TwoTrees Generic 95A TPU @SK1

Generic · TPU · by anycubic-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_tpu

→

TwoTrees Generic 95A TPU @SK1

Compatible printers (1)

TwoTrees SK1 0.4 nozzle

Settings

Basic information

Material variant: TPU inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.24 inherited
Cost (/kg): 35 inherited

Print temperature

Nozzle (initial layer) (°C): 235 overridden
was 235 (inherited)
Nozzle (other layers) (°C): 235 overridden
was 235 (inherited)

Cooling

Fan minimum (%): 35 overridden
was 100 (inherited)
Fan maximum (%): 100 overridden
was 100 (inherited)
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 60 overridden
was 100 (inherited)
Slow down if layer below (sec): 5 overridden
was 5 (inherited)
Min speed when slowed (mm/s): 10 overridden
was 5 (inherited)

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 15 overridden
was 15 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	40 inherited	40 inherited
Engineering Plate	40 inherited	40 inherited
High Temp Plate	40 inherited	40 inherited
Textured PEI Plate	50 inherited	40 inherited

Other settings

additional cooling fan speed: 0 inherited
bed type: Cool Plate inherited
compatible printers: TwoTrees SK1 0.4 nozzle overridden
filament id: GFU99 overridden
filament minimal purge on wipe tower: 15 overridden
was 15 (inherited)
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 overridden
was 0 (inherited)
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 250 inherited
nozzle temperature range low: 210 inherited
overhang fan speed: 100 inherited
overhang fan threshold: 50% inherited
reduce fan stop start freq: 0 overridden
was 1 (inherited)
setting id: GFSU99 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 50 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": "100",
  "fan_min_speed": "35",
  "filament_cost": [
    "35"
  ],
  "filament_type": [
    "TPU"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "40"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "40"
  ],
  "cool_plate_temp": [
    "40"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": "235",
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": "10",
  "textured_plate_temp": [
    "40"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": "0",
  "slow_down_layer_time": "5",
  "fan_cooling_layer_time": "60",
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "50%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "50"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": "0",
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "40"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "40"
  ],
  "cool_plate_temp_initial_layer": [
    "40"
  ],
  "filament_max_volumetric_speed": "15",
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": "235",
  "textured_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": "15",
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "210"
  ],
  "nozzle_temperature_range_high": [
    "250"
  ],
  "setting_id": "GFSU99",
  "filament_id": "GFU99",
  "compatible_printers": [
    "TwoTrees SK1 0.4 nozzle"
  ],
  "name": "TwoTrees Generic 95A TPU @SK1"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:53