Snapmaker PLA SnapSpeed @U1

Snapmaker · PLA · by anycubic-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

Snapmaker PLA SnapSpeed @U1 base

→

Snapmaker PLA SnapSpeed @U1

Compatible printers (1)

Snapmaker U1 (0.4 nozzle)

Settings

Basic information

Material variant: PLA overridden
was PLA (inherited)
Vendor: Snapmaker overridden
Diameter (mm): 1.75 overridden
Density (g/cm³): 1.24 overridden
was 1.24 (inherited)
Cost (/kg): 20 overridden
was 20 (inherited)

Print temperature

Nozzle (initial layer) (°C): 220 overridden
was 220 (inherited)
Nozzle (other layers) (°C): 220 overridden
was 220 (inherited)
Chamber (°C): 0 overridden

Cooling

Fan minimum (%): 100 overridden
was 100 (inherited)
Fan maximum (%): 100 overridden
was 100 (inherited)
Disable fan for first N layers: 3 overridden
was 1 (inherited)
Full fan if layer below (sec): 100 overridden
was 100 (inherited)
Slow down if layer below (sec): 4 overridden
was 4 (inherited)
Min speed when slowed (mm/s): 20 overridden
was 10 (inherited)

Flow

Flow ratio: 0.99 overridden
Max volumetric speed (mm³/s): 18 overridden
was 12 (inherited)

Retraction

Retraction length (mm): 0.8 overridden
was nil (inherited)
Retraction speed (mm/s): 30 overridden
Deretraction speed (mm/s): nil overridden

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	60 overridden was 60	60 overridden was 60
Textured Cool Plate	40 overridden	40 overridden
Engineering Plate	60 overridden was 60	60 overridden was 60
High Temp Plate	55 overridden was 60	55 overridden was 60
Textured PEI Plate	60 overridden was 60	60 overridden was 60

Other settings

activate air filtration: 0 overridden
activate chamber temp control: 0 overridden
adaptive pressure advance: 0 overridden
adaptive pressure advance bridges: 0 overridden
adaptive pressure advance model: 0,0,0 0,0,0 overridden
adaptive pressure advance overhangs: 0 overridden
additional cooling fan speed: 70 overridden
was 70 (inherited)
compatible printers: Snapmaker U1 (0.4 nozzle) overridden
complete print exhaust fan speed: 80 overridden
dont slow down outer wall: 0 overridden
during print exhaust fan speed: 60 overridden
enable overhang bridge fan: 1 overridden
enable pressure advance: 1 overridden
filament cooling final speed: 3.5 overridden
was 60 (inherited)
filament cooling initial speed: 10 overridden
was 35 (inherited)
filament cooling moves: 2 overridden
was 2 (inherited)
filament id: 141703112701 inherited
filament is support: 0 overridden
filament load time: 2 inherited
filament loading speed: 10 overridden
was 35 (inherited)
filament loading speed start: 50 overridden
was 35 (inherited)
filament long retractions when cut: nil overridden
filament minimal purge on wipe tower: 15 overridden
filament multitool ramming: 1 overridden
filament multitool ramming flow: 40 overridden
filament multitool ramming volume: 5 overridden
filament ramming parameters: 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 overridden
filament retract before wipe: nil overridden
filament retract lift above: nil overridden
filament retract lift below: nil overridden
filament retract lift enforce: nil overridden
filament retract restart extra: nil overridden
filament retract when changing layer: nil overridden
filament retraction distances when cut: nil overridden
filament retraction minimum travel: nil overridden
filament shrink: 100% overridden
filament shrinkage compensation z: 100% overridden
filament soluble: 0 overridden
filament stamping distance: 45 overridden
filament stamping loading speed: 29 overridden
filament toolchange delay: 0 overridden
filament unload time: 2 inherited
filament unloading speed: 100 overridden
was 35 (inherited)
filament unloading speed start: 100 overridden
was 35 (inherited)
filament wipe: nil overridden
filament wipe distance: nil overridden
filament z hop: nil overridden
filament z hop types: nil overridden
full fan speed layer: 0 overridden
idle temperature: 0 overridden
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 230 overridden
was 230 (inherited)
nozzle temperature range low: 190 overridden
was 190 (inherited)
overhang fan speed: 100 overridden
was 100 (inherited)
overhang fan threshold: 50% overridden
was 50% (inherited)
pellet flow coefficient: 0.4157 overridden
pressure advance: 0.026 overridden
reduce fan stop start freq: 1 overridden
was 1 (inherited)
required nozzle HRC: 0 overridden
setting id: 119531393501 overridden
slow down for layer cooling: 1 overridden
was 1 (inherited)
support material interface fan speed: -1 overridden
temperature vitrification: 60 overridden
was 60 (inherited)

