Artillery PETG

Artillery · PETG · by elegoo-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pla

→

Artillery Generic PLA

→

Artillery PETG

Compatible printers (4)

Artillery Sidewinder X3 Plus 0.4 nozzle
Artillery Sidewinder X3 Pro 0.4 nozzle
Artillery Sidewinder X4 Plus 0.4 nozzle
Artillery Sidewinder X4 Pro 0.4 nozzle

Settings

Basic information

Material variant: PETG overridden
was PLA (inherited)
Vendor: Artillery overridden
was Generic (inherited)
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.24 inherited
Cost (/kg): 30 inherited

Print temperature

Nozzle (initial layer) (°C): 250 overridden
was 200 (inherited)
Nozzle (other layers) (°C): 250 overridden
was 200 (inherited)

Cooling

Fan minimum (%): 10 overridden
was 100 (inherited)
Fan maximum (%): 40 overridden
was 100 (inherited)
Disable fan for first N layers: 3 overridden
was 1 (inherited)
Full fan if layer below (sec): 30 overridden
was 100 (inherited)
Slow down if layer below (sec): 12 overridden
was 8 (inherited)
Min speed when slowed (mm/s): 5 inherited

Flow

Flow ratio: 0.98 inherited
Max volumetric speed (mm³/s): 9 overridden
was 12 (inherited)

Retraction

Retraction length (mm): 1.3 overridden
was nil (inherited)
Retraction speed (mm/s): 40 overridden
was nil (inherited)
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	50 inherited	50 inherited
Engineering Plate	50 inherited	50 inherited
High Temp Plate	70 overridden was 60	70 overridden was 60
Textured PEI Plate	50 inherited	50 inherited

Other settings

additional cooling fan speed: 0 inherited
bed type: Cool Plate inherited
compatible printers: Artillery Sidewinder X3 Pro 0.4 nozzle, Artillery Sidewinder X3 Plus 0.4 nozzle, Artillery Sidewinder X4 Pro 0.4 nozzle, Artillery Sidewinder X4 Plus 0.4 nozzle overridden
was Artillery Sidewinder X1 0.4 nozzle, Artillery Genius 0.4 nozzle, Artillery Sidewinder X2 0.4 nozzle, Artillery Genius Pro 0.4 nozzle, Artillery Hornet 0.4 nozzle (inherited)
enable pressure advance: 1 overridden
filament id: GFL99 inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: 0.4 overridden
was nil (inherited)
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was true (inherited)
nozzle temperature range high: 270 overridden
was 230 (inherited)
nozzle temperature range low: 230 overridden
was 190 (inherited)
overhang fan speed: 90 overridden
was 100 (inherited)
overhang fan threshold: 10% overridden
was 50% (inherited)
pressure advance: 0.05 overridden
reduce fan stop start freq: 1 inherited
setting id: GFSA04 inherited
slow down for layer cooling: 1 inherited
temperature vitrification: 220 overridden
was 60 (inherited)

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "40"
  ],
  "fan_min_speed": [
    "10"
  ],
  "filament_cost": [
    "30"
  ],
  "filament_type": [
    "PETG"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "50"
  ],
  "filament_z_hop": [
    "0.4"
  ],
  "hot_plate_temp": [
    "70"
  ],
  "cool_plate_temp": [
    "50"
  ],
  "filament_vendor": [
    "Artillery"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "250"
  ],
  "overhang_fan_speed": [
    "90"
  ],
  "filament_flow_ratio": [
    "0.98"
  ],
  "slow_down_min_speed": [
    "5"
  ],
  "textured_plate_temp": [
    "50"
  ],
  "filament_settings_id": [
    "Artillery PETG"
  ],
  "filament_start_gcode": [
    ""
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "12"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "10%"
  ],
  "filament_retraction_speed": [
    "40"
  ],
  "temperature_vitrification": [
    "220"
  ],
  "filament_retraction_length": [
    "1.3"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "70"
  ],
  "cool_plate_temp_initial_layer": [
    "50"
  ],
  "filament_max_volumetric_speed": [
    "9"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "250"
  ],
  "textured_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "230"
  ],
  "nozzle_temperature_range_high": [
    "270"
  ],
  "setting_id": "GFSA04",
  "filament_id": "GFL99",
  "compatible_printers": [
    "Artillery Sidewinder X3 Pro 0.4 nozzle",
    "Artillery Sidewinder X3 Plus 0.4 nozzle",
    "Artillery Sidewinder X4 Pro 0.4 nozzle",
    "Artillery Sidewinder X4 Plus 0.4 nozzle"
  ],
  "pressure_advance": [
    "0.05"
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "name": "Artillery PETG"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:46