QIDI PPS-GF

Generic · PPS-GF · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pa

→

QIDI PPS-GF

Compatible printers (9)

Qidi X-Max 3 0.4 nozzle
Qidi X-Max 3 0.6 nozzle
Qidi X-Max 3 0.8 nozzle
Qidi X-Plus 3 0.4 nozzle
Qidi X-Plus 3 0.6 nozzle
Qidi X-Plus 3 0.8 nozzle
Qidi X-Smart 3 0.4 nozzle
Qidi X-Smart 3 0.6 nozzle
Qidi X-Smart 3 0.8 nozzle

Inherited from this (6)

Settings

Basic information

Material variant: PPS-GF overridden
was PA (inherited)
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.3 overridden
was 1.04 (inherited)
Cost (/kg): 20 inherited

Print temperature

Nozzle (initial layer) (°C): 320 overridden
was 270 (inherited)
Nozzle (other layers) (°C): 320 overridden
was 270 (inherited)
Chamber (°C): 0 overridden

Cooling

Fan minimum (%): 10 overridden
was 0 (inherited)
Fan maximum (%): 90 overridden
was 60 (inherited)
Disable fan for first N layers: 3 overridden
was 3 (inherited)
Full fan if layer below (sec): 30 overridden
was 10 (inherited)
Slow down if layer below (sec): 6 overridden
was 2 (inherited)
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 0.97 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 12 overridden
was 8 (inherited)

Retraction

Retraction length (mm): 1.0 inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	0 inherited	0 inherited
Engineering Plate	100 inherited	100 inherited
High Temp Plate	90 overridden was 100	90 overridden was 100
Textured PEI Plate	100 inherited	100 inherited

Other settings

bed type: Cool Plate inherited
box temperature: 65 overridden
box temperature range high: 65 overridden
box temperature range low: 0 overridden
compatible printers: Qidi X-Smart 3 0.4 nozzle, Qidi X-Plus 3 0.4 nozzle, Qidi X-Max 3 0.4 nozzle, Qidi X-Smart 3 0.6 nozzle, Qidi X-Plus 3 0.6 nozzle, Qidi X-Max 3 0.6 nozzle, Qidi X-Smart 3 0.8 nozzle, Qidi X-Plus 3 0.8 nozzle, Qidi X-Max 3 0.8 nozzle overridden
during print exhaust fan speed: 0 overridden
filament adhesiveness category: 801 overridden
filament id: QD_0_1_46 overridden
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: 0.0 inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
impact strength z: 2.8 overridden
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 350 overridden
was 300 (inherited)
nozzle temperature range low: 300 overridden
was 260 (inherited)
overhang fan speed: 50 overridden
was 60 (inherited)
overhang fan threshold: 0% overridden
was 95% (inherited)
pressure advance: 0.032 overridden
reduce fan stop start freq: 0 inherited
setting id: GFSN99 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 180 overridden
was 108 (inherited)

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "90"
  ],
  "fan_min_speed": [
    "10"
  ],
  "filament_cost": [
    "20"
  ],
  "filament_type": [
    "PPS-GF"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "100"
  ],
  "filament_z_hop": [
    "0.0"
  ],
  "hot_plate_temp": [
    "90"
  ],
  "cool_plate_temp": [
    "0"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.3"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "320"
  ],
  "overhang_fan_speed": [
    "50"
  ],
  "filament_flow_ratio": [
    "0.97"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "textured_plate_temp": [
    "100"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; Filament gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "6"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "0%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "180"
  ],
  "filament_retraction_length": [
    "1.0"
  ],
  "reduce_fan_stop_start_freq": [
    "0"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "100"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "90"
  ],
  "cool_plate_temp_initial_layer": [
    "0"
  ],
  "filament_max_volumetric_speed": [
    "12"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "320"
  ],
  "textured_plate_temp_initial_layer": [
    "100"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "300"
  ],
  "nozzle_temperature_range_high": [
    "350"
  ],
  "setting_id": "GFSN99",
  "filament_id": "QD_0_1_46",
  "box_temperature": [
    "65"
  ],
  "pressure_advance": [
    "0.032"
  ],
  "impact_strength_z": [
    "2.8"
  ],
  "chamber_temperature": [
    "0"
  ],
  "compatible_printers": [
    "Qidi X-Smart 3 0.4 nozzle",
    "Qidi X-Plus 3 0.4 nozzle",
    "Qidi X-Max 3 0.4 nozzle",
    "Qidi X-Smart 3 0.6 nozzle",
    "Qidi X-Plus 3 0.6 nozzle",
    "Qidi X-Max 3 0.6 nozzle",
    "Qidi X-Smart 3 0.8 nozzle",
    "Qidi X-Plus 3 0.8 nozzle",
    "Qidi X-Max 3 0.8 nozzle"
  ],
  "box_temperature_range_low": [
    "0"
  ],
  "box_temperature_range_high": [
    "65"
  ],
  "during_print_exhaust_fan_speed": [
    "0"
  ],
  "filament_adhesiveness_category": [
    "801"
  ],
  "name": "QIDI PPS-GF"
}

Version history

View full history with diffs →

v1 created 2026-05-19 04:34