WonderMaker PETG Basic

WonderMaker · PETG · by anycubic-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pet

→

WonderMaker PETG Basic

Compatible printers (12)

WonderMaker ZR 0.2 nozzle
WonderMaker ZR 0.4 nozzle
WonderMaker ZR 0.6 nozzle
WonderMaker ZR 0.8 nozzle
WonderMaker ZR Ultra 0.2 nozzle
WonderMaker ZR Ultra 0.4 nozzle
WonderMaker ZR Ultra 0.6 nozzle
WonderMaker ZR Ultra 0.8 nozzle
WonderMaker ZR Ultra S 0.2 nozzle
WonderMaker ZR Ultra S 0.4 nozzle
WonderMaker ZR Ultra S 0.6 nozzle
WonderMaker ZR Ultra S 0.8 nozzle

Settings

Basic information

Material variant: PETG inherited
Vendor: WonderMaker overridden
was Generic (inherited)
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.25 overridden
was 1.27 (inherited)
Cost (/kg): 24.99 overridden
was 30 (inherited)

Print temperature

Nozzle (initial layer) (°C): 255 inherited
Nozzle (other layers) (°C): 255 inherited

Cooling

Fan minimum (%): 10 overridden
was 20 (inherited)
Fan maximum (%): 40 overridden
was 80 (inherited)
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 30 overridden
was 5 (inherited)
Slow down if layer below (sec): 12 overridden
was 8 (inherited)
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 0.95 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 8 overridden
was 25 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	0 overridden was 60	0 overridden was 60
Engineering Plate	70 overridden was 70	70 overridden was 0
High Temp Plate	70 overridden was 70	70 overridden was 80
Textured PEI Plate	70 overridden was 70	70 overridden was 80

Other settings

bed type: Cool Plate inherited
compatible printers: WonderMaker ZR 0.2 nozzle, WonderMaker ZR 0.4 nozzle, WonderMaker ZR 0.6 nozzle, WonderMaker ZR 0.8 nozzle, WonderMaker ZR Ultra 0.2 nozzle, WonderMaker ZR Ultra 0.4 nozzle, WonderMaker ZR Ultra 0.6 nozzle, WonderMaker ZR Ultra 0.8 nozzle, WonderMaker ZR Ultra S 0.2 nozzle, WonderMaker ZR Ultra S 0.4 nozzle, WonderMaker ZR Ultra S 0.6 nozzle, WonderMaker ZR Ultra S 0.8 nozzle overridden
description: To get better transparent or translucent results with the corresponding filament, please refer to this wiki: Printing tips for transparent PETG. overridden
filament id: GFG00 overridden
filament minimal purge on wipe tower: 15 inherited
filament multitool ramming: 1 overridden
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 270 overridden
was 280 (inherited)
nozzle temperature range low: 230 overridden
was 220 (inherited)
overhang fan speed: 90 overridden
was 70 (inherited)
overhang fan threshold: 10% overridden
was 95% (inherited)
reduce fan stop start freq: 1 inherited
slow down for layer cooling: 1 inherited
temperature vitrification: 80 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "40"
  ],
  "fan_min_speed": [
    "10"
  ],
  "filament_cost": [
    "24.99"
  ],
  "filament_type": [
    "PETG"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "70"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "70"
  ],
  "cool_plate_temp": [
    "0"
  ],
  "filament_vendor": [
    "WonderMaker"
  ],
  "filament_density": [
    "1.25"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "255"
  ],
  "overhang_fan_speed": [
    "90"
  ],
  "filament_flow_ratio": [
    "0.95"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "textured_plate_temp": [
    "70"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "12"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "10%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "80"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "70"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "70"
  ],
  "cool_plate_temp_initial_layer": [
    "0"
  ],
  "filament_max_volumetric_speed": [
    "8"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "255"
  ],
  "textured_plate_temp_initial_layer": [
    "70"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "230"
  ],
  "nozzle_temperature_range_high": [
    "270"
  ],
  "description": "To get better transparent or translucent results with the corresponding filament, please refer to this wiki: Printing tips for transparent PETG.",
  "filament_id": "GFG00",
  "compatible_printers": [
    "WonderMaker ZR 0.2 nozzle",
    "WonderMaker ZR 0.4 nozzle",
    "WonderMaker ZR 0.6 nozzle",
    "WonderMaker ZR 0.8 nozzle",
    "WonderMaker ZR Ultra 0.2 nozzle",
    "WonderMaker ZR Ultra 0.4 nozzle",
    "WonderMaker ZR Ultra 0.6 nozzle",
    "WonderMaker ZR Ultra 0.8 nozzle",
    "WonderMaker ZR Ultra S 0.2 nozzle",
    "WonderMaker ZR Ultra S 0.4 nozzle",
    "WonderMaker ZR Ultra S 0.6 nozzle",
    "WonderMaker ZR Ultra S 0.8 nozzle"
  ],
  "filament_multitool_ramming": [
    "1"
  ],
  "name": "WonderMaker PETG Basic"
}

Version history

View full history with diffs →

v1 created 2026-05-19 13:00