Artillery PLA Matte @Artillery M1 Pro 0.2 nozzle

Artillery · PLA MATTE · 0.20mm nozzle · by anycubic-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

Artillery PLA @Artillery M1 Pro 0.2 nozzle

→

Artillery PLA Matte @Artillery M1 Pro 0.2 nozzle

Compatible printers (1)

Artillery M1 Pro 0.2 nozzle

Settings

Basic information

Material variant: PLA Matte overridden
was PLA (inherited)
Vendor: Artillery inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.24 inherited
Cost (/kg): 20 inherited

Print temperature

Nozzle (initial layer) (°C): 210 inherited
Nozzle (other layers) (°C): 210 inherited
Chamber (°C): 0 inherited

Cooling

Fan minimum (%): 100 inherited
Fan maximum (%): 100 inherited
Disable fan for first N layers: 2 inherited
Full fan if layer below (sec): 100 inherited
Slow down if layer below (sec): 6 overridden
was 4 (inherited)
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 0.98 inherited
Max volumetric speed (mm³/s): 2 inherited

Retraction

Retraction length (mm): 1.3 inherited
Retraction speed (mm/s): 40 inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	50 overridden was 35	50 overridden was 35
Textured Cool Plate	40 inherited	40 inherited
Engineering Plate	0 inherited	0 inherited
High Temp Plate	60 inherited	60 inherited
Textured PEI Plate	55 overridden was 45	55 overridden was 45

Other settings

activate air filtration: 1 inherited
activate chamber temp control: 0 inherited
adaptive pressure advance: 0 inherited
adaptive pressure advance bridges: 0 inherited
adaptive pressure advance model: 0,0,0 0,0,0 inherited
adaptive pressure advance overhangs: 0 inherited
additional cooling fan speed: 50 inherited
compatible printers: Artillery M1 Pro 0.2 nozzle overridden
was Artillery M1 Pro 0.2 nozzle (inherited)
complete print exhaust fan speed: 100 inherited
dont slow down outer wall: 0 inherited
during print exhaust fan speed: 100 inherited
enable overhang bridge fan: 1 inherited
enable pressure advance: 1 inherited
filament cooling final speed: 3.4 inherited
filament cooling initial speed: 2.2 inherited
filament cooling moves: 4 inherited
filament id: Pfcf9c4c inherited
filament is support: 0 inherited
filament loading speed: 28 inherited
filament loading speed start: 3 inherited
filament long retractions when cut: nil inherited
filament minimal purge on wipe tower: 15 inherited
filament multitool ramming: 0 inherited
filament multitool ramming flow: 10 inherited
filament multitool ramming volume: 10 inherited
filament ramming parameters: 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 inherited
filament retract before wipe: nil inherited
filament retract lift above: nil inherited
filament retract lift below: nil inherited
filament retract lift enforce: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction distances when cut: nil inherited
filament retraction minimum travel: nil inherited
filament shrink: 100% inherited
filament shrinkage compensation z: 100% inherited
filament soluble: 0 inherited
filament stamping distance: 0 inherited
filament stamping loading speed: 0 inherited
filament toolchange delay: 0 inherited
filament unloading speed: 90 inherited
filament unloading speed start: 100 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: 0.4 inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
idle temperature: 0 inherited
instantiation: true overridden
was true (inherited)
nozzle temperature range high: 240 inherited
nozzle temperature range low: 190 inherited
overhang fan speed: 100 inherited
overhang fan threshold: 50% inherited
pellet flow coefficient: 0.4157 inherited
pressure advance: 0.032 inherited
reduce fan stop start freq: 1 inherited
required nozzle HRC: 0 inherited
slow down for layer cooling: 1 inherited
support material interface fan speed: -1 inherited
temperature vitrification: 190 inherited

