SUNLU PLA Marble @FF AD5M

Sunlu · PLA · by anycubic-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pla

→

SUNLU PLA Marble @base

→

SUNLU PLA Marble @FF AD5M

Compatible printers (9)

Flashforge AD5X 0.4 nozzle
Flashforge AD5X 0.6 nozzle
Flashforge AD5X 0.8 nozzle
Flashforge Adventurer 5M 0.4 Nozzle
Flashforge Adventurer 5M 0.6 Nozzle
Flashforge Adventurer 5M 0.8 Nozzle
Flashforge Adventurer 5M Pro 0.4 Nozzle
Flashforge Adventurer 5M Pro 0.6 Nozzle
Flashforge Adventurer 5M Pro 0.8 Nozzle

Settings

Basic information

Material variant: PLA inherited
Vendor: SUNLU inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.25 inherited
Cost (/kg): 31.99 inherited

Print temperature

Nozzle (initial layer) (°C): 220 inherited
Nozzle (other layers) (°C): 220 inherited

Cooling

Fan minimum (%): 100 inherited
Fan maximum (%): 100 inherited
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 100 inherited
Slow down if layer below (sec): 5 inherited
Min speed when slowed (mm/s): 5 inherited

Flow

Flow ratio: 1.0 inherited
Max volumetric speed (mm³/s): 12 inherited

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	50 inherited	50 inherited
Engineering Plate	50 inherited	50 inherited
High Temp Plate	50 inherited	50 inherited
Textured PEI Plate	50 inherited	50 inherited

Other settings

additional cooling fan speed: 0 inherited
bed type: Cool Plate inherited
compatible printers: Flashforge Adventurer 5M Pro 0.4 Nozzle, Flashforge Adventurer 5M Pro 0.6 Nozzle, Flashforge Adventurer 5M Pro 0.8 Nozzle, Flashforge Adventurer 5M 0.4 Nozzle, Flashforge Adventurer 5M 0.6 Nozzle, Flashforge Adventurer 5M 0.8 Nozzle, Flashforge AD5X 0.4 nozzle, Flashforge AD5X 0.6 nozzle, Flashforge AD5X 0.8 nozzle overridden
enable pressure advance: 1 inherited
filament id: GFSNL06 inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 240 inherited
nozzle temperature range low: 200 inherited
overhang fan speed: 100 inherited
overhang fan threshold: 50% inherited
pressure advance: 0.03 inherited
reduce fan stop start freq: 1 inherited
renamed from: SUNLU Marble PLA @base inherited
setting id: GFSNLS06 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 60 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_cost": [
    "31.99"
  ],
  "filament_type": [
    "PLA"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "50"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "50"
  ],
  "cool_plate_temp": [
    "50"
  ],
  "filament_vendor": [
    "SUNLU"
  ],
  "filament_density": [
    "1.25"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "220"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "1.0"
  ],
  "slow_down_min_speed": [
    "5"
  ],
  "textured_plate_temp": [
    "50"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    ";filament start gcode\n;right_extruder_material: PLA\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "5"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "50%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "60"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "50"
  ],
  "cool_plate_temp_initial_layer": [
    "50"
  ],
  "filament_max_volumetric_speed": [
    "12"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "220"
  ],
  "textured_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "200"
  ],
  "nozzle_temperature_range_high": [
    "240"
  ],
  "filament_id": "GFSNL06",
  "renamed_from": "SUNLU Marble PLA @base",
  "pressure_advance": [
    "0.03"
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "setting_id": "GFSNLS06",
  "compatible_printers": [
    "Flashforge Adventurer 5M Pro 0.4 Nozzle",
    "Flashforge Adventurer 5M Pro 0.6 Nozzle",
    "Flashforge Adventurer 5M Pro 0.8 Nozzle",
    "Flashforge Adventurer 5M 0.4 Nozzle",
    "Flashforge Adventurer 5M 0.6 Nozzle",
    "Flashforge Adventurer 5M 0.8 Nozzle",
    "Flashforge AD5X 0.4 nozzle",
    "Flashforge AD5X 0.6 nozzle",
    "Flashforge AD5X 0.8 nozzle"
  ],
  "name": "SUNLU PLA Marble @FF AD5M"
}

Version history

View full history with diffs →

v1 created 2026-05-19 13:05