WonderMaker PLA Matte

WonderMaker · OTHER · by anycubic-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pla

→

WonderMaker PLA Matte

Compatible printers (12)

WonderMaker ZR 0.2 nozzle
WonderMaker ZR 0.4 nozzle
WonderMaker ZR 0.6 nozzle
WonderMaker ZR 0.8 nozzle
WonderMaker ZR Ultra 0.2 nozzle
WonderMaker ZR Ultra 0.4 nozzle
WonderMaker ZR Ultra 0.6 nozzle
WonderMaker ZR Ultra 0.8 nozzle
WonderMaker ZR Ultra S 0.2 nozzle
WonderMaker ZR Ultra S 0.4 nozzle
WonderMaker ZR Ultra S 0.6 nozzle
WonderMaker ZR Ultra S 0.8 nozzle

Settings

Basic information

Material variant: PLA inherited
Vendor: WonderMaker overridden
was Generic (inherited)
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.32 overridden
was 1.24 (inherited)
Cost (/kg): 24.99 overridden
was 30 (inherited)

Print temperature

Nozzle (initial layer) (°C): 220 inherited
Nozzle (other layers) (°C): 220 inherited

Cooling

Fan minimum (%): 100 inherited
Fan maximum (%): 100 inherited
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 100 inherited
Slow down if layer below (sec): 5 inherited
Min speed when slowed (mm/s): 5 inherited

Flow

Flow ratio: 0.98 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 20 inherited

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	50 inherited	50 inherited
Engineering Plate	50 inherited	50 inherited
High Temp Plate	50 inherited	50 inherited
Textured PEI Plate	50 inherited	50 inherited

Other settings

additional cooling fan speed: 0 inherited
bed type: Cool Plate inherited
compatible printers: WonderMaker ZR 0.2 nozzle, WonderMaker ZR 0.4 nozzle, WonderMaker ZR 0.6 nozzle, WonderMaker ZR 0.8 nozzle, WonderMaker ZR Ultra 0.2 nozzle, WonderMaker ZR Ultra 0.4 nozzle, WonderMaker ZR Ultra 0.6 nozzle, WonderMaker ZR Ultra 0.8 nozzle, WonderMaker ZR Ultra S 0.2 nozzle, WonderMaker ZR Ultra S 0.4 nozzle, WonderMaker ZR Ultra S 0.6 nozzle, WonderMaker ZR Ultra S 0.8 nozzle overridden
filament id: GFA01 overridden
filament minimal purge on wipe tower: 15 inherited
filament multitool ramming: 1 overridden
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament scarf gap: 0% overridden
filament scarf height: 5% overridden
filament scarf length: 10 overridden
filament scarf seam type: none overridden
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 230 inherited
nozzle temperature range low: 190 inherited
overhang fan speed: 100 inherited
overhang fan threshold: 50% inherited
reduce fan stop start freq: 1 inherited
slow down for layer cooling: 1 inherited
temperature vitrification: 60 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_cost": [
    "24.99"
  ],
  "filament_type": [
    "PLA"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "50"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "50"
  ],
  "cool_plate_temp": [
    "50"
  ],
  "filament_vendor": [
    "WonderMaker"
  ],
  "filament_density": [
    "1.32"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "220"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "0.98"
  ],
  "slow_down_min_speed": [
    "5"
  ],
  "textured_plate_temp": [
    "50"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "5"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "50%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "60"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "50"
  ],
  "cool_plate_temp_initial_layer": [
    "50"
  ],
  "filament_max_volumetric_speed": [
    "20"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "220"
  ],
  "textured_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "190"
  ],
  "nozzle_temperature_range_high": [
    "230"
  ],
  "filament_id": "GFA01",
  "filament_scarf_gap": [
    "0%"
  ],
  "compatible_printers": [
    "WonderMaker ZR 0.2 nozzle",
    "WonderMaker ZR 0.4 nozzle",
    "WonderMaker ZR 0.6 nozzle",
    "WonderMaker ZR 0.8 nozzle",
    "WonderMaker ZR Ultra 0.2 nozzle",
    "WonderMaker ZR Ultra 0.4 nozzle",
    "WonderMaker ZR Ultra 0.6 nozzle",
    "WonderMaker ZR Ultra 0.8 nozzle",
    "WonderMaker ZR Ultra S 0.2 nozzle",
    "WonderMaker ZR Ultra S 0.4 nozzle",
    "WonderMaker ZR Ultra S 0.6 nozzle",
    "WonderMaker ZR Ultra S 0.8 nozzle"
  ],
  "filament_scarf_height": [
    "5%"
  ],
  "filament_scarf_length": [
    "10"
  ],
  "filament_scarf_seam_type": [
    "none"
  ],
  "filament_multitool_ramming": [
    "1"
  ],
  "name": "WonderMaker PLA Matte"
}

Version history

View full history with diffs →

v1 created 2026-05-19 13:00