Artillery PLA Tough

Artillery · PLA TOUGH · by anycubic-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pla

→

Artillery Generic PLA

→

Artillery PLA Tough

Compatible printers (4)

Artillery Sidewinder X3 Plus 0.4 nozzle
Artillery Sidewinder X3 Pro 0.4 nozzle
Artillery Sidewinder X4 Plus 0.4 nozzle
Artillery Sidewinder X4 Pro 0.4 nozzle

Settings

Basic information

Material variant: PLA Tough overridden
was PLA (inherited)
Vendor: Artillery overridden
was Generic (inherited)
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.24 inherited
Cost (/kg): 30 inherited

Print temperature

Nozzle (initial layer) (°C): 220 overridden
was 200 (inherited)
Nozzle (other layers) (°C): 220 overridden
was 200 (inherited)

Cooling

Fan minimum (%): 60 overridden
was 100 (inherited)
Fan maximum (%): 80 overridden
was 100 (inherited)
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 80 overridden
was 100 (inherited)
Slow down if layer below (sec): 8 overridden
was 8 (inherited)
Min speed when slowed (mm/s): 5 inherited

Flow

Flow ratio: 0.98 inherited
Max volumetric speed (mm³/s): 21 overridden
was 12 (inherited)

Retraction

Retraction length (mm): 1.3 overridden
was nil (inherited)
Retraction speed (mm/s): 40 overridden
was nil (inherited)
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	50 inherited	50 inherited
Engineering Plate	50 inherited	50 inherited
High Temp Plate	65 overridden was 60	65 overridden was 60
Textured PEI Plate	50 inherited	50 inherited

Other settings

additional cooling fan speed: 0 inherited
bed type: Cool Plate inherited
compatible printers: Artillery Sidewinder X3 Pro 0.4 nozzle, Artillery Sidewinder X3 Plus 0.4 nozzle, Artillery Sidewinder X4 Pro 0.4 nozzle, Artillery Sidewinder X4 Plus 0.4 nozzle overridden
was Artillery Sidewinder X1 0.4 nozzle, Artillery Genius 0.4 nozzle, Artillery Sidewinder X2 0.4 nozzle, Artillery Genius Pro 0.4 nozzle, Artillery Hornet 0.4 nozzle (inherited)
enable pressure advance: 1 overridden
filament id: GFL99 inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: 0.4 overridden
was nil (inherited)
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was true (inherited)
nozzle temperature range high: 230 inherited
nozzle temperature range low: 190 inherited
overhang fan speed: 100 inherited
overhang fan threshold: 50% inherited
pressure advance: 0.046 overridden
reduce fan stop start freq: 1 inherited
setting id: GFSA04 inherited
slow down for layer cooling: 1 inherited
temperature vitrification: 190 overridden
was 60 (inherited)

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "80"
  ],
  "fan_min_speed": [
    "60"
  ],
  "filament_cost": [
    "30"
  ],
  "filament_type": [
    "PLA Tough"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "50"
  ],
  "filament_z_hop": [
    "0.4"
  ],
  "hot_plate_temp": [
    "65"
  ],
  "cool_plate_temp": [
    "50"
  ],
  "filament_vendor": [
    "Artillery"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "220"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "0.98"
  ],
  "slow_down_min_speed": [
    "5"
  ],
  "textured_plate_temp": [
    "50"
  ],
  "filament_settings_id": [
    "Artillery PLA Tough"
  ],
  "filament_start_gcode": [
    ""
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "8"
  ],
  "fan_cooling_layer_time": [
    "80"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "50%"
  ],
  "filament_retraction_speed": [
    "40"
  ],
  "temperature_vitrification": [
    "190"
  ],
  "filament_retraction_length": [
    "1.3"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "65"
  ],
  "cool_plate_temp_initial_layer": [
    "50"
  ],
  "filament_max_volumetric_speed": [
    "21"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "220"
  ],
  "textured_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "190"
  ],
  "nozzle_temperature_range_high": [
    "230"
  ],
  "setting_id": "GFSA04",
  "filament_id": "GFL99",
  "compatible_printers": [
    "Artillery Sidewinder X3 Pro 0.4 nozzle",
    "Artillery Sidewinder X3 Plus 0.4 nozzle",
    "Artillery Sidewinder X4 Pro 0.4 nozzle",
    "Artillery Sidewinder X4 Plus 0.4 nozzle"
  ],
  "pressure_advance": [
    "0.046"
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "name": "Artillery PLA Tough"
}

Version history

View full history with diffs →

v1 created 2026-05-19 13:20