Flashforge Generic PLA-Silk

Volumic · PLA · by anycubic-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pla

→

Flashforge Generic PLA-Silk

Compatible printers (9)

Flashforge AD5X 0.4 nozzle
Flashforge AD5X 0.6 nozzle
Flashforge AD5X 0.8 nozzle
Flashforge Adventurer 5M 0.4 Nozzle
Flashforge Adventurer 5M 0.6 Nozzle
Flashforge Adventurer 5M 0.8 Nozzle
Flashforge Adventurer 5M Pro 0.4 Nozzle
Flashforge Adventurer 5M Pro 0.6 Nozzle
Flashforge Adventurer 5M Pro 0.8 Nozzle

Inherited from this (7)

Settings

Basic information

Material variant: PLA inherited
Vendor: Generic inherited
Diameter (mm): 1.75 overridden
was 1.75 (inherited)
Density (g/cm³): 1.24 inherited
Cost (/kg): 30 inherited

Print temperature

Nozzle (initial layer) (°C): 220 overridden
was 220 (inherited)
Nozzle (other layers) (°C): 220 overridden
was 220 (inherited)

Cooling

Fan minimum (%): 100 inherited
Fan maximum (%): 100 inherited
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 100 inherited
Slow down if layer below (sec): 8 overridden
was 5 (inherited)
Min speed when slowed (mm/s): 20 overridden
was 5 (inherited)

Flow

Flow ratio: 1 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 12 overridden
was 20 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	50 inherited	50 inherited
Engineering Plate	50 inherited	50 inherited
High Temp Plate	55 overridden was 50	50 overridden was 50
Textured PEI Plate	50 inherited	50 inherited

Other settings

additional cooling fan speed: 100 overridden
was 0 (inherited)
bed type: Cool Plate inherited
compatible printers: Flashforge Adventurer 5M 0.4 Nozzle, Flashforge Adventurer 5M 0.6 Nozzle, Flashforge Adventurer 5M 0.8 Nozzle, Flashforge Adventurer 5M Pro 0.4 Nozzle, Flashforge Adventurer 5M Pro 0.6 Nozzle, Flashforge Adventurer 5M Pro 0.8 Nozzle, Flashforge AD5X 0.4 nozzle, Flashforge AD5X 0.6 nozzle, Flashforge AD5X 0.8 nozzle overridden
enable pressure advance: 1 overridden
filament id: GFL99 overridden
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 230 overridden
was 230 (inherited)
nozzle temperature range low: 190 overridden
was 190 (inherited)
overhang fan speed: 100 inherited
overhang fan threshold: 50% inherited
pressure advance: 0.025 overridden
reduce fan stop start freq: 1 inherited
setting id: GFSA04 overridden
slow down for layer cooling: 1 inherited
support material interface fan speed: 100 overridden
temperature vitrification: 60 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_cost": [
    "30"
  ],
  "filament_type": [
    "PLA"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "50"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "50"
  ],
  "cool_plate_temp": [
    "50"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode\n"
  ],
  "nozzle_temperature": [
    "220"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "textured_plate_temp": [
    "50"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n;right_extruder_material: PLA Silk\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "8"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "50%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "60"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "55"
  ],
  "cool_plate_temp_initial_layer": [
    "50"
  ],
  "filament_max_volumetric_speed": [
    "12"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "220"
  ],
  "textured_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "100"
  ],
  "nozzle_temperature_range_low": [
    "190"
  ],
  "nozzle_temperature_range_high": [
    "230"
  ],
  "setting_id": "GFSA04",
  "filament_id": "GFL99",
  "pressure_advance": [
    "0.025"
  ],
  "compatible_printers": [
    "Flashforge Adventurer 5M 0.4 Nozzle",
    "Flashforge Adventurer 5M 0.6 Nozzle",
    "Flashforge Adventurer 5M 0.8 Nozzle",
    "Flashforge Adventurer 5M Pro 0.4 Nozzle",
    "Flashforge Adventurer 5M Pro 0.6 Nozzle",
    "Flashforge Adventurer 5M Pro 0.8 Nozzle",
    "Flashforge AD5X 0.4 nozzle",
    "Flashforge AD5X 0.6 nozzle",
    "Flashforge AD5X 0.8 nozzle"
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "support_material_interface_fan_speed": [
    "100"
  ],
  "name": "Flashforge Generic PLA-Silk"
}

Version history

View full history with diffs →

v1 created 2026-05-19 13:04