Flashforge PA @FF G4P

Generic · PA · by anycubic-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_tpu

→

Flashforge Generic TPU

→

Flashforge PA @FF G4P

Compatible printers (1)

Flashforge Guider4 Pro 0.4 nozzle

Settings

Basic information

Material variant: PA overridden
was TPU (inherited)
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.24 inherited
Cost (/kg): 20 inherited

Print temperature

Nozzle (initial layer) (°C): 280 overridden
was 225 (inherited)
Nozzle (other layers) (°C): 280 overridden
was 225 (inherited)
Chamber (°C): 60 overridden
was 0 (inherited)

Cooling

Fan minimum (%): 30 overridden
was 100 (inherited)
Fan maximum (%): 60 overridden
was 100 (inherited)
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 30 overridden
was 100 (inherited)
Slow down if layer below (sec): 8 inherited
Min speed when slowed (mm/s): 20 inherited

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 8 overridden
was 3.5 (inherited)

Retraction

Retraction length (mm): 1.2 inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	0 overridden was 60	0 overridden was 60
Engineering Plate	100 overridden was 60	100 overridden was 60
High Temp Plate	100 overridden was 45	100 overridden was 45
Textured PEI Plate	100 overridden was 60	100 overridden was 60

Other settings

activate chamber temp control: 1 overridden
additional cooling fan speed: 0 overridden
was 100 (inherited)
bed temperature difference: 10 inherited
bed type: Cool Plate inherited
compatible printers: Flashforge Guider4 Pro 0.4 nozzle overridden
was Flashforge Adventurer 5M 0.4 Nozzle, Flashforge Adventurer 5M 0.6 Nozzle, Flashforge Adventurer 5M 0.8 Nozzle, Flashforge Adventurer 5M Pro 0.4 Nozzle, Flashforge Adventurer 5M Pro 0.6 Nozzle, Flashforge Adventurer 5M Pro 0.8 Nozzle (inherited)
complete print exhaust fan speed: 50 overridden
during print exhaust fan speed: 40 overridden
enable overhang bridge fan: 1 inherited
enable pressure advance: 1 inherited
filament id: GFG99 inherited
filament is support: 0 inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament shrink: 100% inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was true (inherited)
nozzle temperature range high: 300 overridden
was 250 (inherited)
nozzle temperature range low: 260 overridden
was 190 (inherited)
overhang fan speed: 100 inherited
overhang fan threshold: 50% inherited
pressure advance: 0.02 overridden
was 0.035 (inherited)
reduce fan stop start freq: 1 inherited
required nozzle HRC: 0 inherited
setting id: GFSA04 inherited
slow down for layer cooling: 1 inherited
support material interface fan speed: 100 inherited
temperature vitrification: 110 overridden
was 60 (inherited)

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "60"
  ],
  "fan_min_speed": [
    "30"
  ],
  "filament_cost": [
    "20"
  ],
  "filament_type": [
    "PA"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "100"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "100"
  ],
  "cool_plate_temp": [
    "0"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "280"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "textured_plate_temp": [
    "100"
  ],
  "filament_settings_id": [
    "Flashforge PA @FF G4P"
  ],
  "filament_start_gcode": [
    "; filament start gcode\n;right_extruder_material:PA\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "8"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "50%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "110"
  ],
  "filament_retraction_length": [
    "1.2"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "100"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "100"
  ],
  "cool_plate_temp_initial_layer": [
    "0"
  ],
  "filament_max_volumetric_speed": [
    "8"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "280"
  ],
  "textured_plate_temp_initial_layer": [
    "100"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "260"
  ],
  "nozzle_temperature_range_high": [
    "300"
  ],
  "setting_id": "GFSA04",
  "filament_id": "GFG99",
  "filament_shrink": [
    "100%"
  ],
  "pressure_advance": [
    "0.02"
  ],
  "compatible_prints": [],
  "chamber_temperature": [
    "60"
  ],
  "compatible_printers": [
    "Flashforge Guider4 Pro 0.4 nozzle"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "0"
  ],
  "default_filament_colour": [
    ""
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "bed_temperature_difference": [
    "10"
  ],
  "enable_overhang_bridge_fan": [
    "1"
  ],
  "compatible_prints_condition": "",
  "compatible_printers_condition": "",
  "support_material_interface_fan_speed": [
    "100"
  ],
  "activate_chamber_temp_control": [
    "1"
  ],
  "during_print_exhaust_fan_speed": [
    "40"
  ],
  "complete_print_exhaust_fan_speed": [
    "50"
  ],
  "name": "Flashforge PA @FF G4P"
}

Version history

View full history with diffs →

v1 created 2026-05-19 13:04