Polymaker PETG Polymax black P1 @iQ TiQ2 0.4 Nozzle

iQ Materials · PETG POLYMAX · 0.40mm nozzle · by anycubic-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Strip G-code from download

Compare

Inheritance

fdm_filament_common

→

Polymaker PETG Polymax black P1 @iQ TiQ2 0.4 Nozzle

Compatible printers (1)

iQ TiQ2 0.4 Nozzle

Settings

Basic information

Material variant: PETG Polymax overridden
was PLA (inherited)
Vendor: iQ Materials overridden
was Generic (inherited)
Diameter (mm): 1.75 overridden
was 1.75 (inherited)
Density (g/cm³): 1.25 overridden
was 0 (inherited)
Cost (/kg): 29.99 overridden
was 0 (inherited)

Print temperature

Nozzle (initial layer) (°C): 250 overridden
was 200 (inherited)
Nozzle (other layers) (°C): 250 overridden
was 200 (inherited)
Chamber (°C): 0 overridden

Cooling

Fan minimum (%): 100 overridden
was 35 (inherited)
Fan maximum (%): 100 overridden
was 100 (inherited)
Disable fan for first N layers: 3 overridden
was 3 (inherited)
Full fan if layer below (sec): 100 overridden
was 60 (inherited)
Slow down if layer below (sec): 8 overridden
was 8 (inherited)
Min speed when slowed (mm/s): 10 overridden
was 10 (inherited)

Flow

Flow ratio: 0.9405 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 12 overridden
was 0 (inherited)

Retraction

Retraction length (mm): 0.2 overridden
was nil (inherited)
Retraction speed (mm/s): nil overridden
was nil (inherited)
Deretraction speed (mm/s): nil overridden
was nil (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	0 overridden was 60	0 overridden was 60
Textured Cool Plate	40 overridden	40 overridden
Engineering Plate	60 overridden was 60	60 overridden was 60
High Temp Plate	80 overridden was 60	80 overridden was 60
Textured PEI Plate	60 overridden was 60	60 overridden was 60
Cool Plate SuperTack	70 overridden	70 overridden

Custom G-code

filament_start_gcode overridden

; Filament gcode
G1 X-17 Y1 F9000
G1 Y45 F9000
G1 Y1 F9000
G1 Y45 F9000
{if layer_z==0}G1 Z{first_layer_height + 2.0}{endif}
{if layer_z==0}G1 X[first_layer_print_min_0] Y[first_layer_print_min_1]{endif}
{if layer_z==0}G1 Z{layer_z}{endif}

filament_end_gcode overridden

; filament end gcode 
G1 Z{layer_z+2} F900 ; safe distance for T0 while tool change
G1 X-17 Y1 F9000
G1 X-17 Y45 F9000
G1 Y1 F9000
G1 Y45 F9000

Other settings

activate air filtration: 0 overridden
activate chamber temp control: 0 overridden
adaptive pressure advance: 0 overridden
adaptive pressure advance bridges: 0 overridden
adaptive pressure advance model: 0,0,0 0,0,0 overridden
adaptive pressure advance overhangs: 0 overridden
additional cooling fan speed: 0 overridden
bed type: Cool Plate inherited
compatible printers: iQ TiQ2 0.4 Nozzle overridden
compatible prints: 0.20mm Standard @iQ TiQ2 P1 - PETG Polymax Polymaker (0.4 Nozzle) overridden
complete print exhaust fan speed: 70 overridden
default filament colour: #000000 overridden
dont slow down outer wall: 0 overridden
during print exhaust fan speed: 70 overridden
enable overhang bridge fan: 0 overridden
enable pressure advance: 0 overridden
filament cooling final speed: 3.4 overridden
filament cooling initial speed: 2.2 overridden
filament cooling moves: 4 overridden
filament id: IQM3 overridden
filament is support: 0 overridden
filament loading speed: 28 overridden
filament loading speed start: 3 overridden
filament long retractions when cut: nil overridden
filament minimal purge on wipe tower: 15 overridden
was 15 (inherited)
filament multitool ramming: 0 overridden
filament multitool ramming flow: 10 overridden
filament multitool ramming volume: 10 overridden
filament ramming parameters: 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 overridden
filament retract before wipe: nil overridden
was nil (inherited)
filament retract lift above: nil overridden
filament retract lift below: nil overridden
filament retract lift enforce: nil overridden
filament retract restart extra: nil overridden
was nil (inherited)
filament retract when changing layer: nil overridden
was nil (inherited)
filament retraction distances when cut: nil overridden
filament retraction minimum travel: nil overridden
was nil (inherited)
filament shrink: 100% overridden
filament shrinkage compensation z: 100% overridden
filament soluble: 0 overridden
was 0 (inherited)
filament stamping distance: 0 overridden
filament stamping loading speed: 0 overridden
filament toolchange delay: 0 overridden
filament unloading speed: 90 overridden
filament unloading speed start: 100 overridden
filament wipe: nil overridden
was nil (inherited)
filament wipe distance: nil overridden
was nil (inherited)
filament z hop: nil overridden
was nil (inherited)
filament z hop types: nil overridden
was nil (inherited)
full fan speed layer: 0 overridden
was 0 (inherited)
idle temperature: 210 overridden
instantiation: true overridden
was false (inherited)
internal bridge fan speed: -1 overridden
ironing fan speed: -1 overridden
nozzle temperature range high: 240 overridden
nozzle temperature range low: 230 overridden
overhang fan speed: 100 overridden
was 100 (inherited)
overhang fan threshold: 95% overridden
was 95% (inherited)
pellet flow coefficient: 0.4157 overridden
pressure advance: 0.02 overridden
reduce fan stop start freq: 1 overridden
was 0 (inherited)
required nozzle HRC: 3 overridden
settings id: IQS3 overridden
slow down for layer cooling: 1 overridden
was 1 (inherited)
support material interface fan speed: -1 overridden
temperature vitrification: 76 overridden
was 100 (inherited)

