Creality Generic TPU

Generic · TPU · by anycubic-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_tpu

→

Creality Generic TPU

Compatible printers (15)

Creality CR-10 SE 0.2 nozzle
Creality CR-10 SE 0.4 nozzle
Creality CR-10 SE 0.6 nozzle
Creality CR-10 SE 0.8 nozzle
Creality CR-10 V3 0.4 nozzle
Creality CR-10 V3 0.6 nozzle
Creality Ender-3 S1 0.4 nozzle
Creality Ender-3 S1 Pro 0.4 nozzle
Creality K1 0.4 nozzle
Creality K1 0.6 nozzle
Creality K1 0.8 nozzle
Creality K1 Max 0.4 nozzle
Creality K1 Max 0.6 nozzle
Creality K1 Max 0.8 nozzle
Creality Sermoon V1 0.4 nozzle

Inherited from this (4)

Settings

Basic information

Material variant: TPU inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.24 inherited
Cost (/kg): 35 inherited

Print temperature

Nozzle (initial layer) (°C): 235 inherited
Nozzle (other layers) (°C): 235 inherited

Cooling

Fan minimum (%): 100 inherited
Fan maximum (%): 100 inherited
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 100 inherited
Slow down if layer below (sec): 5 inherited
Min speed when slowed (mm/s): 5 inherited

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 3.2 overridden
was 15 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	40 inherited	40 inherited
Engineering Plate	40 inherited	40 inherited
High Temp Plate	40 inherited	40 inherited
Textured PEI Plate	50 inherited	40 inherited

Other settings

additional cooling fan speed: 0 inherited
bed type: Cool Plate inherited
compatible printers: Creality CR-10 V3 0.4 nozzle, Creality CR-10 V3 0.6 nozzle, Creality K1 (0.4 nozzle), Creality K1 (0.6 nozzle), Creality K1 (0.8 nozzle), Creality K1 Max (0.4 nozzle), Creality K1 Max (0.6 nozzle), Creality K1 Max (0.8 nozzle), Creality Sermoon V1 0.4 nozzle, Creality CR-10 SE 0.2 nozzle, Creality CR-10 SE 0.4 nozzle, Creality CR-10 SE 0.6 nozzle, Creality CR-10 SE 0.8 nozzle, Creality Ender-3 S1 Pro 0.4 nozzle, Creality Ender-3 S1 0.4 nozzle overridden
filament id: GFU99 overridden
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 250 inherited
nozzle temperature range low: 210 inherited
overhang fan speed: 100 inherited
overhang fan threshold: 50% inherited
reduce fan stop start freq: 1 inherited
setting id: GFSA04 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 50 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_cost": [
    "35"
  ],
  "filament_type": [
    "TPU"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "40"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "40"
  ],
  "cool_plate_temp": [
    "40"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "235"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "5"
  ],
  "textured_plate_temp": [
    "40"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "5"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "50%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "50"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "40"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "40"
  ],
  "cool_plate_temp_initial_layer": [
    "40"
  ],
  "filament_max_volumetric_speed": [
    "3.2"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "235"
  ],
  "textured_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "210"
  ],
  "nozzle_temperature_range_high": [
    "250"
  ],
  "setting_id": "GFSA04",
  "filament_id": "GFU99",
  "compatible_printers": [
    "Creality CR-10 V3 0.4 nozzle",
    "Creality CR-10 V3 0.6 nozzle",
    "Creality K1 (0.4 nozzle)",
    "Creality K1 (0.6 nozzle)",
    "Creality K1 (0.8 nozzle)",
    "Creality K1 Max (0.4 nozzle)",
    "Creality K1 Max (0.6 nozzle)",
    "Creality K1 Max (0.8 nozzle)",
    "Creality Sermoon V1 0.4 nozzle",
    "Creality CR-10 SE 0.2 nozzle",
    "Creality CR-10 SE 0.4 nozzle",
    "Creality CR-10 SE 0.6 nozzle",
    "Creality CR-10 SE 0.8 nozzle",
    "Creality Ender-3 S1 Pro 0.4 nozzle",
    "Creality Ender-3 S1 0.4 nozzle"
  ],
  "name": "Creality Generic TPU"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:52