Overture ABS @Qidi Q2 0.8 nozzle

Overture · ABS · 0.80mm nozzle · by anycubic-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_q_common

→

Overture ABS@Q2-Series

→

Overture ABS @Qidi Q2 0.8 nozzle

Compatible printers (1)

Qidi Q2 0.8 nozzle

Settings

Basic information

Material variant: ABS inherited
Vendor: Overture inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.12 inherited
Cost (/kg): 0 inherited

Print temperature

Nozzle (initial layer) (°C): 250 inherited
Nozzle (other layers) (°C): 255 inherited
Chamber (°C): 60 inherited

Cooling

Fan minimum (%): 20 inherited
Fan maximum (%): 80 inherited
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 60 inherited
Slow down if layer below (sec): 6 inherited
Min speed when slowed (mm/s): 10 overridden
was 20 (inherited)

Flow

Flow ratio: 0.96 inherited
Max volumetric speed (mm³/s): 17 inherited

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	60 inherited	60 inherited
Engineering Plate	60 inherited	60 inherited
High Temp Plate	90 inherited	90 inherited

Other settings

activate air filtration: 1 inherited
additional cooling fan speed: 0 inherited
additional cooling fan speed unseal: 0 inherited
bed type: Cool Plate inherited
box temperature: 0 inherited
box temperature range high: 45 inherited
box temperature range low: 0 inherited
compatible printers: Qidi Q2 0.8 nozzle overridden
was — (inherited)
complete print exhaust fan speed: 0 inherited
dont slow down outer wall: 0 inherited
during print exhaust fan speed: 0 inherited
enable pressure advance: 1 inherited
filament adhesiveness category: 200 inherited
filament flush temp: 0 inherited
filament flush volumetric speed: 0 inherited
filament id: GFB99 inherited
filament long retractions when ec: nil inherited
filament minimal purge on wipe tower: 15 inherited
filament pre cooling temperature: 0 inherited
filament ramming travel time: 0 inherited
filament ramming volumetric speed: -1 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction distances when ec: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 280 inherited
nozzle temperature range low: 240 inherited
overhang fan speed: 80 inherited
overhang fan threshold: 25% inherited
pressure advance: 0.01 overridden
was 0.033 (inherited)
reduce fan stop start freq: 1 inherited
setting id: GFSA04 overridden
was GFSA04 (inherited)
slow down for layer cooling: 1 inherited
temperature vitrification: 100 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "80"
  ],
  "fan_min_speed": [
    "20"
  ],
  "filament_cost": [
    "0"
  ],
  "filament_type": [
    "ABS"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "60"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "90"
  ],
  "box_temperature": [
    "0"
  ],
  "cool_plate_temp": [
    "60"
  ],
  "filament_vendor": [
    "Overture"
  ],
  "filament_density": [
    "1.12"
  ],
  "filament_soluble": [
    "0"
  ],
  "pressure_advance": [
    "0.01"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; Filament-specific end gcode \n;END gcode for filament"
  ],
  "nozzle_temperature": [
    "255"
  ],
  "overhang_fan_speed": [
    "80"
  ],
  "chamber_temperature": [
    "60"
  ],
  "filament_flow_ratio": [
    "0.96"
  ],
  "filament_flush_temp": [
    "0"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; Filament start gcode"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "6"
  ],
  "fan_cooling_layer_time": [
    "60"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "activate_air_filtration": [
    "1"
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "box_temperature_range_low": [
    "0"
  ],
  "dont_slow_down_outer_wall": [
    "0"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "100"
  ],
  "box_temperature_range_high": [
    "45"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "60"
  ],
  "filament_ramming_travel_time": [
    "0"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "90"
  ],
  "cool_plate_temp_initial_layer": [
    "60"
  ],
  "filament_max_volumetric_speed": [
    "17"
  ],
  "during_print_exhaust_fan_speed": [
    "0"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "filament_flush_volumetric_speed": [
    "0"
  ],
  "complete_print_exhaust_fan_speed": [
    "0"
  ],
  "filament_pre_cooling_temperature": [
    "0"
  ],
  "nozzle_temperature_initial_layer": [
    "250"
  ],
  "filament_long_retractions_when_ec": [
    "nil"
  ],
  "filament_ramming_volumetric_speed": [
    "-1"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "additional_cooling_fan_speed_unseal": [
    "0"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "filament_retraction_distances_when_ec": [
    "nil"
  ],
  "setting_id": "GFSA04",
  "filament_id": "GFB99",
  "compatible_printers": [
    "Qidi Q2 0.8 nozzle"
  ],
  "nozzle_temperature_range_low": [
    "240"
  ],
  "nozzle_temperature_range_high": [
    "280"
  ],
  "filament_adhesiveness_category": [
    "200"
  ],
  "name": "Overture ABS @Qidi Q2 0.8 nozzle"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:52