Generic PLA High Speed @BBL X1C 0.2 nozzle

Generic · PLA · 0.20mm nozzle · by elegoo-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Strip G-code from download

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pla

→

Generic PLA High Speed @base

→

Generic PLA High Speed @BBL X1C

→

Generic PLA High Speed @BBL X1C 0.2 nozzle

Compatible printers (4)

Bambu Lab P1S 0.2 nozzle
Bambu Lab X1 0.2 nozzle
Bambu Lab X1 Carbon 0.2 nozzle
Bambu Lab X1E 0.2 nozzle

Settings

Basic information

Material variant: PLA inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.24 inherited
Cost (/kg): 30 inherited

Print temperature

Nozzle (initial layer) (°C): 220 inherited
Nozzle (other layers) (°C): 220 inherited

Cooling

Fan minimum (%): 100 inherited
Fan maximum (%): 100 inherited
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 100 inherited
Slow down if layer below (sec): 4 inherited
Min speed when slowed (mm/s): 5 inherited

Flow

Flow ratio: 0.98 inherited
Max volumetric speed (mm³/s): 2 overridden
was 18 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	50 inherited	50 inherited
Engineering Plate	50 inherited	50 inherited
High Temp Plate	50 inherited	50 inherited
Textured PEI Plate	50 inherited	50 inherited

Custom G-code

filament_start_gcode inherited

; filament start gcode
{if  (bed_temperature[current_extruder] >55)||(bed_temperature_initial_layer[current_extruder] >55)}M106 P3 S200
{elsif(bed_temperature[current_extruder] >50)||(bed_temperature_initial_layer[current_extruder] >50)}M106 P3 S150
{elsif(bed_temperature[current_extruder] >45)||(bed_temperature_initial_layer[current_extruder] >45)}M106 P3 S50
{endif}

{if activate_air_filtration[current_extruder] && support_air_filtration}
M106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} 
{endif}

Other settings

additional cooling fan speed: 0 inherited
bed type: Cool Plate inherited
compatible printers: Bambu Lab X1 Carbon 0.2 nozzle, Bambu Lab X1 0.2 nozzle, Bambu Lab P1S 0.2 nozzle, Bambu Lab X1E 0.2 nozzle overridden
was Bambu Lab X1 Carbon 0.4 nozzle, Bambu Lab X1 0.4 nozzle, Bambu Lab P1S 0.4 nozzle, Bambu Lab X1E 0.4 nozzle, Bambu Lab X1 Carbon 0.6 nozzle, Bambu Lab X1 Carbon 0.8 nozzle, Bambu Lab X1 0.8 nozzle, Bambu Lab X1 0.6 nozzle, Bambu Lab P1S 0.6 nozzle, Bambu Lab P1S 0.8 nozzle, Bambu Lab X1E 0.6 nozzle, Bambu Lab X1E 0.8 nozzle (inherited)
filament id: GFL95 inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was true (inherited)
nozzle temperature range high: 230 inherited
nozzle temperature range low: 190 inherited
overhang fan speed: 100 inherited
overhang fan threshold: 50% inherited
reduce fan stop start freq: 1 inherited
setting id: GFSL95_01 overridden
was GFSL95_00 (inherited)
slow down for layer cooling: 1 inherited
temperature vitrification: 60 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_cost": [
    "30"
  ],
  "filament_type": [
    "PLA"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "50"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "50"
  ],
  "cool_plate_temp": [
    "50"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "220"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "0.98"
  ],
  "slow_down_min_speed": [
    "5"
  ],
  "textured_plate_temp": [
    "50"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n{if  (bed_temperature[current_extruder] >55)||(bed_temperature_initial_layer[current_extruder] >55)}M106 P3 S200\n{elsif(bed_temperature[current_extruder] >50)||(bed_temperature_initial_layer[current_extruder] >50)}M106 P3 S150\n{elsif(bed_temperature[current_extruder] >45)||(bed_temperature_initial_layer[current_extruder] >45)}M106 P3 S50\n{endif}\n\n{if activate_air_filtration[current_extruder] && support_air_filtration}\nM106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} \n{endif}"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "4"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "50%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "60"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "50"
  ],
  "cool_plate_temp_initial_layer": [
    "50"
  ],
  "filament_max_volumetric_speed": [
    "2"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "220"
  ],
  "textured_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "190"
  ],
  "nozzle_temperature_range_high": [
    "230"
  ],
  "filament_id": "GFL95",
  "setting_id": "GFSL95_01",
  "compatible_printers": [
    "Bambu Lab X1 Carbon 0.2 nozzle",
    "Bambu Lab X1 0.2 nozzle",
    "Bambu Lab P1S 0.2 nozzle",
    "Bambu Lab X1E 0.2 nozzle"
  ],
  "name": "Generic PLA High Speed @BBL X1C 0.2 nozzle"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:47