slicershare (test)
← Prusament PC-CF @CORE One 0.8

History of Prusament PC-CF @CORE One 0.8

Direct edits to this profile, and edits to any profile it inherits from. An inherited change can shift this profile's effective behavior even when this profile itself wasn't touched.

Inherits from: fdm_filament_common → fdm_filament_pc → Prusament PC-CF @CORE One
  1. direct edit v1 — created
    2026-05-19 12:46
    Profile created at this point. No prior version to diff against.
  2. via parent v22 of fdm_filament_pc — updated
    2026-05-19 12:31
    Settings (11)
    • eng plate temp 110 → 100
    • eng plate temp initial layer 110 → 100
    • fan max speed 60 → 50
    • filament max volumetric speed 23.2 → 10
    • filament z hop types added nil
    • hot plate temp 110 → 100
    • hot plate temp initial layer 110 → 100
    • nozzle temperature 280 → 270
    • nozzle temperature range low 260 → 250
    • textured plate temp 110 → 100
    • textured plate temp initial layer 110 → 100
  3. via parent v33 of fdm_filament_common — updated
    2026-05-19 12:31
    Settings (3)
    • filament z hop types added nil
    • textured plate temp added 60
    • textured plate temp initial layer added 60
  4. via parent v21 of fdm_filament_pc — updated
    2026-05-19 12:31
    Settings (2)
    • nozzle temperature range high 290 → 280
    • temperature vitrification 120 → 140
  5. via parent v32 of fdm_filament_common — updated
    2026-05-19 12:31
    Settings (7)
    • bed type added Cool Plate
    • filament end gcode ; filament end gcode M106 P3 S0 → ; filament end gcode
    • filament is support removed 0
    • filament z hop types removed nil
    • required nozzle HRC removed 3
    • textured plate temp removed 60
    • textured plate temp initial layer removed 60
  6. via parent v31 of fdm_filament_common — updated
    2026-05-19 12:30
    Settings (7)
    • bed type removed Cool Plate
    • filament end gcode ; filament end gcode → ; filament end gcode M106 P3 S0
    • filament is support added 0
    • filament z hop types added nil
    • required nozzle HRC added 3
    • textured plate temp added 60
    • textured plate temp initial layer added 60
  7. via parent v20 of fdm_filament_pc — updated
    2026-05-19 12:30
    Settings (8)
    • bed type Textured PEI Plate → Cool Plate
    • filament id removed GFC99
    • filament z hop types removed nil
    • idle temperature removed 0
    • nozzle temperature range high 280 → 290
    • temperature vitrification 140 → 120
    • textured plate temp 60 → 110
    • textured plate temp initial layer 60 → 110
  8. via parent v1 of Prusament PC-CF @CORE One — created
    2026-05-19 12:30
    Profile created at this point. No prior version to diff against.
  9. via parent v30 of fdm_filament_common — updated
    2026-05-19 12:29
    Settings (4)
    • bed type Textured PEI Plate → Cool Plate
    • filament z hop types removed nil
    • textured plate temp removed 60
    • textured plate temp initial layer removed 60
  10. via parent v19 of fdm_filament_pc — updated
    2026-05-19 12:29
    Settings (49)
    • activate air filtration removed 0
    • activate chamber temp control removed 0
    • additional cooling fan speed removed 70
    • bed type added Textured PEI Plate
    • chamber temperature removed 0
    • complete print exhaust fan speed removed 70
    • default filament colour removed —
    • during print exhaust fan speed removed 70
    • enable overhang bridge fan removed 1
    • enable pressure advance removed 1
    • fan max speed 40 → 60
    • filament cooling final speed removed 3.4
    • filament cooling initial speed removed 2.2
    • filament cooling moves removed 4
    • filament cost 37.50 → 20
    • filament diameter 2.8 → 1.75
    • filament end gcode ; filament end gcode M106 P3 S0 → ; filament end gcode
    • filament id added GFC99
    • filament is support removed 0
    • filament load time removed 0
    • filament loading speed removed 28
    • filament loading speed start removed 3
    • filament max volumetric speed 25 → 23.2
    • filament multitool ramming removed 0
    • filament multitool ramming flow removed 10
    • filament multitool ramming volume removed 10
    • filament notes removed —
    • filament ramming parameters removed 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • filament retract lift above removed nil
    • filament retract lift below removed nil
    • filament retract lift enforce removed nil
    • filament shrink removed 100%
