Blocks Generic PETG

Generic · PETG · by anycubic-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_petg

→

Blocks Generic PETG

Compatible printers (14)

BLOCKS Pro S100
BLOCKS Pro S100 0.4 nozzle
BLOCKS Pro S100 0.6 nozzle
BLOCKS Pro S100 0.8 nozzle
BLOCKS Pro S100 1.0 nozzle
BLOCKS Pro S100 1.2 nozzle
BLOCKS RD50 V2
BLOCKS RD50 V2 0.4 nozzle
BLOCKS RD50 V2 0.6 nozzle
BLOCKS RD50 V2 0.8 nozzle
BLOCKS RF50
BLOCKS RF50 0.4 nozzle
BLOCKS RF50 0.6 nozzle
BLOCKS RF50 0.8 nozzle

Settings

Basic information

Material variant: PETG inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.24 overridden
was 1.24 (inherited)
Cost (/kg): 30 inherited

Print temperature

Nozzle (initial layer) (°C): 250 overridden
was 245 (inherited)
Nozzle (other layers) (°C): 245 overridden
was 240 (inherited)

Cooling

Fan minimum (%): 40 overridden
was 20 (inherited)
Fan maximum (%): 80 overridden
was 80 (inherited)
Disable fan for first N layers: 1 overridden
was 1 (inherited)
Full fan if layer below (sec): 30 overridden
was 30 (inherited)
Slow down if layer below (sec): 5 overridden
was 5 (inherited)
Min speed when slowed (mm/s): 30 overridden
was 30 (inherited)

Flow

Flow ratio: 0.94 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 12 overridden
was 20 (inherited)

Retraction

Retraction length (mm): 1.0 inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	70 inherited	70 inherited
Engineering Plate	70 inherited	70 inherited
High Temp Plate	70 overridden was 70	70 overridden was 70
Textured PEI Plate	70 inherited	70 inherited

Other settings

activate air filtration: 1 overridden
additional cooling fan speed: 40 overridden
was 0 (inherited)
bed type: Cool Plate inherited
compatible printers: BLOCKS Pro S100 0.4 nozzle, BLOCKS Pro S100 0.6 nozzle, BLOCKS Pro S100 0.8 nozzle, BLOCKS Pro S100 1.0 nozzle, BLOCKS Pro S100 1.2 nozzle, BLOCKS Pro S100, BLOCKS RD50 V2 0.4 nozzle, BLOCKS RD50 V2 0.6 nozzle, BLOCKS RD50 V2 0.8 nozzle, BLOCKS RD50 V2, BLOCKS RF50 0.4 nozzle, BLOCKS RF50 0.6 nozzle, BLOCKS RF50 0.8 nozzle, BLOCKS RF50 overridden
complete print exhaust fan speed: 80 overridden
during print exhaust fan speed: 100 overridden
enable overhang bridge fan: 1 overridden
filament id: BSFI002 overridden
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament shrink: 99.9% overridden
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: 0.0 inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 270 overridden
was 255 (inherited)
nozzle temperature range low: 210 overridden
was 210 (inherited)
overhang fan speed: 100% overridden
was 70 (inherited)
overhang fan threshold: 25% overridden
was 25% (inherited)
reduce fan stop start freq: 1 overridden
was 1 (inherited)
setting id: BSSI002 overridden
slow down for layer cooling: 1 overridden
was 1 (inherited)
temperature vitrification: 70 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "80"
  ],
  "fan_min_speed": [
    "40"
  ],
  "filament_cost": [
    "30"
  ],
  "filament_type": [
    "PETG"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "70"
  ],
  "filament_z_hop": [
    "0.0"
  ],
  "hot_plate_temp": [
    "70"
  ],
  "cool_plate_temp": [
    "70"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "245"
  ],
  "overhang_fan_speed": [
    "100%"
  ],
  "filament_flow_ratio": [
    "0.94"
  ],
  "slow_down_min_speed": [
    "30"
  ],
  "textured_plate_temp": [
    "70"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "5"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "70"
  ],
  "filament_retraction_length": [
    "1.0"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "70"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "70"
  ],
  "cool_plate_temp_initial_layer": [
    "70"
  ],
  "filament_max_volumetric_speed": [
    "12"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "250"
  ],
  "textured_plate_temp_initial_layer": [
    "70"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "40"
  ],
  "nozzle_temperature_range_low": [
    "210"
  ],
  "nozzle_temperature_range_high": [
    "270"
  ],
  "setting_id": "BSSI002",
  "filament_id": "BSFI002",
  "filament_shrink": [
    "99.9%"
  ],
  "compatible_printers": [
    "BLOCKS Pro S100 0.4 nozzle",
    "BLOCKS Pro S100 0.6 nozzle",
    "BLOCKS Pro S100 0.8 nozzle",
    "BLOCKS Pro S100 1.0 nozzle",
    "BLOCKS Pro S100 1.2 nozzle",
    "BLOCKS Pro S100",
    "BLOCKS RD50 V2 0.4 nozzle",
    "BLOCKS RD50 V2 0.6 nozzle",
    "BLOCKS RD50 V2 0.8 nozzle",
    "BLOCKS RD50 V2",
    "BLOCKS RF50 0.4 nozzle",
    "BLOCKS RF50 0.6 nozzle",
    "BLOCKS RF50 0.8 nozzle",
    "BLOCKS RF50"
  ],
  "activate_air_filtration": [
    "1"
  ],
  "enable_overhang_bridge_fan": [
    "1"
  ],
  "during_print_exhaust_fan_speed": [
    "100"
  ],
  "complete_print_exhaust_fan_speed": [
    "80"
  ],
  "name": "Blocks Generic PETG"
}

Version history

View full history with diffs →

v1 created 2026-05-19 13:07