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_cost": [
    "29.99"
  ],
  "filament_type": [
    "PETG Polymax"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "60"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "80"
  ],
  "cool_plate_temp": [
    "0"
  ],
  "filament_vendor": [
    "iQ Materials"
  ],
  "filament_density": [
    "1.25"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \nG1 Z{layer_z+2} F900 ; safe distance for T0 while tool change\nG1 X-17 Y1 F9000\nG1 X-17 Y45 F9000\nG1 Y1 F9000\nG1 Y45 F9000"
  ],
  "nozzle_temperature": [
    "250"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "0.9405"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "textured_plate_temp": [
    "60"
  ],
  "filament_settings_id": [
    "Polymaker PETG Polymax black P1 @iQ TiQ2 0.4 Nozzle"
  ],
  "filament_start_gcode": [
    "; Filament gcode\nG1 X-17 Y1 F9000\nG1 Y45 F9000\nG1 Y1 F9000\nG1 Y45 F9000\n{if layer_z==0}G1 Z{first_layer_height + 2.0}{endif}\n{if layer_z==0}G1 X[first_layer_print_min_0] Y[first_layer_print_min_1]{endif}\n{if layer_z==0}G1 Z{layer_z}{endif}"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "8"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "95%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "76"
  ],
  "filament_retraction_length": [
    "0.2"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "60"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "80"
  ],
  "cool_plate_temp_initial_layer": [
    "0"
  ],
  "filament_max_volumetric_speed": [
    "12"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "250"
  ],
  "textured_plate_temp_initial_layer": [
    "60"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "filament_id": "IQM3",
  "settings_id": "IQS3",
  "filament_notes": [
    ""
  ],
  "filament_shrink": [
    "100%"
  ],
  "idle_temperature": [
    "210"
  ],
  "pressure_advance": [
    "0.02"
  ],
  "compatible_prints": [
    "0.20mm Standard @iQ TiQ2 P1 - PETG Polymax Polymaker (0.4 Nozzle)"
  ],
  "ironing_fan_speed": [
    "-1"
  ],
  "chamber_temperature": [
    "0"
  ],
  "compatible_printers": [
    "iQ TiQ2 0.4 Nozzle"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "3"
  ],
  "supertack_plate_temp": [
    "70"
  ],
  "filament_cooling_moves": [
    "4"
  ],
  "filament_loading_speed": [
    "28"
  ],
  "activate_air_filtration": [
    "0"
  ],
  "default_filament_colour": [
    "#000000"
  ],
  "enable_pressure_advance": [
    "0"
  ],
  "pellet_flow_coefficient": [
    "0.4157"
  ],
  "filament_unloading_speed": [
    "90"
  ],
  "textured_cool_plate_temp": [
    "40"
  ],
  "adaptive_pressure_advance": [
    "0"
  ],
  "dont_slow_down_outer_wall": [
    "0"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "internal_bridge_fan_speed": [
    "-1"
  ],
  "enable_overhang_bridge_fan": [
    "0"
  ],
  "filament_multitool_ramming": [
    "0"
  ],
  "filament_stamping_distance": [
    "0"
  ],
  "compatible_prints_condition": "",
  "filament_ramming_parameters": [
    "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "filament_retract_lift_above": [
    "nil"
  ],
  "filament_retract_lift_below": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "filament_cooling_final_speed": [
    "3.4"
  ],
  "filament_loading_speed_start": [
    "3"
  ],
  "nozzle_temperature_range_low": [
    "230"
  ],
  "activate_chamber_temp_control": [
    "0"
  ],
  "compatible_printers_condition": "",
  "filament_retract_lift_enforce": [
    "nil"
  ],
  "nozzle_temperature_range_high": [
    "240"
  ],
  "during_print_exhaust_fan_speed": [
    "70"
  ],
  "filament_cooling_initial_speed": [
    "2.2"
  ],
  "filament_unloading_speed_start": [
    "100"
  ],
  "adaptive_pressure_advance_model": [
    "0,0,0\n0,0,0"
  ],
  "filament_multitool_ramming_flow": [
    "10"
  ],
  "filament_stamping_loading_speed": [
    "0"
  ],
  "complete_print_exhaust_fan_speed": [
    "70"
  ],
  "adaptive_pressure_advance_bridges": [
    "0"
  ],
  "filament_multitool_ramming_volume": [
    "10"
  ],
  "filament_shrinkage_compensation_z": [
    "100%"
  ],
  "filament_long_retractions_when_cut": [
    "nil"
  ],
  "supertack_plate_temp_initial_layer": [
    "70"
  ],
  "adaptive_pressure_advance_overhangs": [
    "0"
  ],
  "support_material_interface_fan_speed": [
    "-1"
  ],
  "filament_retraction_distances_when_cut": [
    "nil"
  ],
  "textured_cool_plate_temp_initial_layer": [
    "40"
  ],
  "name": "Polymaker PETG Polymax black P1 @iQ TiQ2 0.4 Nozzle"
}

Version history

View full history with diffs →

v1 created 2026-05-19 13:03