    • filament start gcode ; filament start gcode {if (bed_temperature[current_extruder] >45)||(bed_temperature_initial_layer[current_extruder] >45)}M106 P3 S255 {elsif(bed_temperature[current_extruder] >35)||(bed_temperature_initial_layer[current_extruder] >35)}M106 P3 S180 {endif} {if activate_air_filtration[current_extruder] && support_air_filtration} M106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} {endif} → ; Filament gcode
    • filament toolchange delay removed 0
    • filament unload time removed 0
    • filament unloading speed removed 90
    • filament unloading speed start removed 100
    • idle temperature added 0
    • nozzle temperature 270 → 280
    • nozzle temperature range high 240 → 280
    • nozzle temperature range low 190 → 260
    • overhang fan speed 50 → 60
    • overhang fan threshold 50% → 25%
    • pressure advance removed 0.4
    • required nozzle HRC removed 3
    • support material interface fan speed removed -1
    • temperature vitrification 55 → 140
    • textured plate temp 110 → 60
    • textured plate temp initial layer 110 → 60
  11. via parent v29 of fdm_filament_common — updated
    2026-05-19 12:27
    Identity / metadata
    • Vendor: Volumic → Generic
    Settings (35)
    • bed type Hot Plate → Textured PEI Plate
    • close fan the first x layers 1 → 3
    • cool plate temp 50 → 60
    • cool plate temp initial layer 50 → 60
    • eng plate temp 50 → 60
    • eng plate temp initial layer 50 → 60
    • fan min speed 60 → 35
    • filament cost 37.50 → 0
    • filament density 1 → 0
    • filament deretraction speed added nil
    • filament end gcode added ; filament end gcode
    • filament flow ratio added 1
    • filament max volumetric speed 42 → 0
    • filament retract before wipe added nil
    • filament retract restart extra added nil
    • filament retract when changing layer added nil
    • filament retraction length added nil
    • filament retraction minimum travel added nil
    • filament retraction speed added nil
    • filament soluble added 0
    • filament start gcode added ; Filament gcode
    • filament vendor Volumic → Generic
    • filament wipe added nil
    • filament wipe distance added nil
    • filament z hop added nil
    • filament z hop types added nil
    • hot plate temp 50 → 60
    • hot plate temp initial layer 50 → 60
    • nozzle temperature 210 → 200
    • nozzle temperature initial layer 210 → 200
    • overhang fan threshold added 95%
    • reduce fan stop start freq added 0
    • temperature vitrification added 100
    • textured plate temp 50 → 60
    • textured plate temp initial layer 50 → 60
  12. via parent v28 of fdm_filament_common — updated
    2026-05-19 12:27
    Identity / metadata
    • Vendor: Generic → Volumic
    • Material: OTHER → PLA
    Settings (73)
    • activate air filtration removed 0
    • activate chamber temp control removed 0
    • additional cooling fan speed removed 70
    • bed type added Hot Plate
    • chamber temperature removed 0
    • complete print exhaust fan speed removed 70
    • cool plate temp 35 → 50
    • cool plate temp initial layer 35 → 50
    • default filament colour removed —
    • during print exhaust fan speed removed 70
    • enable overhang bridge fan removed 1
    • enable pressure advance removed 1
    • eng plate temp 0 → 50
    • eng plate temp initial layer 0 → 50
    • fan max speed 0 → 100
    • fan min speed 0 → 60
    • filament cooling final speed removed 3.4
    • filament cooling initial speed removed 2.2
    • filament cooling moves removed 4
    • filament cost 5 → 37.50
    • filament density 1.24 → 1
    • filament deretraction speed removed nil
    • filament diameter 2.8 → 1.75
    • filament end gcode removed ; filament end gcode M106 P3 S0
    • filament flow ratio removed 1
    • filament is support removed 0
    • filament load time removed 0
    • filament loading speed removed 28
    • filament loading speed start removed 3
    • filament max volumetric speed 300 → 42
    • filament multitool ramming removed 0
    • filament multitool ramming flow removed 10
    • filament multitool ramming volume removed 10
    • filament notes removed —
    • filament ramming parameters removed 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • filament retract before wipe removed nil
    • filament retract lift above removed nil
    • filament retract lift below removed nil
    • filament retract lift enforce removed nil
    • filament retract restart extra removed nil
    • filament retract when changing layer removed nil
    • filament retraction length removed nil
    • filament retraction minimum travel removed nil
    • filament retraction speed removed nil
    • filament shrink removed 100%
    • filament soluble removed 0
