Blocks Generic ASA

Generic · ASA · by anycubic-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_asa

→

Blocks Generic ASA

Compatible printers (8)

BLOCKS RD50 V2
BLOCKS RD50 V2 0.4 nozzle
BLOCKS RD50 V2 0.6 nozzle
BLOCKS RD50 V2 0.8 nozzle
BLOCKS RF50
BLOCKS RF50 0.4 nozzle
BLOCKS RF50 0.6 nozzle
BLOCKS RF50 0.8 nozzle

Settings

Basic information

Material variant: ASA inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.04 overridden
was 1.24 (inherited)
Cost (/kg): 30 inherited

Print temperature

Nozzle (initial layer) (°C): 260 overridden
was 260 (inherited)
Nozzle (other layers) (°C): 260 overridden
was 250 (inherited)

Cooling

Fan minimum (%): 10 overridden
was 10 (inherited)
Fan maximum (%): 100 overridden
was 60 (inherited)
Disable fan for first N layers: 4 overridden
was 1 (inherited)
Full fan if layer below (sec): 30 overridden
was 35 (inherited)
Slow down if layer below (sec): 10 overridden
was 3 (inherited)
Min speed when slowed (mm/s): 30 overridden
was 30 (inherited)

Flow

Flow ratio: 0.95 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 18 overridden
was 20 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	105 inherited	105 inherited
Engineering Plate	105 inherited	105 inherited
High Temp Plate	90 overridden was 105	90 overridden was 105
Textured PEI Plate	105 inherited	105 inherited

Other settings

activate air filtration: 1 overridden
additional cooling fan speed: 0 overridden
was 0 (inherited)
bed type: Cool Plate inherited
compatible printers: BLOCKS RD50 V2 0.4 nozzle, BLOCKS RD50 V2 0.6 nozzle, BLOCKS RD50 V2 0.8 nozzle, BLOCKS RD50 V2, BLOCKS RF50 0.4 nozzle, BLOCKS RF50 0.6 nozzle, BLOCKS RF50 0.8 nozzle, BLOCKS RF50 overridden
complete print exhaust fan speed: 100 overridden
during print exhaust fan speed: 100 overridden
enable overhang bridge fan: 1 overridden
filament id: BSFI005 overridden
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament shrink: 99.5% overridden
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 280 overridden
was 270 (inherited)
nozzle temperature range low: 230 overridden
was 240 (inherited)
overhang fan speed: 100% overridden
was 80 (inherited)
overhang fan threshold: 25% overridden
was 25% (inherited)
reduce fan stop start freq: 1 overridden
was 1 (inherited)
setting id: BSSI005 overridden
slow down for layer cooling: 1 overridden
was 1 (inherited)
temperature vitrification: 110 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "10"
  ],
  "filament_cost": [
    "30"
  ],
  "filament_type": [
    "ASA"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "105"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "90"
  ],
  "cool_plate_temp": [
    "105"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.04"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "260"
  ],
  "overhang_fan_speed": [
    "100%"
  ],
  "filament_flow_ratio": [
    "0.95"
  ],
  "slow_down_min_speed": [
    "30"
  ],
  "textured_plate_temp": [
    "105"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "10"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "110"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "4"
  ],
  "eng_plate_temp_initial_layer": [
    "105"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "90"
  ],
  "cool_plate_temp_initial_layer": [
    "105"
  ],
  "filament_max_volumetric_speed": [
    "18"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "260"
  ],
  "textured_plate_temp_initial_layer": [
    "105"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "230"
  ],
  "nozzle_temperature_range_high": [
    "280"
  ],
  "setting_id": "BSSI005",
  "filament_id": "BSFI005",
  "filament_shrink": [
    "99.5%"
  ],
  "compatible_printers": [
    "BLOCKS RD50 V2 0.4 nozzle",
    "BLOCKS RD50 V2 0.6 nozzle",
    "BLOCKS RD50 V2 0.8 nozzle",
    "BLOCKS RD50 V2",
    "BLOCKS RF50 0.4 nozzle",
    "BLOCKS RF50 0.6 nozzle",
    "BLOCKS RF50 0.8 nozzle",
    "BLOCKS RF50"
  ],
  "activate_air_filtration": [
    "1"
  ],
  "enable_overhang_bridge_fan": [
    "1"
  ],
  "during_print_exhaust_fan_speed": [
    "100"
  ],
  "complete_print_exhaust_fan_speed": [
    "100"
  ],
  "name": "Blocks Generic ASA"
}

Version history

View full history with diffs →

v1 created 2026-05-19 13:08