Raw resolved JSON

{
  "type": "filament",
  "filament_id": "141703112701",
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_cost": [
    "20"
  ],
  "filament_type": [
    "PLA"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "60"
  ],
  "hot_plate_temp": [
    "55"
  ],
  "cool_plate_temp": [
    "60"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "filament_load_time": [
    "2"
  ],
  "nozzle_temperature": [
    "220"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "textured_plate_temp": [
    "60"
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_unload_time": [
    "2"
  ],
  "slow_down_layer_time": [
    "4"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_cooling_moves": [
    "2"
  ],
  "filament_loading_speed": [
    "10"
  ],
  "overhang_fan_threshold": [
    "50%"
  ],
  "filament_unloading_speed": [
    "100"
  ],
  "temperature_vitrification": [
    "60"
  ],
  "filament_retraction_length": [
    "0.8"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "additional_cooling_fan_speed": [
    "70"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "60"
  ],
  "filament_cooling_final_speed": [
    "3.5"
  ],
  "filament_loading_speed_start": [
    "50"
  ],
  "hot_plate_temp_initial_layer": [
    "55"
  ],
  "nozzle_temperature_range_low": [
    "190"
  ],
  "cool_plate_temp_initial_layer": [
    "60"
  ],
  "filament_max_volumetric_speed": [
    "18"
  ],
  "nozzle_temperature_range_high": [
    "230"
  ],
  "filament_cooling_initial_speed": [
    "10"
  ],
  "filament_unloading_speed_start": [
    "100"
  ],
  "nozzle_temperature_initial_layer": [
    "220"
  ],
  "textured_plate_temp_initial_layer": [
    "60"
  ],
  "setting_id": "119531393501",
  "filament_wipe": [
    "nil"
  ],
  "filament_notes": [
    ""
  ],
  "filament_z_hop": [
    "nil"
  ],
  "filament_shrink": [
    "100%"
  ],
  "filament_vendor": [
    "Snapmaker"
  ],
  "filament_soluble": [
    "0"
  ],
  "idle_temperature": [
    "0"
  ],
  "pressure_advance": [
    "0.026"
  ],
  "compatible_prints": [],
  "filament_diameter": [
    "1.75"
  ],
  "chamber_temperature": [
    "0"
  ],
  "compatible_printers": [
    "Snapmaker U1 (0.4 nozzle)"
  ],
  "filament_flow_ratio": [
    "0.99"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "0"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "activate_air_filtration": [
    "0"
  ],
  "default_filament_colour": [
    ""
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "pellet_flow_coefficient": [
    "0.4157"
  ],
  "textured_cool_plate_temp": [
    "40"
  ],
  "adaptive_pressure_advance": [
    "0"
  ],
  "dont_slow_down_outer_wall": [
    "0"
  ],
  "filament_retraction_speed": [
    "30"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "enable_overhang_bridge_fan": [
    "1"
  ],
  "filament_multitool_ramming": [
    "1"
  ],
  "filament_stamping_distance": [
    "45"
  ],
  "compatible_prints_condition": "",
  "filament_deretraction_speed": [
    "nil"
  ],
  "filament_ramming_parameters": [
    "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "filament_retract_lift_above": [
    "nil"
  ],
  "filament_retract_lift_below": [
    "nil"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "activate_chamber_temp_control": [
    "0"
  ],
  "compatible_printers_condition": "",
  "filament_retract_lift_enforce": [
    "nil"
  ],
  "during_print_exhaust_fan_speed": [
    "60"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "adaptive_pressure_advance_model": [
    "0,0,0\n0,0,0"
  ],
  "filament_multitool_ramming_flow": [
    "40"
  ],
  "filament_stamping_loading_speed": [
    "29"
  ],
  "complete_print_exhaust_fan_speed": [
    "80"
  ],
  "adaptive_pressure_advance_bridges": [
    "0"
  ],
  "filament_multitool_ramming_volume": [
    "5"
  ],
  "filament_shrinkage_compensation_z": [
    "100%"
  ],
  "filament_long_retractions_when_cut": [
    "nil"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "adaptive_pressure_advance_overhangs": [
    "0"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "support_material_interface_fan_speed": [
    "-1"
  ],
  "filament_retraction_distances_when_cut": [
    "nil"
  ],
  "textured_cool_plate_temp_initial_layer": [
    "40"
  ],
  "name": "Snapmaker PLA SnapSpeed @U1",
  "filament_settings_id": [
    "Snapmaker PLA SnapSpeed @U1"
  ]
}

Version history

View full history with diffs →

v1 created 2026-05-19 13:16