    • filament start gcode removed ; filament start gcode {if (bed_temperature[current_extruder] >45)||(bed_temperature_initial_layer[current_extruder] >45)}M106 P3 S255 {elsif(bed_temperature[current_extruder] >35)||(bed_temperature_initial_layer[current_extruder] >35)}M106 P3 S180 {endif} {if activate_air_filtration[current_extruder] && support_air_filtration} M106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} {endif}
    • filament toolchange delay removed 0
    • filament type added PLA
    • filament unload time removed 0
    • filament unloading speed removed 90
    • filament unloading speed start removed 100
    • filament vendor Generic → Volumic
    • filament wipe removed nil
    • filament wipe distance removed nil
    • filament z hop removed nil
    • filament z hop types removed nil
    • hot plate temp 1 → 50
    • hot plate temp initial layer 60 → 50
    • nozzle temperature 220 → 210
    • nozzle temperature initial layer 220 → 210
    • nozzle temperature range high removed 240
    • nozzle temperature range low removed 190
    • overhang fan threshold removed 50%
    • pressure advance removed 0.4
    • reduce fan stop start freq removed 0
    • required nozzle HRC removed 3
    • slow down layer time 30 → 8
    • slow down min speed 20 → 10
    • support material interface fan speed removed -1
    • temperature vitrification removed 55
    • textured plate temp 55 → 50
    • textured plate temp initial layer 55 → 50
  13. via parent v18 of fdm_filament_pc — updated
    2026-05-19 12:26
    Settings (48)
    • activate chamber temp control added 0
    • additional cooling fan speed added 70
    • chamber temperature added 0
    • chamber temperatures removed 0
    • compatible printers removed —
    • default filament colour added —
    • enable overhang bridge fan added 1
    • enable pressure advance added 1
    • fan max speed 60 → 40
    • filament cooling final speed added 3.4
    • filament cooling initial speed added 2.2
    • filament cooling moves added 4
    • filament cost 20 → 37.50
    • filament diameter 1.75 → 2.8
    • filament end gcode ; filament end gcode → ; filament end gcode M106 P3 S0
    • filament load time added 0
    • filament loading speed added 28
    • filament loading speed start added 3
    • filament long retractions when cut removed nil
    • filament max volumetric speed 23.2 → 25
    • filament multitool ramming added 0
    • filament multitool ramming flow added 10
    • filament multitool ramming volume added 10
    • filament notes added —
    • filament ramming parameters added 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • filament retract lift above added nil
    • filament retract lift below added nil
    • filament retract lift enforce added nil
    • filament retraction distances when cut removed nil
    • filament scarf gap removed 0%
    • filament scarf height removed 10%
    • filament scarf length removed 10
    • filament scarf seam type removed none
    • filament start gcode ; Filament gcode → ; filament start gcode {if (bed_temperature[current_extruder] >45)||(bed_temperature_initial_layer[current_extruder] >45)}M106 P3 S255 {elsif(bed_temperature[current_extruder] >35)||(bed_temperature_initial_layer[current_extruder] >35)}M106 P3 S180 {endif} {if activate_air_filtration[current_extruder] && support_air_filtration} M106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} {endif}
    • filament toolchange delay added 0
    • filament unload time added 0
    • filament unloading speed added 90
    • filament unloading speed start added 100
    • nozzle temperature 280 → 270
    • nozzle temperature range high 280 → 240
    • nozzle temperature range low 260 → 190
    • overhang fan speed 60 → 50
    • overhang fan threshold 25% → 50%
    • pressure advance added 0.4
    • supertack plate temp removed 45
    • supertack plate temp initial layer removed 45
    • support material interface fan speed added -1
    • temperature vitrification 140 → 55
  14. via parent v27 of fdm_filament_common — updated
    2026-05-19 12:26
    Identity / metadata
    • Vendor: Co Print → Generic
    • Material: PLA → OTHER
    Settings (61)
    • activate air filtration added 0
    • activate chamber temp control added 0
    • additional cooling fan speed added 70
    • bed type removed Cool Plate
    • chamber temperature added 0
    • close fan the first x layers 3 → 1
    • complete print exhaust fan speed added 70
    • cool plate temp 60 → 35
    • cool plate temp initial layer 60 → 35
    • default filament colour added —
    • during print exhaust fan speed added 70
    • enable overhang bridge fan added 1
