FLSun T1 ABS

Generic · ABS · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_abs

→

FLSun Generic ABS

→

FLSun T1 ABS

Compatible printers (1)

FLSun T1 0.4 nozzle

Settings

Basic information

Material variant: ABS inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.05 overridden
was 1.24 (inherited)
Cost (/kg): 0 overridden
was 30 (inherited)

Print temperature

Nozzle (initial layer) (°C): 280 overridden
was 250 (inherited)
Nozzle (other layers) (°C): 280 overridden
was 250 (inherited)

Cooling

Fan minimum (%): 10 overridden
was 18 (inherited)
Fan maximum (%): 50 overridden
was 60 (inherited)
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 30 overridden
was 5 (inherited)
Slow down if layer below (sec): 12 overridden
was 3 (inherited)
Min speed when slowed (mm/s): 30 overridden
was 30 (inherited)

Flow

Flow ratio: 0.95 overridden
was 0.926 (inherited)
Max volumetric speed (mm³/s): 20 overridden
was 12 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	105 inherited	105 inherited
Engineering Plate	105 inherited	105 inherited
High Temp Plate	90 overridden was 105	90 overridden was 105
Textured PEI Plate	105 inherited	105 inherited

Other settings

activate air filtration: 1 overridden
additional cooling fan speed: 0 inherited
bed type: Cool Plate inherited
compatible printers: FLSun T1 0.4 nozzle overridden
was FLSun Q5 0.4 nozzle, FLSun QQ-S Pro 0.4 nozzle, FLSun Super Racer 0.4 nozzle, FLSun V400 0.4 nozzle (inherited)
complete print exhaust fan speed: 0 overridden
dont slow down outer wall: 1 overridden
during print exhaust fan speed: 0 overridden
filament id: GFB99 overridden
was GFB99 (inherited)
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 3 overridden
was 0 (inherited)
instantiation: true overridden
was true (inherited)
nozzle temperature range high: 300 overridden
was 280 (inherited)
nozzle temperature range low: 240 overridden
was 240 (inherited)
overhang fan speed: 50 overridden
was 40 (inherited)
overhang fan threshold: 25% inherited
reduce fan stop start freq: 1 inherited
setting id: GFSA04 overridden
was GFSA04 (inherited)
slow down for layer cooling: 1 inherited
temperature vitrification: 100 overridden
was 110 (inherited)

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "50"
  ],
  "fan_min_speed": [
    "10"
  ],
  "filament_cost": [
    "0"
  ],
  "filament_type": [
    "ABS"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "105"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "90"
  ],
  "cool_plate_temp": [
    "105"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.05"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "280"
  ],
  "overhang_fan_speed": [
    "50"
  ],
  "filament_flow_ratio": "0.95",
  "slow_down_min_speed": [
    "30"
  ],
  "textured_plate_temp": [
    "105"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "3"
  ],
  "slow_down_layer_time": [
    "12"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "100"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "105"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "90"
  ],
  "cool_plate_temp_initial_layer": [
    "105"
  ],
  "filament_max_volumetric_speed": [
    "20"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "280"
  ],
  "textured_plate_temp_initial_layer": [
    "105"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "240"
  ],
  "nozzle_temperature_range_high": [
    "300"
  ],
  "setting_id": "GFSA04",
  "filament_id": "GFB99",
  "compatible_printers": [
    "FLSun T1 0.4 nozzle"
  ],
  "activate_air_filtration": [
    "1"
  ],
  "dont_slow_down_outer_wall": [
    "1"
  ],
  "during_print_exhaust_fan_speed": [
    "0"
  ],
  "complete_print_exhaust_fan_speed": [
    "0"
  ],
  "name": "FLSun T1 ABS"
}

Version history

View full history with diffs →

v1 created 2026-05-19 04:33