WonderMaker PVA

WonderMaker · PVA · by anycubic-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pva

→

WonderMaker PVA

Compatible printers (12)

WonderMaker ZR 0.2 nozzle
WonderMaker ZR 0.4 nozzle
WonderMaker ZR 0.6 nozzle
WonderMaker ZR 0.8 nozzle
WonderMaker ZR Ultra 0.2 nozzle
WonderMaker ZR Ultra 0.4 nozzle
WonderMaker ZR Ultra 0.6 nozzle
WonderMaker ZR Ultra 0.8 nozzle
WonderMaker ZR Ultra S 0.2 nozzle
WonderMaker ZR Ultra S 0.4 nozzle
WonderMaker ZR Ultra S 0.6 nozzle
WonderMaker ZR Ultra S 0.8 nozzle

Settings

Basic information

Material variant: PVA inherited
Vendor: WonderMaker overridden
was Generic (inherited)
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.27 overridden
was 1.24 (inherited)
Cost (/kg): 79.98 overridden
was 20 (inherited)

Print temperature

Nozzle (initial layer) (°C): 220 inherited
Nozzle (other layers) (°C): 220 inherited

Cooling

Fan minimum (%): 100 inherited
Fan maximum (%): 100 inherited
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 100 inherited
Slow down if layer below (sec): 7 overridden
was 4 (inherited)
Min speed when slowed (mm/s): 20 overridden
was 10 (inherited)

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 6 overridden
was 15 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	35 inherited	35 inherited
Engineering Plate	0 inherited	0 inherited
High Temp Plate	45 inherited	45 inherited
Textured PEI Plate	45 inherited	45 inherited

Other settings

additional cooling fan speed: 70 inherited
bed type: Cool Plate inherited
compatible printers: WonderMaker ZR 0.2 nozzle, WonderMaker ZR 0.4 nozzle, WonderMaker ZR 0.6 nozzle, WonderMaker ZR 0.8 nozzle, WonderMaker ZR Ultra 0.2 nozzle, WonderMaker ZR Ultra 0.4 nozzle, WonderMaker ZR Ultra 0.6 nozzle, WonderMaker ZR Ultra 0.8 nozzle, WonderMaker ZR Ultra S 0.2 nozzle, WonderMaker ZR Ultra S 0.4 nozzle, WonderMaker ZR Ultra S 0.6 nozzle, WonderMaker ZR Ultra S 0.8 nozzle overridden
description: This is a water-soluble support filament, and usually it is only for the support structure and not for the model body. Printing this filament is of many requirements, and to get better printing quality, please refer to this wiki: PVA Printing Guide. overridden
filament id: GFS04 overridden
filament is support: 1 inherited
filament minimal purge on wipe tower: 15 inherited
filament multitool ramming: 1 overridden
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 1 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 250 overridden
was 250 (inherited)
nozzle temperature range low: 210 overridden
was 190 (inherited)
overhang fan speed: 100 inherited
overhang fan threshold: 50% inherited
reduce fan stop start freq: 1 inherited
slow down for layer cooling: 1 inherited
temperature vitrification: 50 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_cost": [
    "79.98"
  ],
  "filament_type": [
    "PVA"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "0"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "45"
  ],
  "cool_plate_temp": [
    "35"
  ],
  "filament_vendor": [
    "WonderMaker"
  ],
  "filament_density": [
    "1.27"
  ],
  "filament_soluble": [
    "1"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "220"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "textured_plate_temp": [
    "45"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "7"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "50%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "50"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "0"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "45"
  ],
  "cool_plate_temp_initial_layer": [
    "35"
  ],
  "filament_max_volumetric_speed": [
    "6"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "220"
  ],
  "textured_plate_temp_initial_layer": [
    "45"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "filament_is_support": [
    "1"
  ],
  "additional_cooling_fan_speed": [
    "70"
  ],
  "nozzle_temperature_range_low": [
    "210"
  ],
  "nozzle_temperature_range_high": [
    "250"
  ],
  "description": "This is a water-soluble support filament, and usually it is only for the support structure and not for the model body. Printing this filament is of many requirements, and to get better printing quality, please refer to this wiki: PVA Printing Guide.",
  "filament_id": "GFS04",
  "compatible_printers": [
    "WonderMaker ZR 0.2 nozzle",
    "WonderMaker ZR 0.4 nozzle",
    "WonderMaker ZR 0.6 nozzle",
    "WonderMaker ZR 0.8 nozzle",
    "WonderMaker ZR Ultra 0.2 nozzle",
    "WonderMaker ZR Ultra 0.4 nozzle",
    "WonderMaker ZR Ultra 0.6 nozzle",
    "WonderMaker ZR Ultra 0.8 nozzle",
    "WonderMaker ZR Ultra S 0.2 nozzle",
    "WonderMaker ZR Ultra S 0.4 nozzle",
    "WonderMaker ZR Ultra S 0.6 nozzle",
    "WonderMaker ZR Ultra S 0.8 nozzle"
  ],
  "filament_multitool_ramming": [
    "1"
  ],
  "name": "WonderMaker PVA"
}

Version history

View full history with diffs →

v1 created 2026-05-19 13:00