    • enable pressure advance added 1
    • eng plate temp 60 → 0
    • eng plate temp initial layer 60 → 0
    • fan max speed 100 → 0
    • fan min speed 100 → 0
    • filament cooling final speed added 3.4
    • filament cooling initial speed added 2.2
    • filament cooling moves added 4
    • filament cost 0 → 5
    • filament density 0 → 1.24
    • filament diameter 1.75 → 2.8
    • filament end gcode added ; filament end gcode M106 P3 S0
    • filament flow ratio 0.95 → 1
    • filament is support added 0
    • filament load time added 0
    • filament loading speed added 28
    • filament loading speed start added 3
    • filament max volumetric speed 14 → 300
    • filament multitool ramming added 0
    • filament multitool ramming flow added 10
    • filament multitool ramming volume added 10
    • filament notes added —
    • filament ramming parameters added 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • filament retract lift above added nil
    • filament retract lift below added nil
    • filament retract lift enforce added nil
    • filament shrink added 100%
    • filament start gcode added ; filament start gcode {if (bed_temperature[current_extruder] >45)||(bed_temperature_initial_layer[current_extruder] >45)}M106 P3 S255 {elsif(bed_temperature[current_extruder] >35)||(bed_temperature_initial_layer[current_extruder] >35)}M106 P3 S180 {endif} {if activate_air_filtration[current_extruder] && support_air_filtration} M106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} {endif}
    • filament toolchange delay added 0
    • filament type removed PLA
    • filament unload time added 0
    • filament unloading speed added 90
    • filament unloading speed start added 100
    • filament vendor Co Print → Generic
    • filament z hop types added nil
    • hot plate temp 60 → 1
    • nozzle temperature 200 → 220
    • nozzle temperature initial layer 200 → 220
    • nozzle temperature range high added 240
    • nozzle temperature range low added 190
    • overhang fan threshold 95% → 50%
    • pressure advance added 0.4
    • required nozzle HRC added 3
    • slow down layer time 8 → 30
    • slow down min speed 10 → 20
    • support material interface fan speed added -1
    • temperature vitrification 100 → 55
    • textured plate temp 60 → 55
    • textured plate temp initial layer 60 → 55
  15. via parent v26 of fdm_filament_common — updated
    2026-05-19 12:26
    Identity / metadata
    • Vendor: Generic → Co Print
    Settings (6)
    • fan min speed 35 → 100
    • filament end gcode removed ; filament end gcode
    • filament flow ratio 1 → 0.95
    • filament max volumetric speed 0 → 14
    • filament start gcode removed ; Filament gcode
    • filament vendor Generic → Co Print
  16. via parent v25 of fdm_filament_common — updated
    2026-05-19 12:26
    Settings (19)
    • activate air filtration removed 0
    • bed type added Cool Plate
    • chamber temperatures removed 0
    • compatible printers removed —
    • complete print exhaust fan speed removed 70
    • during print exhaust fan speed removed 70
    • filament end gcode ; filament end gcode → ; filament end gcode
    • filament is support removed 0
    • filament long retractions when cut removed nil
    • filament retraction distances when cut removed nil
    • filament scarf gap removed 0%
    • filament scarf height removed 10%
    • filament scarf length removed 10
    • filament scarf seam type removed none
    • filament shrink removed 100%
    • filament z hop types removed nil
    • required nozzle HRC removed 3
    • supertack plate temp removed 45
    • supertack plate temp initial layer removed 45
  17. via parent v17 of fdm_filament_pc — updated
    2026-05-19 12:26
    Settings (23)
    • activate air filtration added 0
    • bed type removed Cool Plate
    • chamber temperatures added 0
    • compatible printers added —
    • complete print exhaust fan speed added 70
    • during print exhaust fan speed added 70
    • filament end gcode ; filament end gcode → ; filament end gcode
    • filament flow ratio 0.94 → 1
    • filament id removed OGFC99
    • filament is support added 0
    • filament long retractions when cut added nil
    • filament max volumetric speed 12 → 23.2
    • filament retraction distances when cut added nil
    • filament scarf gap added 0%
    • filament scarf height added 10%
    • filament scarf length added 10
    • filament scarf seam type added none
    • filament shrink added 100%
    • nozzle temperature range high 290 → 280
    • required nozzle HRC added 3
    • supertack plate temp 0 → 45
    • supertack plate temp initial layer 0 → 45
