Valment PLA Silk @System

Valment · PLA · by anycubic-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pla

→

Valment PLA Silk @base

→

Valment PLA Silk @System

Settings

Basic information

Material variant: PLA inherited
Vendor: Valment inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.24 inherited
Cost (/kg): 710 inherited

Print temperature

Nozzle (initial layer) (°C): 245 inherited
Nozzle (other layers) (°C): 240 inherited

Cooling

Fan minimum (%): 100 inherited
Fan maximum (%): 100 inherited
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 100 inherited
Slow down if layer below (sec): 6 inherited
Min speed when slowed (mm/s): 20 inherited

Flow

Flow ratio: 0.98 inherited
Max volumetric speed (mm³/s): 7.5 inherited

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	50 inherited	50 inherited
Engineering Plate	50 inherited	50 inherited
High Temp Plate	50 inherited	50 inherited
Textured PEI Plate	50 inherited	50 inherited

Other settings

additional cooling fan speed: 100 inherited
bed type: Cool Plate inherited
complete print exhaust fan speed: 80 inherited
default filament colour: #124943 inherited
during print exhaust fan speed: 60 inherited
filament id: VLMNT02 inherited
filament minimal purge on wipe tower: 15 inherited
filament notes: Bu filament ayarları GlauTech tarafından oluşturulmuştur. Filamentin daha verimli çalışması için, slicerdaki kalibrasyon ayarlarının tek tek yapılması önemlidir. Kalibrasyon ayarları için, GlauTech youtube kanalından destek alabilirsiniz. Boş Makara Ağırlığı: 150gr inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 250 inherited
nozzle temperature range low: 220 inherited
overhang fan speed: 100 inherited
overhang fan threshold: 50% inherited
reduce fan stop start freq: 1 inherited
setting id: VLMNT_02 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 60 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_cost": [
    "710"
  ],
  "filament_type": [
    "PLA"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "50"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "50"
  ],
  "cool_plate_temp": [
    "50"
  ],
  "filament_vendor": [
    "Valment"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "240"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "0.98"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "textured_plate_temp": [
    "50"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "6"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "50%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "60"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "50"
  ],
  "cool_plate_temp_initial_layer": [
    "50"
  ],
  "filament_max_volumetric_speed": [
    "7.5"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "245"
  ],
  "textured_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "100"
  ],
  "nozzle_temperature_range_low": [
    "220"
  ],
  "nozzle_temperature_range_high": [
    "250"
  ],
  "filament_id": "VLMNT02",
  "filament_notes": [
    "Bu filament ayarlar\u0131 GlauTech taraf\u0131ndan olu\u015fturulmu\u015ftur. Filamentin daha verimli \u00e7al\u0131\u015fmas\u0131 i\u00e7in, slicerdaki kalibrasyon ayarlar\u0131n\u0131n tek tek yap\u0131lmas\u0131 \u00f6nemlidir. Kalibrasyon ayarlar\u0131 i\u00e7in, GlauTech youtube kanal\u0131ndan destek alabilirsiniz.\n\nBo\u015f Makara A\u011f\u0131rl\u0131\u011f\u0131: 150gr"
  ],
  "default_filament_colour": [
    "#124943"
  ],
  "during_print_exhaust_fan_speed": [
    "60"
  ],
  "complete_print_exhaust_fan_speed": [
    "80"
  ],
  "setting_id": "VLMNT_02",
  "compatible_printers": [],
  "name": "Valment PLA Silk @System"
}

Version history

View full history with diffs →

v1 created 2026-05-19 13:02