Flashforge Generic PETG-CF10

Generic · PETG-CF · by anycubic-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pet

→

Flashforge Generic PETG-CF10

Compatible printers (6)

Flashforge Adventurer 5M 0.4 Nozzle
Flashforge Adventurer 5M 0.6 Nozzle
Flashforge Adventurer 5M 0.8 Nozzle
Flashforge Adventurer 5M Pro 0.4 Nozzle
Flashforge Adventurer 5M Pro 0.6 Nozzle
Flashforge Adventurer 5M Pro 0.8 Nozzle

Inherited from this (5)

Settings

Basic information

Material variant: PETG-CF overridden
was PETG (inherited)
Vendor: Generic overridden
was Generic (inherited)
Diameter (mm): 1.75 overridden
was 1.75 (inherited)
Density (g/cm³): 1.27 overridden
was 1.27 (inherited)
Cost (/kg): 30 overridden
was 30 (inherited)

Print temperature

Nozzle (initial layer) (°C): 245 overridden
was 255 (inherited)
Nozzle (other layers) (°C): 245 overridden
was 255 (inherited)
Chamber (°C): 0 overridden

Cooling

Fan minimum (%): 80 overridden
was 20 (inherited)
Fan maximum (%): 100 overridden
was 80 (inherited)
Disable fan for first N layers: 1 overridden
was 3 (inherited)
Full fan if layer below (sec): 30 overridden
was 5 (inherited)
Slow down if layer below (sec): 8 overridden
was 8 (inherited)
Min speed when slowed (mm/s): 20 overridden
was 10 (inherited)

Flow

Flow ratio: 1 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 12 overridden
was 25 (inherited)

Retraction

Retraction length (mm): nil overridden
was nil (inherited)
Retraction speed (mm/s): nil overridden
was nil (inherited)
Deretraction speed (mm/s): nil overridden
was nil (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	60 overridden was 60	60 overridden was 60
Engineering Plate	60 overridden was 70	60 overridden was 0
High Temp Plate	70 overridden was 70	70 overridden was 80
Textured PEI Plate	60 overridden was 70	60 overridden was 80

Other settings

additional cooling fan speed: 100 overridden
bed temperature difference: 10 overridden
bed type: Cool Plate inherited
compatible printers: Flashforge Adventurer 5M 0.4 Nozzle, Flashforge Adventurer 5M 0.6 Nozzle, Flashforge Adventurer 5M 0.8 Nozzle, Flashforge Adventurer 5M Pro 0.4 Nozzle, Flashforge Adventurer 5M Pro 0.6 Nozzle, Flashforge Adventurer 5M Pro 0.8 Nozzle overridden
enable overhang bridge fan: 1 overridden
enable pressure advance: 1 overridden
filament id: GFG99 overridden
filament is support: 0 overridden
filament minimal purge on wipe tower: 15 overridden
was 15 (inherited)
filament retract before wipe: nil overridden
was nil (inherited)
filament retract restart extra: nil overridden
was nil (inherited)
filament retract when changing layer: nil overridden
was nil (inherited)
filament retraction minimum travel: nil overridden
was nil (inherited)
filament shrink: 100% overridden
filament soluble: 0 overridden
was 0 (inherited)
filament wipe: nil overridden
was nil (inherited)
filament wipe distance: nil overridden
was nil (inherited)
filament z hop: nil overridden
was nil (inherited)
filament z hop types: nil overridden
was nil (inherited)
full fan speed layer: 0 overridden
was 0 (inherited)
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 260 overridden
was 280 (inherited)
nozzle temperature range low: 220 overridden
was 220 (inherited)
overhang fan speed: 90 overridden
was 70 (inherited)
overhang fan threshold: 25% overridden
was 95% (inherited)
pressure advance: 0.035 overridden
reduce fan stop start freq: 1 overridden
was 1 (inherited)
required nozzle HRC: 0 overridden
setting id: GFSA04 overridden
slow down for layer cooling: 1 overridden
was 1 (inherited)
support material interface fan speed: 100 overridden
temperature vitrification: 70 overridden
was 80 (inherited)

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "80"
  ],
  "filament_cost": [
    "30"
  ],
  "filament_type": [
    "PETG-CF"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "60"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "70"
  ],
  "cool_plate_temp": [
    "60"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.27"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "245"
  ],
  "overhang_fan_speed": [
    "90"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "textured_plate_temp": [
    "60"
  ],
  "filament_settings_id": [
    "Flashforge PETG-CF10"
  ],
  "filament_start_gcode": [
    "; filament start gcode\n;right_extruder_material:PETG-CF10\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "8"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "70"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "60"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "70"
  ],
  "cool_plate_temp_initial_layer": [
    "60"
  ],
  "filament_max_volumetric_speed": [
    "12"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "245"
  ],
  "textured_plate_temp_initial_layer": [
    "60"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "220"
  ],
  "nozzle_temperature_range_high": [
    "260"
  ],
  "setting_id": "GFSA04",
  "filament_id": "GFG99",
  "filament_shrink": [
    "100%"
  ],
  "pressure_advance": [
    "0.035"
  ],
  "compatible_prints": [],
  "chamber_temperature": "0",
  "compatible_printers": [
    "Flashforge Adventurer 5M 0.4 Nozzle",
    "Flashforge Adventurer 5M 0.6 Nozzle",
    "Flashforge Adventurer 5M 0.8 Nozzle",
    "Flashforge Adventurer 5M Pro 0.4 Nozzle",
    "Flashforge Adventurer 5M Pro 0.6 Nozzle",
    "Flashforge Adventurer 5M Pro 0.8 Nozzle"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "0"
  ],
  "default_filament_colour": [
    ""
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "bed_temperature_difference": [
    "10"
  ],
  "enable_overhang_bridge_fan": [
    "1"
  ],
  "compatible_prints_condition": "",
  "additional_cooling_fan_speed": [
    "100"
  ],
  "compatible_printers_condition": "",
  "support_material_interface_fan_speed": [
    "100"
  ],
  "name": "Flashforge Generic PETG-CF10"
}

Version history

View full history with diffs →

v1 created 2026-05-19 13:03