Creality Generic PLA @K2-all

QIDI · PLA · by anycubic-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Strip G-code from download

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pla

→

Creality Generic PLA

→

Creality Generic PLA @K2-all

Compatible printers (4)

Creality K2 Plus 0.2 nozzle
Creality K2 Plus 0.4 nozzle
Creality K2 Plus 0.6 nozzle
Creality K2 Plus 0.8 nozzle

Inherited from this (3)

Settings

Basic information

Material variant: PLA inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.24 inherited
Cost (/kg): 30 inherited

Print temperature

Nozzle (initial layer) (°C): 220 inherited
Nozzle (other layers) (°C): 220 inherited

Cooling

Fan minimum (%): 100 inherited
Fan maximum (%): 100 inherited
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 100 inherited
Slow down if layer below (sec): 4 overridden
was 8 (inherited)
Min speed when slowed (mm/s): 20 overridden
was 5 (inherited)

Flow

Flow ratio: 0.95 overridden
was 0.98 (inherited)
Max volumetric speed (mm³/s): 18 overridden
was 12 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	50 overridden was 50	50 overridden was 50
Engineering Plate	50 overridden was 50	50 overridden was 50
High Temp Plate	50 overridden was 50	50 overridden was 50
Textured PEI Plate	50 overridden was 50	50 overridden was 50

Custom G-code

filament_start_gcode overridden

; filament start gcode
{if (position[2] > first_layer_height) }
M104 S[nozzle_temperature]
{else}
M104 S[first_layer_temperature]
{endif}

{if(initial_extruder != current_extruder || position[2] > first_layer_height)}
{if (position[2] +0.4  < printable_height) }
G2 Z{position[2]  + 0.4} I0.86 J0.86 P1 F10000 ; spiral lift a little from second lift
G1 X205 Y345 F20000
G1 Z{position[2] } F1200
{else}
G1 X205 Y345 F20000
{endif}
{endif}

Other settings

additional cooling fan speed: 0 inherited
bed type: Cool Plate inherited
compatible printers: Creality K2 Plus 0.2 nozzle, Creality K2 Plus 0.4 nozzle, Creality K2 Plus 0.6 nozzle, Creality K2 Plus 0.8 nozzle overridden
was Creality CR-10 V2 0.4 nozzle, Creality CR-10 V3 0.4 nozzle, Creality CR-10 V3 0.6 nozzle, Creality CR-10 Max 0.4 nozzle, Creality CR-6 SE 0.2 nozzle, Creality CR-6 SE 0.4 nozzle, Creality CR-6 SE 0.6 nozzle, Creality CR-6 SE 0.8 nozzle, Creality CR-6 Max 0.2 nozzle, Creality CR-6 Max 0.4 nozzle, Creality CR-6 Max 0.6 nozzle, Creality CR-6 Max 0.8 nozzle, Creality Sermoon V1 0.4 nozzle, Creality Ender-3 0.2 nozzle, Creality Ender-3 0.4 nozzle, Creality Ender-3 0.6 nozzle, Creality Ender-3 0.8 nozzle, Creality Ender-3 Pro 0.2 nozzle, Creality Ender-3 Pro 0.4 nozzle, Creality Ender-3 Pro 0.6 nozzle, Creality Ender-3 Pro 0.8 nozzle, Creality Ender-3 V2 0.4 nozzle, Creality Ender-3 V2 Neo 0.4 nozzle, Creality Ender-3 S1 0.4 nozzle, Creality Ender-3 S1 Pro 0.4 nozzle, Creality Ender-3 S1 Plus 0.2 nozzle, Creality Ender-3 S1 Plus 0.4 nozzle, Creality Ender-3 S1 Plus 0.6 nozzle, Creality Ender-3 S1 Plus 0.8 nozzle, Creality Ender-5 0.4 nozzle, Creality Ender-5 Plus 0.4 nozzle, Creality Ender-5 Pro (2019) 0.2 nozzle, Creality Ender-5 Pro (2019) 0.25 nozzle, Creality Ender-5 Pro (2019) 0.3 nozzle, Creality Ender-5 Pro (2019) 0.4 nozzle, Creality Ender-5 Pro (2019) 0.5 nozzle, Creality Ender-5 Pro (2019) 0.6 nozzle, Creality Ender-5 Pro (2019) 0.8 nozzle, Creality Ender-5 Pro (2019) 1.0 nozzle, Creality Ender-5S 0.4 nozzle, Creality Ender-5 S1 0.4 nozzle, Creality Ender-6 0.4 nozzle, Creality K1 (0.4 nozzle), Creality K1 (0.6 nozzle), Creality K1 (0.8 nozzle), Creality K1 Max (0.4 nozzle), Creality K1 Max (0.6 nozzle), Creality K1 Max (0.8 nozzle), Creality CR-10 SE 0.2 nozzle, Creality CR-10 SE 0.4 nozzle, Creality CR-10 SE 0.6 nozzle, Creality CR-10 SE 0.8 nozzle, Creality CR-M4 0.4 nozzle (inherited)
filament id: GFL99 inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was true (inherited)
nozzle temperature range high: 230 inherited
nozzle temperature range low: 190 inherited
overhang fan speed: 100 inherited
overhang fan threshold: 50% inherited
reduce fan stop start freq: 1 overridden
was 1 (inherited)
setting id: GFSL99_00 overridden
was GFSA04 (inherited)
slow down for layer cooling: 1 inherited
temperature vitrification: 60 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_cost": [
    "30"
  ],
  "filament_type": [
    "PLA"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "50"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "50"
  ],
  "cool_plate_temp": [
    "50"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "220"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "0.95"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "textured_plate_temp": [
    "50"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n{if (position[2] > first_layer_height) }\nM104 S[nozzle_temperature]\n{else}\nM104 S[first_layer_temperature]\n{endif}\n\n{if(initial_extruder != current_extruder || position[2] > first_layer_height)}\n{if (position[2] +0.4  < printable_height) }\nG2 Z{position[2]  + 0.4} I0.86 J0.86 P1 F10000 ; spiral lift a little from second lift\nG1 X205 Y345 F20000\nG1 Z{position[2] } F1200\n{else}\nG1 X205 Y345 F20000\n{endif}\n{endif}\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "4"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "50%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "60"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "50"
  ],
  "cool_plate_temp_initial_layer": [
    "50"
  ],
  "filament_max_volumetric_speed": [
    "18"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "220"
  ],
  "textured_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "190"
  ],
  "nozzle_temperature_range_high": [
    "230"
  ],
  "setting_id": "GFSL99_00",
  "filament_id": "GFL99",
  "compatible_printers": [
    "Creality K2 Plus 0.2 nozzle",
    "Creality K2 Plus 0.4 nozzle",
    "Creality K2 Plus 0.6 nozzle",
    "Creality K2 Plus 0.8 nozzle"
  ],
  "name": "Creality Generic PLA @K2-all"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:53