Blocks Generic PA-CF

Generic · PA-CF · by anycubic-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pa

→

Blocks Generic PA-CF

Compatible printers (8)

BLOCKS RD50 V2
BLOCKS RD50 V2 0.4 nozzle
BLOCKS RD50 V2 0.6 nozzle
BLOCKS RD50 V2 0.8 nozzle
BLOCKS RF50
BLOCKS RF50 0.4 nozzle
BLOCKS RF50 0.6 nozzle
BLOCKS RF50 0.8 nozzle

Settings

Basic information

Material variant: PA-CF overridden
was PA (inherited)
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.25 overridden
was 1.04 (inherited)
Cost (/kg): 20 inherited

Print temperature

Nozzle (initial layer) (°C): 255 overridden
was 270 (inherited)
Nozzle (other layers) (°C): 250 overridden
was 270 (inherited)

Cooling

Fan minimum (%): 0 overridden
was 0 (inherited)
Fan maximum (%): 60 overridden
was 60 (inherited)
Disable fan for first N layers: 3 overridden
was 3 (inherited)
Full fan if layer below (sec): 4 overridden
was 10 (inherited)
Slow down if layer below (sec): 2 overridden
was 2 (inherited)
Min speed when slowed (mm/s): 10 overridden
was 10 (inherited)

Flow

Flow ratio: 0.95 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 10 overridden
was 8 (inherited)

Retraction

Retraction length (mm): 1.2 overridden
was 1.0 (inherited)
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	0 inherited	0 inherited
Engineering Plate	100 inherited	100 inherited
High Temp Plate	90 overridden was 100	90 overridden was 100
Textured PEI Plate	100 inherited	100 inherited

Other settings

activate air filtration: 1 overridden
additional cooling fan speed: 0 overridden
bed type: Cool Plate inherited
compatible printers: BLOCKS RD50 V2 0.4 nozzle, BLOCKS RD50 V2 0.6 nozzle, BLOCKS RD50 V2 0.8 nozzle, BLOCKS RD50 V2, BLOCKS RF50 0.4 nozzle, BLOCKS RF50 0.6 nozzle, BLOCKS RF50 0.8 nozzle, BLOCKS RF50 overridden
complete print exhaust fan speed: 100 overridden
during print exhaust fan speed: 80 overridden
enable overhang bridge fan: 1 overridden
filament id: BSFI007 overridden
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: 0.0 overridden
was 0.0 (inherited)
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 290 overridden
was 300 (inherited)
nozzle temperature range low: 240 overridden
was 260 (inherited)
overhang fan speed: 80% overridden
was 60 (inherited)
overhang fan threshold: 95% overridden
was 95% (inherited)
reduce fan stop start freq: 0 overridden
was 0 (inherited)
setting id: BSSI007 overridden
slow down for layer cooling: 1 overridden
was 1 (inherited)
temperature vitrification: 108 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "60"
  ],
  "fan_min_speed": [
    "0"
  ],
  "filament_cost": [
    "20"
  ],
  "filament_type": [
    "PA-CF"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "100"
  ],
  "filament_z_hop": [
    "0.0"
  ],
  "hot_plate_temp": [
    "90"
  ],
  "cool_plate_temp": [
    "0"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.25"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "250"
  ],
  "overhang_fan_speed": [
    "80%"
  ],
  "filament_flow_ratio": [
    "0.95"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "textured_plate_temp": [
    "100"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; Filament gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "2"
  ],
  "fan_cooling_layer_time": [
    "4"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "95%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "108"
  ],
  "filament_retraction_length": [
    "1.2"
  ],
  "reduce_fan_stop_start_freq": [
    "0"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "100"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "90"
  ],
  "cool_plate_temp_initial_layer": [
    "0"
  ],
  "filament_max_volumetric_speed": [
    "10"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "255"
  ],
  "textured_plate_temp_initial_layer": [
    "100"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "240"
  ],
  "nozzle_temperature_range_high": [
    "290"
  ],
  "setting_id": "BSSI007",
  "filament_id": "BSFI007",
  "compatible_printers": [
    "BLOCKS RD50 V2 0.4 nozzle",
    "BLOCKS RD50 V2 0.6 nozzle",
    "BLOCKS RD50 V2 0.8 nozzle",
    "BLOCKS RD50 V2",
    "BLOCKS RF50 0.4 nozzle",
    "BLOCKS RF50 0.6 nozzle",
    "BLOCKS RF50 0.8 nozzle",
    "BLOCKS RF50"
  ],
  "activate_air_filtration": [
    "1"
  ],
  "enable_overhang_bridge_fan": [
    "1"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "during_print_exhaust_fan_speed": [
    "80"
  ],
  "complete_print_exhaust_fan_speed": [
    "100"
  ],
  "name": "Blocks Generic PA-CF"
}

Version history

View full history with diffs →

v1 created 2026-05-19 13:07