    • temperature vitrification 120 → 140
  18. via parent v24 of fdm_filament_common — updated
    2026-05-19 12:26
    Settings (19)
    • activate air filtration added 0
    • bed type removed Cool Plate
    • chamber temperatures added 0
    • compatible printers added —
    • complete print exhaust fan speed added 70
    • during print exhaust fan speed added 70
    • filament end gcode ; filament end gcode → ; filament end gcode
    • filament is support added 0
    • filament long retractions when cut added nil
    • filament retraction distances when cut added nil
    • filament scarf gap added 0%
    • filament scarf height added 10%
    • filament scarf length added 10
    • filament scarf seam type added none
    • filament shrink added 100%
    • overhang fan threshold 0% → 95%
    • required nozzle HRC added 3
    • supertack plate temp added 45
    • supertack plate temp initial layer added 45
  19. via parent v16 of fdm_filament_pc — updated
    2026-05-19 12:26
    Identity / metadata
    • Vendor: InfiMech → Generic
    Settings (16)
    • activate air filtration removed 1
    • complete print exhaust fan speed removed 80
    • during print exhaust fan speed removed 100
    • fan max speed 20 → 60
    • filament flow ratio 1 → 0.94
    • filament id added OGFC99
    • filament vendor InfiMech → Generic
    • nozzle temperature 260 → 280
    • nozzle temperature initial layer 260 → 270
    • nozzle temperature range high 280 → 290
    • nozzle temperature range low 240 → 260
    • reduce fan stop start freq 0 → 1
    • slow down min speed 20 → 10
    • supertack plate temp added 0
    • supertack plate temp initial layer added 0
    • temperature vitrification 140 → 120
  20. via parent v23 of fdm_filament_common — updated
    2026-05-19 12:24
    Settings (3)
    • overhang fan threshold 95% → 0%
    • textured plate temp added 60
    • textured plate temp initial layer added 60
  21. via parent v15 of fdm_filament_pc — updated
    2026-05-19 12:24
    Identity / metadata
    • Vendor: Generic → InfiMech
    Settings (13)
    • activate air filtration added 1
    • complete print exhaust fan speed added 80
    • during print exhaust fan speed added 100
    • fan max speed 60 → 20
    • filament max volumetric speed 23.2 → 12
    • filament vendor Generic → InfiMech
    • nozzle temperature 280 → 260
    • nozzle temperature initial layer 270 → 260
    • nozzle temperature range low 260 → 240
    • reduce fan stop start freq 1 → 0
    • slow down min speed 10 → 20
    • textured plate temp added 110
    • textured plate temp initial layer added 110
  22. via parent v14 of fdm_filament_pc — updated
    2026-05-19 12:24
    Identity / metadata
    • Vendor: FlyingBear → Generic
    Settings (12)
    • activate air filtration removed 1
    • complete print exhaust fan speed removed 60
    • fan max speed 20 → 60
    • filament max volumetric speed 12 → 23.2
    • filament vendor FlyingBear → Generic
    • nozzle temperature 260 → 280
    • nozzle temperature initial layer 260 → 270
    • nozzle temperature range low 240 → 260
    • reduce fan stop start freq 0 → 1
    • slow down min speed 20 → 10
    • textured plate temp removed 110
    • textured plate temp initial layer removed 110
  23. via parent v22 of fdm_filament_common — updated
    2026-05-19 12:23
    Settings (3)
    • overhang fan threshold 0% → 95%
    • textured plate temp removed 60
    • textured plate temp initial layer removed 60
  24. via parent v21 of fdm_filament_common — updated
    2026-05-19 12:23
    Settings (1)
    • overhang fan threshold 95% → 0%
  25. via parent v13 of fdm_filament_pc — updated
    2026-05-19 12:23
    Identity / metadata
    • Vendor: Generic → FlyingBear
    Settings (27)
    • activate air filtration 0 → 1
    • bed type added Cool Plate
    • chamber temperatures removed 0
    • complete print exhaust fan speed 70 → 60
    • during print exhaust fan speed removed 70
    • fan max speed 60 → 20
    • filament end gcode added ; filament end gcode
    • filament is support removed 0
    • filament long retractions when cut removed nil
    • filament max volumetric speed 23.2 → 12
    • filament retraction distances when cut removed nil
    • filament scarf gap removed 0%
    • filament scarf height removed 10%
    • filament scarf length removed 10
    • filament scarf seam type removed none
    • filament shrink removed 100%
    • filament start gcode added ; Filament gcode
    • filament vendor Generic → FlyingBear
    • nozzle temperature 280 → 260
    • nozzle temperature initial layer 270 → 260
    • nozzle temperature range high 290 → 280
