QIDI ABS Rapido @Qidi X-Plus 4 0.6 nozzle

Generic · ABS · 0.60mm nozzle · by anycubic-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_abs

→

QIDI ABS Rapido

→

QIDI ABS Rapido @Qidi X-Plus 4 0.6 nozzle

Compatible printers (1)

Qidi X-Plus 4 0.6 nozzle

Settings

Basic information

Material variant: ABS inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.05 inherited
Cost (/kg): 30 inherited

Print temperature

Nozzle (initial layer) (°C): 250 inherited
Nozzle (other layers) (°C): 250 overridden
was 250 (inherited)
Chamber (°C): 55 overridden
was 55 (inherited)

Cooling

Fan minimum (%): 20 inherited
Fan maximum (%): 80 overridden
was 80 (inherited)
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 60 inherited
Slow down if layer below (sec): 3 inherited
Min speed when slowed (mm/s): 20 overridden
was 20 (inherited)

Flow

Flow ratio: 0.95 overridden
was 0.95 (inherited)
Max volumetric speed (mm³/s): 24.5 overridden
was 22 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	105 inherited	105 inherited
Engineering Plate	105 inherited	105 inherited
High Temp Plate	90 overridden was 105	105 inherited
Textured PEI Plate	105 inherited	105 inherited

Other settings

activate air filtration: 1 overridden
activate chamber temp control: 0 overridden
additional cooling fan speed: 0 inherited
bed type: Cool Plate inherited
compatible printers: Qidi X-Plus 4 0.6 nozzle overridden
was Qidi X-Plus 0.4 nozzle, Qidi X-Max 0.4 nozzle, Qidi X-CF Pro 0.4 nozzle, Qidi X-Smart 3 0.4 nozzle, Qidi X-Plus 3 0.4 nozzle, Qidi X-Max 3 0.4 nozzle (inherited)
during print exhaust fan speed: 0 overridden
enable pressure advance: 1 overridden
was 1 (inherited)
filament id: GFB99 overridden
was GFB99 (inherited)
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was true (inherited)
nozzle temperature range high: 280 inherited
nozzle temperature range low: 240 inherited
overhang fan speed: 80 overridden
was 80 (inherited)
overhang fan threshold: 25% inherited
pressure advance: 0.014 overridden
was 0.021 (inherited)
reduce fan stop start freq: 1 inherited
setting id: GFSA04 overridden
was GFSA04 (inherited)
slow down for layer cooling: 1 inherited
temperature vitrification: 110 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "80"
  ],
  "fan_min_speed": [
    "20"
  ],
  "filament_cost": [
    "30"
  ],
  "filament_type": [
    "ABS"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "105"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "105"
  ],
  "cool_plate_temp": [
    "105"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.05"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "250"
  ],
  "overhang_fan_speed": [
    "80"
  ],
  "filament_flow_ratio": [
    "0.95"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "textured_plate_temp": [
    "105"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "3"
  ],
  "fan_cooling_layer_time": [
    "60"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "110"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "105"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "90"
  ],
  "cool_plate_temp_initial_layer": [
    "105"
  ],
  "filament_max_volumetric_speed": [
    "24.5"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "250"
  ],
  "textured_plate_temp_initial_layer": [
    "105"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "240"
  ],
  "nozzle_temperature_range_high": [
    "280"
  ],
  "setting_id": "GFSA04",
  "filament_id": "GFB99",
  "pressure_advance": [
    "0.014"
  ],
  "chamber_temperature": [
    "55"
  ],
  "compatible_printers": [
    "Qidi X-Plus 4 0.6 nozzle"
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "activate_air_filtration": [
    "1"
  ],
  "activate_chamber_temp_control": [
    "0"
  ],
  "during_print_exhaust_fan_speed": [
    "0"
  ],
  "name": "QIDI ABS Rapido @Qidi X-Plus 4 0.6 nozzle"
}

Version history

View full history with diffs →

v1 created 2026-05-19 13:09