Prusament PC-CF @CORE One 0.8

Prusa · PC · by anycubic-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Strip G-code from download

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pc

→

Prusament PC-CF @CORE One

→

Prusament PC-CF @CORE One 0.8

Compatible printers (2)

Prusa CORE One 0.8 nozzle
Prusa CORE One HF 0.8 nozzle

Settings

Basic information

Material variant: PC inherited
Vendor: Prusa Polymers inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.22 inherited
Cost (/kg): 74.99 inherited

Print temperature

Nozzle (initial layer) (°C): 285 inherited
Nozzle (other layers) (°C): 285 inherited
Chamber (°C): 40 inherited

Cooling

Fan minimum (%): 15 inherited
Fan maximum (%): 30 inherited
Disable fan for first N layers: 4 inherited
Full fan if layer below (sec): 25 overridden
was 15 (inherited)
Slow down if layer below (sec): 20 inherited
Min speed when slowed (mm/s): 15 inherited

Flow

Flow ratio: 1.04 inherited
Max volumetric speed (mm³/s): 18 overridden
was 9 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	0 inherited	0 inherited
Engineering Plate	100 inherited	100 inherited
High Temp Plate	110 inherited	115 inherited
Textured PEI Plate	100 inherited	100 inherited

Custom G-code

filament_start_gcode inherited

M900 K{if nozzle_diameter[filament_extruder_id]==0.4}0.07{elsif nozzle_diameter[filament_extruder_id]==0.3}0.09{elsif nozzle_diameter[filament_extruder_id]==0.35}0.08{elsif nozzle_diameter[filament_extruder_id]==0.6}0.04{elsif nozzle_diameter[filament_extruder_id]==0.5}0.05{elsif nozzle_diameter[filament_extruder_id]==0.8}0.02{else}0{endif} ; Filament gcode

{if printer_notes=~/.*(MK4IS|XLIS|MK4S|MK3.9S|CORE One).*/}
M572 S{if nozzle_diameter[filament_extruder_id]==0.4}0.05{elsif nozzle_diameter[filament_extruder_id]==0.5}0.035{elsif nozzle_diameter[filament_extruder_id]==0.6}0.025{elsif nozzle_diameter[filament_extruder_id]==0.8}0.016{elsif nozzle_diameter[filament_extruder_id]==0.25}0.14{elsif nozzle_diameter[filament_extruder_id]==0.3}0.09{else}0{endif} ; Filament gcode
{endif}

M142 S45 ; set heatbreak target temp

Other settings

bed type: Cool Plate inherited
compatible printers: Prusa CORE One 0.8 nozzle, Prusa CORE One HF 0.8 nozzle overridden
was Prusa CORE One 0.25 nozzle, Prusa CORE One 0.3 nozzle, Prusa CORE One 0.4 nozzle, Prusa CORE One 0.5 nozzle, Prusa CORE One HF 0.4 nozzle, Prusa CORE One HF 0.5 nozzle (inherited)
filament id: Prusament PC-CF @CORE One 0.8 overridden
was Prusament PC-CF @CORE One (inherited)
filament minimal purge on wipe tower: 35 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: 0.2 inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
idle temperature: 130 inherited
instantiation: true overridden
was true (inherited)
nozzle temperature range high: 280 inherited
nozzle temperature range low: 250 inherited
overhang fan speed: 30 overridden
was 25 (inherited)
overhang fan threshold: 25% inherited
reduce fan stop start freq: 0 inherited
setting id: GFSA04 overridden
was GFSA04 (inherited)
slow down for layer cooling: 1 inherited
temperature vitrification: 140 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "30"
  ],
  "fan_min_speed": [
    "15"
  ],
  "filament_cost": [
    "74.99"
  ],
  "filament_type": [
    "PC"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "100"
  ],
  "filament_z_hop": [
    "0.2"
  ],
  "hot_plate_temp": [
    "115"
  ],
  "cool_plate_temp": [
    "0"
  ],
  "filament_vendor": [
    "Prusa Polymers"
  ],
  "filament_density": [
    "1.22"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; Filament-specific end gcode"
  ],
  "nozzle_temperature": [
    "285"
  ],
  "overhang_fan_speed": [
    "30"
  ],
  "filament_flow_ratio": [
    "1.04"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "textured_plate_temp": [
    "100"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "M900 K{if nozzle_diameter[filament_extruder_id]==0.4}0.07{elsif nozzle_diameter[filament_extruder_id]==0.3}0.09{elsif nozzle_diameter[filament_extruder_id]==0.35}0.08{elsif nozzle_diameter[filament_extruder_id]==0.6}0.04{elsif nozzle_diameter[filament_extruder_id]==0.5}0.05{elsif nozzle_diameter[filament_extruder_id]==0.8}0.02{else}0{endif} ; Filament gcode\n\n{if printer_notes=~/.*(MK4IS|XLIS|MK4S|MK3.9S|CORE One).*/}\nM572 S{if nozzle_diameter[filament_extruder_id]==0.4}0.05{elsif nozzle_diameter[filament_extruder_id]==0.5}0.035{elsif nozzle_diameter[filament_extruder_id]==0.6}0.025{elsif nozzle_diameter[filament_extruder_id]==0.8}0.016{elsif nozzle_diameter[filament_extruder_id]==0.25}0.14{elsif nozzle_diameter[filament_extruder_id]==0.3}0.09{else}0{endif} ; Filament gcode\n{endif}\n\nM142 S45 ; set heatbreak target temp"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "20"
  ],
  "fan_cooling_layer_time": [
    "25"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "140"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "0"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "4"
  ],
  "eng_plate_temp_initial_layer": [
    "100"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "110"
  ],
  "cool_plate_temp_initial_layer": [
    "0"
  ],
  "filament_max_volumetric_speed": [
    "18"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "285"
  ],
  "textured_plate_temp_initial_layer": [
    "100"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "35"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "250"
  ],
  "nozzle_temperature_range_high": [
    "280"
  ],
  "setting_id": "GFSA04",
  "filament_id": "Prusament PC-CF @CORE One 0.8",
  "filament_notes": [
    ""
  ],
  "idle_temperature": [
    "130"
  ],
  "chamber_temperature": [
    "40"
  ],
  "compatible_printers": [
    "Prusa CORE One 0.8 nozzle",
    "Prusa CORE One HF 0.8 nozzle"
  ],
  "name": "Prusament PC-CF @CORE One 0.8"
}

Version history

View full history with diffs →

v1 created 2026-05-19 13:19