SUNLU PETG @BBL A1M 0.8 nozzle

Sunlu · PETG · 0.80mm nozzle · by anycubic-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pet

→

SUNLU PETG @base

→

SUNLU PETG @BBL X1C 0.8 nozzle

→

SUNLU PETG @BBL A1M 0.8 nozzle

Compatible printers (2)

Bambu Lab A1 mini 0.6 nozzle
Bambu Lab A1 mini 0.8 nozzle

Settings

Basic information

Material variant: PETG inherited
Vendor: SUNLU inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.27 inherited
Cost (/kg): 22.99 inherited

Print temperature

Nozzle (initial layer) (°C): 250 inherited
Nozzle (other layers) (°C): 245 inherited

Cooling

Fan minimum (%): 20 inherited
Fan maximum (%): 60 inherited
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 30 inherited
Slow down if layer below (sec): 12 inherited
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 0.94 overridden
was 0.98 (inherited)
Max volumetric speed (mm³/s): 12 overridden
was 16 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	0 inherited	0 inherited
Engineering Plate	60 inherited	60 inherited
High Temp Plate	60 inherited	60 inherited
Textured PEI Plate	60 inherited	60 inherited

Other settings

bed type: Cool Plate inherited
compatible printers: Bambu Lab A1 mini 0.6 nozzle, Bambu Lab A1 mini 0.8 nozzle overridden
was Bambu Lab X1 Carbon 0.6 nozzle, Bambu Lab X1 0.6 nozzle, Bambu Lab P1P 0.6 nozzle, Bambu Lab X1 Carbon 0.8 nozzle, Bambu Lab X1 0.8 nozzle, Bambu Lab P1P 0.8 nozzle, Bambu Lab P1S 0.6 nozzle, Bambu Lab P1S 0.8 nozzle, Bambu Lab X1E 0.6 nozzle, Bambu Lab X1E 0.8 nozzle (inherited)
description: To get better transparent or translucent results with the corresponding filament, please refer to this wiki: Printing tips for transparent PETG. inherited
enable pressure advance: 1 inherited
filament id: GFSNL08 inherited
filament long retractions when cut: nil overridden
was 1 (inherited)
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction distances when cut: nil overridden
was 18 (inherited)
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was true (inherited)
nozzle temperature range high: 280 inherited
nozzle temperature range low: 230 inherited
overhang fan speed: 90 inherited
overhang fan threshold: 10% inherited
pressure advance: 0.046 inherited
reduce fan stop start freq: 1 inherited
setting id: GFSNLS08_07 overridden
was GFSNLS08_01 (inherited)
slow down for layer cooling: 1 inherited
temperature vitrification: 68 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "60"
  ],
  "fan_min_speed": [
    "20"
  ],
  "filament_cost": [
    "22.99"
  ],
  "filament_type": [
    "PETG"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "60"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "60"
  ],
  "cool_plate_temp": [
    "0"
  ],
  "filament_vendor": [
    "SUNLU"
  ],
  "filament_density": [
    "1.27"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "245"
  ],
  "overhang_fan_speed": [
    "90"
  ],
  "filament_flow_ratio": [
    "0.94"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "textured_plate_temp": [
    "60"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    ";filament start gcode\n;right_extruder_material: PETG\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "12"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "10%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "68"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "60"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "60"
  ],
  "cool_plate_temp_initial_layer": [
    "0"
  ],
  "filament_max_volumetric_speed": [
    "12"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "250"
  ],
  "textured_plate_temp_initial_layer": [
    "60"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "230"
  ],
  "nozzle_temperature_range_high": [
    "280"
  ],
  "description": "To get better transparent or translucent results with the corresponding filament, please refer to this wiki: Printing tips for transparent PETG.",
  "filament_id": "GFSNL08",
  "pressure_advance": [
    "0.046"
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "setting_id": "GFSNLS08_07",
  "compatible_printers": [
    "Bambu Lab A1 mini 0.6 nozzle",
    "Bambu Lab A1 mini 0.8 nozzle"
  ],
  "filament_long_retractions_when_cut": [
    "nil"
  ],
  "filament_retraction_distances_when_cut": [
    "nil"
  ],
  "name": "SUNLU PETG @BBL A1M 0.8 nozzle"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:56