Snapmaker ASA @U1 base

Generic · ASA · by anycubic-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_asa

→

Snapmaker ASA @U1 base

Inherited from this (1)

Snapmaker ASA @U1

Settings

Basic information

Material variant: ASA inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.24 inherited
Cost (/kg): 30 inherited

Print temperature

Nozzle (initial layer) (°C): 260 inherited
Nozzle (other layers) (°C): 250 inherited

Cooling

Fan minimum (%): 0 overridden
was 10 (inherited)
Fan maximum (%): 15 overridden
was 60 (inherited)
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 35 inherited
Slow down if layer below (sec): 3 inherited
Min speed when slowed (mm/s): 30 inherited

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 8 overridden
was 20 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	105 inherited	105 inherited
Engineering Plate	105 inherited	105 inherited
High Temp Plate	100 overridden was 105	110 overridden was 105
Textured PEI Plate	105 inherited	105 inherited

Other settings

additional cooling fan speed: 0 inherited
bed type: Cool Plate inherited
filament cooling final speed: 60 overridden
filament cooling initial speed: 35 overridden
filament cooling moves: 2 overridden
filament id: 12471727060 overridden
filament load time: 2 overridden
filament loading speed: 35 overridden
filament loading speed start: 35 overridden
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament unload time: 2 overridden
filament unloading speed: 35 overridden
filament unloading speed start: 35 overridden
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: false overridden
was false (inherited)
nozzle temperature range high: 270 inherited
nozzle temperature range low: 240 inherited
overhang fan speed: 15 overridden
was 80 (inherited)
overhang fan threshold: 25% inherited
reduce fan stop start freq: 1 inherited
slow down for layer cooling: 1 inherited
temperature vitrification: 110 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "15"
  ],
  "fan_min_speed": [
    "0"
  ],
  "filament_cost": [
    "30"
  ],
  "filament_type": [
    "ASA"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "false",
  "eng_plate_temp": [
    "105"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "110"
  ],
  "cool_plate_temp": [
    "105"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    ""
  ],
  "nozzle_temperature": [
    "250"
  ],
  "overhang_fan_speed": [
    "15"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "30"
  ],
  "textured_plate_temp": [
    "105"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "3"
  ],
  "fan_cooling_layer_time": [
    "35"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "110"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "105"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "100"
  ],
  "cool_plate_temp_initial_layer": [
    "105"
  ],
  "filament_max_volumetric_speed": [
    "8"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "260"
  ],
  "textured_plate_temp_initial_layer": [
    "105"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "240"
  ],
  "nozzle_temperature_range_high": [
    "270"
  ],
  "filament_id": "12471727060",
  "filament_load_time": [
    "2"
  ],
  "filament_unload_time": [
    "2"
  ],
  "filament_cooling_moves": [
    "2"
  ],
  "filament_loading_speed": [
    "35"
  ],
  "filament_unloading_speed": [
    "35"
  ],
  "filament_cooling_final_speed": [
    "60"
  ],
  "filament_loading_speed_start": [
    "35"
  ],
  "filament_cooling_initial_speed": [
    "35"
  ],
  "filament_unloading_speed_start": [
    "35"
  ],
  "name": "Snapmaker ASA @U1 base"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:59