Prusa Generic ASA @CORE One

Prusa · ASA · by anycubic-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Strip G-code from download

Compare

Inheritance

fdm_filament_common

→

fdm_filament_asa

→

Prusa Generic ASA @CORE One

Compatible printers (4)

Prusa CORE One 0.25 nozzle
Prusa CORE One 0.3 nozzle
Prusa CORE One 0.4 nozzle
Prusa CORE One 0.5 nozzle

Inherited from this (6)

Settings

Basic information

Material variant: ASA overridden
was ASA (inherited)
Vendor: Prusa Polymers overridden
was Generic (inherited)
Diameter (mm): 1.75 overridden
was 1.75 (inherited)
Density (g/cm³): 1.07 overridden
was 1.24 (inherited)
Cost (/kg): 35.28 overridden
was 30 (inherited)

Print temperature

Nozzle (initial layer) (°C): 260 overridden
was 260 (inherited)
Nozzle (other layers) (°C): 260 overridden
was 250 (inherited)
Chamber (°C): 40 overridden

Cooling

Fan minimum (%): 20 overridden
was 10 (inherited)
Fan maximum (%): 25 overridden
was 60 (inherited)
Disable fan for first N layers: 4 overridden
was 1 (inherited)
Full fan if layer below (sec): 20 overridden
was 35 (inherited)
Slow down if layer below (sec): 10 overridden
was 3 (inherited)
Min speed when slowed (mm/s): 15 overridden
was 30 (inherited)

Flow

Flow ratio: 1 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 15 overridden
was 20 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	105 inherited	105 inherited
Engineering Plate	105 inherited	105 inherited
High Temp Plate	110 overridden was 105	110 overridden was 105
Textured PEI Plate	105 inherited	105 inherited

Custom G-code

filament_start_gcode overridden

M900 K{if nozzle_diameter[filament_extruder_id]==0.4}0.04{elsif nozzle_diameter[filament_extruder_id]==0.25}0.1{elsif nozzle_diameter[filament_extruder_id]==0.3}0.06{elsif nozzle_diameter[filament_extruder_id]==0.35}0.05{elsif nozzle_diameter[filament_extruder_id]==0.5}0.03{elsif nozzle_diameter[filament_extruder_id]==0.6}0.02{elsif nozzle_diameter[filament_extruder_id]==0.8}0.01{else}0{endif} ; Filament gcode

{if printer_notes=~/.*(MK4IS|XLIS|MK4S|MK3.9S|CORE One).*/}
M572 S{if nozzle_diameter[filament_extruder_id]==0.4}0.02{elsif nozzle_diameter[filament_extruder_id]==0.5}0.018{elsif nozzle_diameter[filament_extruder_id]==0.6}0.012{elsif nozzle_diameter[filament_extruder_id]==0.8}0.01{elsif nozzle_diameter[filament_extruder_id]==0.25}0.09{elsif nozzle_diameter[filament_extruder_id]==0.3}0.065{else}0{endif} ; Filament gcode
{endif}

M142 S40 ; set heatbreak target temp

Other settings

additional cooling fan speed: 0 inherited
bed type: Cool Plate inherited
compatible printers: Prusa CORE One 0.25 nozzle, Prusa CORE One 0.3 nozzle, Prusa CORE One 0.4 nozzle, Prusa CORE One 0.5 nozzle overridden
filament id: Prusa Generic ASA @CORE One overridden
filament minimal purge on wipe tower: 35 overridden
was 15 (inherited)
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 overridden
was 0 (inherited)
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
idle temperature: 130 overridden
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 270 inherited
nozzle temperature range low: 240 inherited
overhang fan speed: 25 overridden
was 80 (inherited)
overhang fan threshold: 25% inherited
reduce fan stop start freq: 1 overridden
was 1 (inherited)
setting id: GFSA04 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 110 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "25"
  ],
  "fan_min_speed": [
    "20"
  ],
  "filament_cost": [
    "35.28"
  ],
  "filament_type": [
    "ASA"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "105"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "110"
  ],
  "cool_plate_temp": [
    "105"
  ],
  "filament_vendor": [
    "Prusa Polymers"
  ],
  "filament_density": [
    "1.07"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; Filament-specific end gcode"
  ],
  "nozzle_temperature": [
    "260"
  ],
  "overhang_fan_speed": [
    "25"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "textured_plate_temp": [
    "105"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "M900 K{if nozzle_diameter[filament_extruder_id]==0.4}0.04{elsif nozzle_diameter[filament_extruder_id]==0.25}0.1{elsif nozzle_diameter[filament_extruder_id]==0.3}0.06{elsif nozzle_diameter[filament_extruder_id]==0.35}0.05{elsif nozzle_diameter[filament_extruder_id]==0.5}0.03{elsif nozzle_diameter[filament_extruder_id]==0.6}0.02{elsif nozzle_diameter[filament_extruder_id]==0.8}0.01{else}0{endif} ; Filament gcode\n\n{if printer_notes=~/.*(MK4IS|XLIS|MK4S|MK3.9S|CORE One).*/}\nM572 S{if nozzle_diameter[filament_extruder_id]==0.4}0.02{elsif nozzle_diameter[filament_extruder_id]==0.5}0.018{elsif nozzle_diameter[filament_extruder_id]==0.6}0.012{elsif nozzle_diameter[filament_extruder_id]==0.8}0.01{elsif nozzle_diameter[filament_extruder_id]==0.25}0.09{elsif nozzle_diameter[filament_extruder_id]==0.3}0.065{else}0{endif} ; Filament gcode\n{endif}\n\nM142 S40 ; set heatbreak target temp"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "10"
  ],
  "fan_cooling_layer_time": [
    "20"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "110"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "4"
  ],
  "eng_plate_temp_initial_layer": [
    "105"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "110"
  ],
  "cool_plate_temp_initial_layer": [
    "105"
  ],
  "filament_max_volumetric_speed": [
    "15"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "260"
  ],
  "textured_plate_temp_initial_layer": [
    "105"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "35"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "240"
  ],
  "nozzle_temperature_range_high": [
    "270"
  ],
  "setting_id": "GFSA04",
  "filament_id": "Prusa Generic ASA @CORE One",
  "filament_notes": [
    ""
  ],
  "idle_temperature": [
    "130"
  ],
  "chamber_temperature": [
    "40"
  ],
  "compatible_printers": [
    "Prusa CORE One 0.25 nozzle",
    "Prusa CORE One 0.3 nozzle",
    "Prusa CORE One 0.4 nozzle",
    "Prusa CORE One 0.5 nozzle"
  ],
  "name": "Prusa Generic ASA @CORE One"
}

Version history

View full history with diffs →

v1 created 2026-05-19 13:05