Raw resolved JSON

{
  "type": "filament",
  "filament_id": "Pfcf9c4c",
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_cost": [
    "20"
  ],
  "filament_type": [
    "PLA Matte"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "0"
  ],
  "filament_notes": [
    ""
  ],
  "filament_z_hop": [
    "0.4"
  ],
  "hot_plate_temp": [
    "60"
  ],
  "cool_plate_temp": [
    "50"
  ],
  "filament_shrink": [
    "100%"
  ],
  "filament_vendor": [
    "Artillery"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "idle_temperature": [
    "0"
  ],
  "pressure_advance": [
    "0.032"
  ],
  "compatible_prints": [],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "210"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "chamber_temperature": [
    "0"
  ],
  "compatible_printers": [
    "Artillery M1 Pro 0.2 nozzle"
  ],
  "filament_flow_ratio": [
    "0.98"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "0"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "textured_plate_temp": [
    "55"
  ],
  "filament_settings_id": [
    "Artillery PLA Matte @Artillery M1 Pro 0.2 nozzle"
  ],
  "filament_start_gcode": [
    ""
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "6"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_cooling_moves": [
    "4"
  ],
  "filament_loading_speed": [
    "28"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "50%"
  ],
  "activate_air_filtration": [
    "1"
  ],
  "default_filament_colour": [
    ""
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "pellet_flow_coefficient": [
    "0.4157"
  ],
  "filament_unloading_speed": [
    "90"
  ],
  "textured_cool_plate_temp": [
    "40"
  ],
  "adaptive_pressure_advance": [
    "0"
  ],
  "dont_slow_down_outer_wall": [
    "0"
  ],
  "filament_retraction_speed": [
    "40"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "temperature_vitrification": [
    "190"
  ],
  "enable_overhang_bridge_fan": [
    "1"
  ],
  "filament_multitool_ramming": [
    "0"
  ],
  "filament_retraction_length": [
    "1.3"
  ],
  "filament_stamping_distance": [
    "0"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "compatible_prints_condition": "",
  "filament_deretraction_speed": [
    "nil"
  ],
  "filament_ramming_parameters": [
    "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "filament_retract_lift_above": [
    "nil"
  ],
  "filament_retract_lift_below": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "additional_cooling_fan_speed": [
    "50"
  ],
  "close_fan_the_first_x_layers": [
    "2"
  ],
  "eng_plate_temp_initial_layer": [
    "0"
  ],
  "filament_cooling_final_speed": [
    "3.4"
  ],
  "filament_loading_speed_start": [
    "3"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "60"
  ],
  "nozzle_temperature_range_low": [
    "190"
  ],
  "activate_chamber_temp_control": [
    "0"
  ],
  "compatible_printers_condition": "",
  "cool_plate_temp_initial_layer": [
    "50"
  ],
  "filament_max_volumetric_speed": [
    "2"
  ],
  "filament_retract_lift_enforce": [
    "nil"
  ],
  "nozzle_temperature_range_high": [
    "240"
  ],
  "during_print_exhaust_fan_speed": [
    "100"
  ],
  "filament_cooling_initial_speed": [
    "2.2"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "filament_unloading_speed_start": [
    "100"
  ],
  "adaptive_pressure_advance_model": [
    "0,0,0\n0,0,0"
  ],
  "filament_multitool_ramming_flow": [
    "10"
  ],
  "filament_stamping_loading_speed": [
    "0"
  ],
  "complete_print_exhaust_fan_speed": [
    "100"
  ],
  "nozzle_temperature_initial_layer": [
    "210"
  ],
  "adaptive_pressure_advance_bridges": [
    "0"
  ],
  "filament_multitool_ramming_volume": [
    "10"
  ],
  "filament_shrinkage_compensation_z": [
    "100%"
  ],
  "textured_plate_temp_initial_layer": [
    "55"
  ],
  "filament_long_retractions_when_cut": [
    "nil"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "adaptive_pressure_advance_overhangs": [
    "0"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "support_material_interface_fan_speed": [
    "-1"
  ],
  "filament_retraction_distances_when_cut": [
    "nil"
  ],
  "textured_cool_plate_temp_initial_layer": [
    "40"
  ],
  "name": "Artillery PLA Matte @Artillery M1 Pro 0.2 nozzle"
}

Version history

View full history with diffs →

v1 created 2026-05-19 13:20