Flashforge Generic PETG

Volumic · PETG · by anycubic-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pet

→

Flashforge Generic PETG

Compatible printers (9)

Flashforge AD5X 0.4 nozzle
Flashforge AD5X 0.6 nozzle
Flashforge AD5X 0.8 nozzle
Flashforge Adventurer 5M 0.4 Nozzle
Flashforge Adventurer 5M 0.6 Nozzle
Flashforge Adventurer 5M 0.8 Nozzle
Flashforge Adventurer 5M Pro 0.4 Nozzle
Flashforge Adventurer 5M Pro 0.6 Nozzle
Flashforge Adventurer 5M Pro 0.8 Nozzle

Inherited from this (39)

View all 39 →

Settings

Basic information

Material variant: PETG inherited
Vendor: Generic inherited
Diameter (mm): 1.75 overridden
was 1.75 (inherited)
Density (g/cm³): 1.27 overridden
was 1.27 (inherited)
Cost (/kg): 30 inherited

Print temperature

Nozzle (initial layer) (°C): 255 overridden
was 255 (inherited)
Nozzle (other layers) (°C): 255 overridden
was 255 (inherited)

Cooling

Fan minimum (%): 80 overridden
was 20 (inherited)
Fan maximum (%): 100 overridden
was 80 (inherited)
Disable fan for first N layers: 1 overridden
was 3 (inherited)
Full fan if layer below (sec): 30 overridden
was 5 (inherited)
Slow down if layer below (sec): 8 overridden
was 8 (inherited)
Min speed when slowed (mm/s): 30 overridden
was 10 (inherited)

Flow

Flow ratio: 1 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 12 overridden
was 25 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	60 inherited	60 inherited
Engineering Plate	70 inherited	0 inherited
High Temp Plate	70 overridden was 70	70 overridden was 80
Textured PEI Plate	70 inherited	80 inherited

Other settings

additional cooling fan speed: 50 overridden
bed type: Cool Plate inherited
compatible printers: Flashforge Adventurer 5M 0.4 Nozzle, Flashforge Adventurer 5M 0.6 Nozzle, Flashforge Adventurer 5M 0.8 Nozzle, Flashforge Adventurer 5M Pro 0.4 Nozzle, Flashforge Adventurer 5M Pro 0.6 Nozzle, Flashforge Adventurer 5M Pro 0.8 Nozzle, Flashforge AD5X 0.4 nozzle, Flashforge AD5X 0.6 nozzle, Flashforge AD5X 0.8 nozzle overridden
enable pressure advance: 1 overridden
filament id: GFG99 overridden
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 260 overridden
was 280 (inherited)
nozzle temperature range low: 220 overridden
was 220 (inherited)
overhang fan speed: 80 overridden
was 70 (inherited)
overhang fan threshold: 25% overridden
was 95% (inherited)
pressure advance: 0.046 overridden
reduce fan stop start freq: 1 inherited
setting id: GFSA04 overridden
slow down for layer cooling: 1 inherited
support material interface fan speed: 90 overridden
temperature vitrification: 70 overridden
was 80 (inherited)

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "80"
  ],
  "filament_cost": [
    "30"
  ],
  "filament_type": [
    "PETG"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "0"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "70"
  ],
  "cool_plate_temp": [
    "60"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.27"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode\n"
  ],
  "nozzle_temperature": [
    "255"
  ],
  "overhang_fan_speed": [
    "80"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "30"
  ],
  "textured_plate_temp": [
    "80"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode \n;right_extruder_material:PETG"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "8"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "70"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "70"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "70"
  ],
  "cool_plate_temp_initial_layer": [
    "60"
  ],
  "filament_max_volumetric_speed": [
    "12"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "255"
  ],
  "textured_plate_temp_initial_layer": [
    "70"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "220"
  ],
  "nozzle_temperature_range_high": [
    "260"
  ],
  "setting_id": "GFSA04",
  "filament_id": "GFG99",
  "pressure_advance": [
    "0.046"
  ],
  "compatible_printers": [
    "Flashforge Adventurer 5M 0.4 Nozzle",
    "Flashforge Adventurer 5M 0.6 Nozzle",
    "Flashforge Adventurer 5M 0.8 Nozzle",
    "Flashforge Adventurer 5M Pro 0.4 Nozzle",
    "Flashforge Adventurer 5M Pro 0.6 Nozzle",
    "Flashforge Adventurer 5M Pro 0.8 Nozzle",
    "Flashforge AD5X 0.4 nozzle",
    "Flashforge AD5X 0.6 nozzle",
    "Flashforge AD5X 0.8 nozzle"
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "additional_cooling_fan_speed": [
    "50"
  ],
  "support_material_interface_fan_speed": [
    "90"
  ],
  "name": "Flashforge Generic PETG"
}

Version history

View full history with diffs →

v1 created 2026-05-19 13:04