    • nozzle temperature range low 260 → 240
    • reduce fan stop start freq 1 → 0
    • required nozzle HRC removed 3
    • supertack plate temp removed 45
    • supertack plate temp initial layer removed 45
    • temperature vitrification 120 → 140
  26. via parent v20 of fdm_filament_common — updated
    2026-05-19 12:23
    Settings (18)
    • activate air filtration removed 0
    • bed type added Cool Plate
    • chamber temperatures removed 0
    • complete print exhaust fan speed removed 70
    • during print exhaust fan speed removed 70
    • filament end gcode added ; filament end gcode
    • filament is support removed 0
    • filament long retractions when cut removed nil
    • filament retraction distances when cut removed nil
    • filament scarf gap removed 0%
    • filament scarf height removed 10%
    • filament scarf length removed 10
    • filament scarf seam type removed none
    • filament shrink removed 100%
    • filament start gcode added ; Filament gcode
    • required nozzle HRC removed 3
    • supertack plate temp removed 45
    • supertack plate temp initial layer removed 45
  27. via parent v12 of fdm_filament_pc — updated
    2026-05-19 12:23
    Identity / metadata
    • Vendor: Snapmaker → Generic
    Settings (34)
    • activate air filtration added 0
    • bed type removed Hot Plate
    • chamber temperatures added 0
    • close fan the first x layers 2 → 3
    • complete print exhaust fan speed added 70
    • during print exhaust fan speed added 70
    • enable pressure advance removed 0
    • filament cooling final speed removed 3.4
    • filament cooling initial speed removed 2.2
    • filament cooling moves removed 0
    • filament end gcode removed —
    • filament load time removed 0
    • filament loading speed removed 25
    • filament loading speed start removed 3
    • filament long retractions when cut added nil
    • filament max volumetric speed 18 → 23.2
    • filament minimal purge on wipe tower 0 → 15
    • filament multitool ramming removed 0
    • filament multitool ramming volume removed 0
    • filament retraction distances when cut added nil
    • filament scarf gap added 0%
    • filament scarf height added 10%
    • filament scarf length added 10
    • filament scarf seam type added none
    • filament shrink added 100%
    • filament start gcode removed —
    • filament toolchange delay removed 0
    • filament unload time removed 0
    • filament unloading speed removed 25
    • filament unloading speed start removed 3
    • filament vendor Snapmaker → Generic
    • pressure advance removed 0.04
    • supertack plate temp 0 → 45
    • supertack plate temp initial layer 0 → 45
  28. via parent v19 of fdm_filament_common — updated
    2026-05-19 12:23
    Identity / metadata
    • Vendor: Snapmaker → Generic
    • Material: OTHER → PLA
    Settings (41)
    • activate air filtration added 0
    • bed type removed Hot Plate
    • chamber temperatures added 0
    • close fan the first x layers 2 → 3
    • complete print exhaust fan speed added 70
    • cool plate temp 0 → 60
    • cool plate temp initial layer 0 → 60
    • during print exhaust fan speed added 70
    • enable pressure advance removed 0
    • eng plate temp 0 → 60
    • eng plate temp initial layer 0 → 60
    • filament cooling final speed removed 3.4
    • filament cooling initial speed removed 2.2
    • filament cooling moves removed 0
    • filament end gcode removed —
    • filament load time removed 0
    • filament loading speed removed 25
    • filament loading speed start removed 3
    • filament long retractions when cut added nil
    • filament minimal purge on wipe tower 0 → 15
    • filament multitool ramming removed 0
    • filament multitool ramming volume removed 0
    • filament retraction distances when cut added nil
    • filament scarf gap added 0%
    • filament scarf height added 10%
    • filament scarf length added 10
    • filament scarf seam type added none
    • filament shrink added 100%
    • filament start gcode removed —
    • filament toolchange delay removed 0
    • filament type added PLA
    • filament unload time removed 0
    • filament unloading speed removed 25
    • filament unloading speed start removed 3
    • filament vendor Snapmaker → Generic
    • pressure advance removed 0.04
    • supertack plate temp added 45
    • supertack plate temp initial layer added 45
    • temperature vitrification 140 → 100
    • textured plate temp 0 → 60
    • textured plate temp initial layer 0 → 60
  29. via parent v11 of fdm_filament_pc — updated
    2026-05-19 12:23
    Identity / metadata
    • Vendor: Generic → Snapmaker
