fdm_filament_pet @S1

FlyingBear · PETG · by anycubic-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common_S1

→

fdm_filament_pet @S1

Inherited from this (1)

FlyingBear PETG @S1

Settings

Basic information

Material variant: PETG overridden
was PLA (inherited)
Vendor: FlyingBear overridden
was Generic (inherited)
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.27 overridden
was 0 (inherited)
Cost (/kg): 30 overridden
was 0 (inherited)

Print temperature

Nozzle (initial layer) (°C): 245 overridden
was 200 (inherited)
Nozzle (other layers) (°C): 245 overridden
was 200 (inherited)

Cooling

Fan minimum (%): 40 overridden
was 35 (inherited)
Fan maximum (%): 90 overridden
was 100 (inherited)
Disable fan for first N layers: 3 overridden
was 3 (inherited)
Full fan if layer below (sec): 30 overridden
was 60 (inherited)
Slow down if layer below (sec): 8 inherited
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 12 overridden
was 0 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	60 overridden was 60	60 overridden was 60
Engineering Plate	0 overridden was 60	0 overridden was 60
High Temp Plate	75 overridden was 60	75 overridden was 60
Textured PEI Plate	80 overridden was 60	80 overridden was 60

Other settings

additional cooling fan speed: 0 overridden
bed type: Cool Plate inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: false overridden
was false (inherited)
nozzle temperature range high: 280 overridden
nozzle temperature range low: 200 overridden
overhang fan speed: 90 overridden
was 100 (inherited)
overhang fan threshold: 0% inherited
reduce fan stop start freq: 1 overridden
was 0 (inherited)
slow down for layer cooling: 1 overridden
was 1 (inherited)
temperature vitrification: 80 overridden
was 100 (inherited)

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "90"
  ],
  "fan_min_speed": [
    "40"
  ],
  "filament_cost": [
    "30"
  ],
  "filament_type": [
    "PETG"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "false",
  "eng_plate_temp": [
    "0"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "75"
  ],
  "cool_plate_temp": [
    "60"
  ],
  "filament_vendor": [
    "FlyingBear"
  ],
  "filament_density": [
    "1.27"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "245"
  ],
  "overhang_fan_speed": [
    "90"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "textured_plate_temp": [
    "80"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "8"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "0%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "80"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "0"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "75"
  ],
  "cool_plate_temp_initial_layer": [
    "60"
  ],
  "filament_max_volumetric_speed": [
    "12"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "245"
  ],
  "textured_plate_temp_initial_layer": [
    "80"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "200"
  ],
  "nozzle_temperature_range_high": [
    "280"
  ],
  "name": "fdm_filament_pet @S1"
}

Version history

View full history with diffs →

v1 created 2026-05-19 13:00