Cubicon PA-CF @base

Cubicon · PA · by orca-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pa

→

Cubicon PA-CF @base

Compatible printers (2)

Cubicon xCeler-I 0.4 nozzle
Cubicon xCeler-Plus 0.4 nozzle

Inherited from this (2)

Settings

Basic information

Material variant: PA overridden
was PA (inherited)
Vendor: Cubicon overridden
was Generic (inherited)
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.24 overridden
was 1.04 (inherited)
Cost (/kg): 20 inherited

Print temperature

Nozzle (initial layer) (°C): 265 overridden
was 270 (inherited)
Nozzle (other layers) (°C): 270 overridden
was 270 (inherited)

Cooling

Fan minimum (%): 50 overridden
was 0 (inherited)
Fan maximum (%): 50 overridden
was 60 (inherited)
Disable fan for first N layers: 3 overridden
was 3 (inherited)
Full fan if layer below (sec): 5 overridden
was 10 (inherited)
Slow down if layer below (sec): 2 overridden
was 2 (inherited)
Min speed when slowed (mm/s): 20 overridden
was 10 (inherited)

Flow

Flow ratio: 0.99 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 10 overridden
was 8 (inherited)

Retraction

Retraction length (mm): 1.0 inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	0 inherited	0 inherited
Engineering Plate	100 inherited	100 inherited
High Temp Plate	100 overridden was 100	100 overridden was 100
Textured PEI Plate	100 inherited	100 inherited

Other settings

additional cooling fan speed: 0 overridden
bed type: Cool Plate inherited
compatible printers: Cubicon xCeler-I 0.4 nozzle, Cubicon xCeler-Plus 0.4 nozzle overridden
filament id: P510cfd0 overridden
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: 0.0 inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 280 overridden
was 300 (inherited)
nozzle temperature range low: 260 overridden
was 260 (inherited)
overhang fan speed: 60 inherited
overhang fan threshold: 95% inherited
reduce fan stop start freq: 0 inherited
slow down for layer cooling: 1 inherited
temperature vitrification: 108 overridden
was 108 (inherited)

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "50"
  ],
  "fan_min_speed": [
    "50"
  ],
  "filament_cost": [
    "20"
  ],
  "filament_type": [
    "PA"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "100"
  ],
  "filament_z_hop": [
    "0.0"
  ],
  "hot_plate_temp": [
    "100"
  ],
  "cool_plate_temp": [
    "0"
  ],
  "filament_vendor": [
    "Cubicon"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "270"
  ],
  "overhang_fan_speed": [
    "60"
  ],
  "filament_flow_ratio": [
    "0.99"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "textured_plate_temp": [
    "100"
  ],
  "filament_settings_id": [
    "Cubicon PA-CF @base"
  ],
  "filament_start_gcode": [
    "; Filament gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "2"
  ],
  "fan_cooling_layer_time": [
    "5"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "95%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "108"
  ],
  "filament_retraction_length": [
    "1.0"
  ],
  "reduce_fan_stop_start_freq": [
    "0"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "100"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "100"
  ],
  "cool_plate_temp_initial_layer": [
    "0"
  ],
  "filament_max_volumetric_speed": [
    "10"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "265"
  ],
  "textured_plate_temp_initial_layer": [
    "100"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "260"
  ],
  "nozzle_temperature_range_high": [
    "280"
  ],
  "filament_id": "P510cfd0",
  "compatible_printers": [
    "Cubicon xCeler-I 0.4 nozzle",
    "Cubicon xCeler-Plus 0.4 nozzle"
  ],
  "default_filament_colour": "",
  "additional_cooling_fan_speed": [
    "0"
  ],
  "name": "Cubicon PA-CF @base"
}

Version history

View full history with diffs →

v1 created 2026-05-19 04:32