    Settings (24)
    • bed type Cool Plate → Hot Plate
    • close fan the first x layers 3 → 2
    • enable pressure advance added 0
    • filament cooling final speed added 3.4
    • filament cooling initial speed added 2.2
    • filament cooling moves added 0
    • filament end gcode ; filament end gcode → —
    • filament is support added 0
    • filament load time added 0
    • filament loading speed added 25
    • filament loading speed start added 3
    • filament minimal purge on wipe tower 15 → 0
    • filament multitool ramming added 0
    • filament multitool ramming volume added 0
    • filament start gcode ; Filament gcode → —
    • filament toolchange delay added 0
    • filament unload time added 0
    • filament unloading speed added 25
    • filament unloading speed start added 3
    • filament vendor Generic → Snapmaker
    • pressure advance added 0.04
    • required nozzle HRC added 3
    • supertack plate temp added 0
    • supertack plate temp initial layer added 0
  30. via parent v18 of fdm_filament_common — updated
    2026-05-19 12:22
    Identity / metadata
    • Vendor: Generic → Snapmaker
    • Material: PLA → OTHER
    Settings (35)
    • activate air filtration removed 0
    • bed type added Hot Plate
    • chamber temperatures removed 0
    • close fan the first x layers 3 → 2
    • compatible printers removed —
    • complete print exhaust fan speed removed 70
    • cool plate temp 60 → 0
    • cool plate temp initial layer 60 → 0
    • during print exhaust fan speed removed 70
    • enable pressure advance added 0
    • eng plate temp 60 → 0
    • eng plate temp initial layer 60 → 0
    • filament cooling final speed added 3.4
    • filament cooling initial speed added 2.2
    • filament cooling moves added 0
    • filament end gcode ; filament end gcode ;M106 P3 S0 → —
    • filament load time added 0
    • filament loading speed added 25
    • filament loading speed start added 3
    • filament long retractions when cut removed nil
    • filament minimal purge on wipe tower 15 → 0
    • filament multitool ramming added 0
    • filament multitool ramming volume added 0
    • filament retraction distances when cut removed nil
    • filament start gcode ; Filament gcode ;{if activate_air_filtration[current_extruder] && support_air_filtration} ;M106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} ;{endif} → —
    • filament toolchange delay added 0
    • filament type removed PLA
    • filament unload time added 0
    • filament unloading speed added 25
    • filament unloading speed start added 3
    • filament vendor Generic → Snapmaker
    • pressure advance added 0.04
    • temperature vitrification 100 → 140
    • textured plate temp 60 → 0
    • textured plate temp initial layer 60 → 0
  31. via parent v17 of fdm_filament_common — updated
    2026-05-19 12:21
    Settings (14)
    • activate air filtration added 0
    • bed type removed Cool Plate
    • chamber temperatures added 0
    • compatible printers added —
    • complete print exhaust fan speed added 70
    • during print exhaust fan speed added 70
    • filament end gcode ; filament end gcode → ; filament end gcode ;M106 P3 S0
    • filament is support added 0
    • filament long retractions when cut added nil
    • filament retraction distances when cut added nil
    • filament start gcode ; Filament gcode → ; Filament gcode ;{if activate_air_filtration[current_extruder] && support_air_filtration} ;M106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} ;{endif}
    • required nozzle HRC added 3
    • textured plate temp added 60
    • textured plate temp initial layer added 60
  32. via parent v10 of fdm_filament_pc — updated
    2026-05-19 12:21
    Settings (48)
    • activate air filtration removed 0
    • activate chamber temp control removed 0
    • additional cooling fan speed removed 70
    • bed type added Cool Plate
    • chamber temperature removed 0
    • compatible printers removed Ginger G1 1.2 nozzle, Ginger G1 3.0 nozzle, Ginger G1 5.0 nozzle, Ginger G1 8.0 nozzle
    • compatible printers condition removed —
    • compatible prints removed —
    • compatible prints condition removed —
    • complete print exhaust fan speed removed 70
    • default filament colour removed —
    • during print exhaust fan speed removed 70
    • enable overhang bridge fan removed 1
    • enable pressure advance removed 0
    • filament cooling final speed removed 3.4
    • filament cooling initial speed removed 2.2
    • filament cooling moves removed 4
    • filament diameter 1.12838 → 1.75
    • filament end gcode ; filament end gcode M106 P3 S0 → ; filament end gcode
