Chuanying ASA @Chuanying X1 0.25 Nozzle

Generic · ASA · by anycubic-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_asa

→

Chuanying Generic ASA

→

Chuanying ASA @Chuanying X1 0.25 Nozzle

Compatible printers (1)

Chuanying X1 0.25 Nozzle

Settings

Basic information

Material variant: ASA inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.04 inherited
Cost (/kg): 40 overridden
was 20 (inherited)

Print temperature

Nozzle (initial layer) (°C): 260 inherited
Nozzle (other layers) (°C): 260 inherited
Chamber (°C): 0 inherited

Cooling

Fan minimum (%): 10 inherited
Fan maximum (%): 50 overridden
was 20 (inherited)
Disable fan for first N layers: 2 inherited
Full fan if layer below (sec): 30 inherited
Slow down if layer below (sec): 5 inherited
Min speed when slowed (mm/s): 20 inherited

Flow

Flow ratio: 1 overridden
was 0.98 (inherited)
Max volumetric speed (mm³/s): 2 overridden
was 18 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	60 inherited	60 inherited
Engineering Plate	60 inherited	60 inherited
High Temp Plate	105 inherited	105 inherited
Textured PEI Plate	60 inherited	60 inherited

Other settings

additional cooling fan speed: 0 inherited
bed temperature difference: 10 inherited
bed type: Cool Plate inherited
compatible printers: Chuanying X1 0.25 Nozzle overridden
was Chuanying X1 0.4 Nozzle, Chuanying X1 0.6 Nozzle, Chuanying X1 0.8 Nozzle (inherited)
enable overhang bridge fan: 1 inherited
enable pressure advance: 1 inherited
filament id: GFL99 overridden
was GFL99 (inherited)
filament is support: 0 inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament shrink: 100% inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was true (inherited)
nozzle temperature range high: 270 inherited
nozzle temperature range low: 230 inherited
overhang fan speed: 80 inherited
overhang fan threshold: 25% inherited
pressure advance: 0.1 overridden
was 0.04 (inherited)
reduce fan stop start freq: 1 inherited
required nozzle HRC: 0 inherited
setting id: GFSA04_05 overridden
was GFSA04 (inherited)
slow down for layer cooling: 1 inherited
support material interface fan speed: 80 inherited
temperature vitrification: 100 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "50"
  ],
  "fan_min_speed": [
    "10"
  ],
  "filament_cost": [
    "40"
  ],
  "filament_type": [
    "ASA"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "60"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "105"
  ],
  "cool_plate_temp": [
    "60"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.04"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode\n"
  ],
  "nozzle_temperature": [
    "260"
  ],
  "overhang_fan_speed": [
    "80"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "textured_plate_temp": [
    "60"
  ],
  "filament_settings_id": [
    "Chuanying ASA @Chuanying X1 0.25 Nozzle"
  ],
  "filament_start_gcode": [
    "; filament start gcode\n;right_extruder_material: ASA\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "5"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "100"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "2"
  ],
  "eng_plate_temp_initial_layer": [
    "60"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "105"
  ],
  "cool_plate_temp_initial_layer": [
    "60"
  ],
  "filament_max_volumetric_speed": [
    "2"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "260"
  ],
  "textured_plate_temp_initial_layer": [
    "60"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "230"
  ],
  "nozzle_temperature_range_high": [
    "270"
  ],
  "setting_id": "GFSA04_05",
  "filament_id": "GFL99",
  "filament_shrink": [
    "100%"
  ],
  "pressure_advance": [
    "0.1"
  ],
  "compatible_prints": [],
  "chamber_temperature": "0",
  "compatible_printers": [
    "Chuanying X1 0.25 Nozzle"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "0"
  ],
  "default_filament_colour": [
    ""
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "bed_temperature_difference": [
    "10"
  ],
  "enable_overhang_bridge_fan": [
    "1"
  ],
  "compatible_prints_condition": "",
  "compatible_printers_condition": "",
  "support_material_interface_fan_speed": [
    "80"
  ],
  "name": "Chuanying ASA @Chuanying X1 0.25 Nozzle"
}

Version history

View full history with diffs →

v1 created 2026-05-19 13:01