initial_speed": [
    "2.2"
  ],
  "filament_unloading_speed_start": [
    "100"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "fan_always_on": [
    "0"
  ],
  "fan_max_speed": [
    "0"
  ],
  "filament_type": [
    "ABS"
  ],
  "hot_plate_temp": [
    "90"
  ],
  "filament_colour": [
    "#3A80CA"
  ],
  "bridge_fan_speed": [
    "30"
  ],
  "default_fan_speed": [
    "0"
  ],
  "nozzle_temperature": [
    "240"
  ],
  "fan_cooling_layer_time": [
    "20"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "hot_plate_temp_initial_layer": [
    "100"
  ],
  "filament_max_volumetric_speed": [
    "11"
  ],
  "nozzle_temperature_initial_layer": [
    "250"
  ],
  "name": "Basic ABS @BASIC",
  "type": "filament"
}

Version history

View full history with diffs →

v1 created 2026-05-19 13:23