Snapmaker J1 ASA @0.2 nozzle

Generic · ASA · 0.20mm nozzle · by anycubic-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_asa

→

Snapmaker J1 ASA @base

→

Snapmaker J1 ASA @0.2 nozzle

Compatible printers (1)

Snapmaker J1 (0.2 nozzle)

Settings

Basic information

Material variant: ASA inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.24 inherited
Cost (/kg): 30 inherited

Print temperature

Nozzle (initial layer) (°C): 260 inherited
Nozzle (other layers) (°C): 250 inherited

Cooling

Fan minimum (%): 10 overridden
was 0 (inherited)
Fan maximum (%): 35 overridden
was 20 (inherited)
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 35 inherited
Slow down if layer below (sec): 3 inherited
Min speed when slowed (mm/s): 30 inherited

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 2.4 overridden
was 9.6 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	105 inherited	105 inherited
Engineering Plate	105 inherited	105 inherited
High Temp Plate	90 overridden was 100	90 overridden was 110
Textured PEI Plate	105 inherited	105 inherited

Other settings

additional cooling fan speed: 0 inherited
bed type: Cool Plate inherited
compatible printers: Snapmaker J1 (0.2 nozzle) overridden
filament id: 144877656 inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 270 inherited
nozzle temperature range low: 240 inherited
overhang fan speed: 80 overridden
was 20 (inherited)
overhang fan threshold: 25% inherited
reduce fan stop start freq: 1 inherited
setting id: 924839906 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 110 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "35"
  ],
  "fan_min_speed": [
    "10"
  ],
  "filament_cost": [
    "30"
  ],
  "filament_type": [
    "ASA"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "105"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "90"
  ],
  "cool_plate_temp": [
    "105"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "250"
  ],
  "overhang_fan_speed": [
    "80"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "30"
  ],
  "textured_plate_temp": [
    "105"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "3"
  ],
  "fan_cooling_layer_time": [
    "35"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "110"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "105"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "90"
  ],
  "cool_plate_temp_initial_layer": [
    "105"
  ],
  "filament_max_volumetric_speed": [
    "2.4"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "260"
  ],
  "textured_plate_temp_initial_layer": [
    "105"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "240"
  ],
  "nozzle_temperature_range_high": [
    "270"
  ],
  "filament_id": "144877656",
  "setting_id": "924839906",
  "compatible_printers": [
    "Snapmaker J1 (0.2 nozzle)"
  ],
  "name": "Snapmaker J1 ASA @0.2 nozzle"
}

Version history

View full history with diffs →

v1 created 2026-05-19 13:00