Tiertime PVA@300HS

Tiertime · PVA · by anycubic-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pva

→

Tiertime PVA@300HS

Compatible printers (4)

Tiertime UP300 HS 0.4 nozzle
Tiertime UP600 HS 0.4 nozzle
Tiertime UP600 HS 0.6 nozzle
Tiertime UP600 HS 0.8 nozzle

Settings

Basic information

Material variant: PVA inherited
Vendor: Tiertime overridden
was Generic (inherited)
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.27 overridden
was 1.24 (inherited)
Cost (/kg): 79.98 overridden
was 20 (inherited)

Print temperature

Nozzle (initial layer) (°C): 240 overridden
was 220 (inherited)
Nozzle (other layers) (°C): 240 overridden
was 220 (inherited)

Cooling

Fan minimum (%): 100 inherited
Fan maximum (%): 100 inherited
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 100 inherited
Slow down if layer below (sec): 7 overridden
was 4 (inherited)
Min speed when slowed (mm/s): 20 overridden
was 10 (inherited)

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 6 overridden
was 15 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	35 inherited	35 inherited
Engineering Plate	0 inherited	0 inherited
High Temp Plate	45 inherited	45 inherited
Textured PEI Plate	45 inherited	45 inherited

Other settings

additional cooling fan speed: 70 inherited
bed type: Cool Plate inherited
compatible printers: Tiertime UP300 HS 0.4 nozzle, Tiertime UP600 HS 0.4 nozzle, Tiertime UP600 HS 0.6 nozzle, Tiertime UP600 HS 0.8 nozzle overridden
filament id: GFS04_01 overridden
filament is support: 1 inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 1 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 250 overridden
was 250 (inherited)
nozzle temperature range low: 210 overridden
was 190 (inherited)
overhang fan speed: 100 inherited
overhang fan threshold: 50% inherited
reduce fan stop start freq: 1 inherited
slow down for layer cooling: 1 inherited
temperature vitrification: 50 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_cost": [
    "79.98"
  ],
  "filament_type": [
    "PVA"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "0"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "45"
  ],
  "cool_plate_temp": [
    "35"
  ],
  "filament_vendor": [
    "Tiertime"
  ],
  "filament_density": [
    "1.27"
  ],
  "filament_soluble": [
    "1"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "240"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "textured_plate_temp": [
    "45"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "7"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "50%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "50"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "0"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "45"
  ],
  "cool_plate_temp_initial_layer": [
    "35"
  ],
  "filament_max_volumetric_speed": [
    "6"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "240"
  ],
  "textured_plate_temp_initial_layer": [
    "45"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "filament_is_support": [
    "1"
  ],
  "additional_cooling_fan_speed": [
    "70"
  ],
  "nozzle_temperature_range_low": [
    "210"
  ],
  "nozzle_temperature_range_high": [
    "250"
  ],
  "filament_id": "GFS04_01",
  "compatible_printers": [
    "Tiertime UP300 HS 0.4 nozzle",
    "Tiertime UP600 HS 0.4 nozzle",
    "Tiertime UP600 HS 0.6 nozzle",
    "Tiertime UP600 HS 0.8 nozzle"
  ],
  "name": "Tiertime PVA@300HS"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:59