    • filament id removed P510eff9
    • filament is support removed 0
    • filament load time removed 0
    • filament loading speed removed 28
    • filament loading speed start removed 3
    • filament max volumetric speed 23.2 → 18
    • filament multitool ramming removed 0
    • filament multitool ramming flow removed 10
    • filament multitool ramming volume removed 10
    • filament notes removed —
    • filament ramming parameters removed 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • filament retract lift above removed nil
    • filament retract lift below removed nil
    • filament retract lift enforce removed nil
    • filament shrink removed 100%
    • filament start gcode ; filament start gcode {if (bed_temperature[current_extruder] >45)||(bed_temperature_initial_layer[current_extruder] >45)}M106 P3 S255 {elsif(bed_temperature[current_extruder] >35)||(bed_temperature_initial_layer[current_extruder] >35)}M106 P3 S180 {endif} {if activate_air_filtration[current_extruder] && support_air_filtration} M106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} {endif} → ; Filament gcode
    • filament toolchange delay removed 0
    • filament unload time removed 0
    • filament unloading speed removed 90
    • filament unloading speed start removed 100
    • nozzle temperature range high 280 → 290
    • pellet flow coefficient removed 1
    • pressure advance removed 0.4
    • required nozzle HRC removed 0
    • slow down min speed 10 → 20
    • support material interface fan speed removed -1
    • temperature vitrification 140 → 120
    • textured plate temp 55 → 110
    • textured plate temp initial layer 55 → 110
  33. via parent v16 of fdm_filament_common — updated
    2026-05-19 12:21
    Identity / metadata
    • Material: OTHER → PLA
    Settings (64)
    • activate air filtration removed 0
    • activate chamber temp control removed 0
    • additional cooling fan speed removed 70
    • bed type added Cool Plate
    • chamber temperature removed 0
    • close fan the first x layers 1 → 3
    • compatible printers removed Ginger G1 1.2 nozzle, Ginger G1 3.0 nozzle, Ginger G1 5.0 nozzle, Ginger G1 8.0 nozzle
    • compatible printers condition removed —
    • compatible prints removed —
    • compatible prints condition removed —
    • complete print exhaust fan speed removed 70
    • cool plate temp 35 → 60
    • cool plate temp initial layer 35 → 60
    • default filament colour removed —
    • during print exhaust fan speed removed 70
    • enable overhang bridge fan removed 1
    • enable pressure advance removed 0
    • eng plate temp 0 → 60
    • eng plate temp initial layer 0 → 60
    • fan max speed 0 → 100
    • fan min speed 0 → 35
    • filament cooling final speed removed 3.4
    • filament cooling initial speed removed 2.2
    • filament cooling moves removed 4
    • filament cost 5 → 0
    • filament density 1.24 → 0
    • filament diameter 1.12838 → 1.75
    • filament end gcode ; filament end gcode M106 P3 S0 → ; filament end gcode
    • filament id removed P510eff9
    • filament is support removed 0
    • filament load time removed 0
    • filament loading speed removed 28
    • filament loading speed start removed 3
    • filament max volumetric speed 300 → 0
    • filament multitool ramming removed 0
    • filament multitool ramming flow removed 10
    • filament multitool ramming volume removed 10
    • filament notes removed —
    • filament ramming parameters removed 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • filament retract lift above removed nil
    • filament retract lift below removed nil
    • filament retract lift enforce removed nil
    • filament shrink removed 100%
    • filament start gcode ; filament start gcode {if (bed_temperature[current_extruder] >45)||(bed_temperature_initial_layer[current_extruder] >45)}M106 P3 S255 {elsif(bed_temperature[current_extruder] >35)||(bed_temperature_initial_layer[current_extruder] >35)}M106 P3 S180 {endif} {if activate_air_filtration[current_extruder] && support_air_filtration} M106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} {endif} → ; Filament gcode
    • filament toolchange delay removed 0
    • filament type added PLA
    • filament unload time removed 0
    • filament unloading speed removed 90
    • filament unloading speed start removed 100
    • hot plate temp 1 → 60
    • nozzle temperature 220 → 200
    • nozzle temperature initial layer 220 → 200
    • nozzle temperature range high removed 240
    • nozzle temperature range low removed 190
    • overhang fan threshold 50% → 95%
    • pellet flow coefficient removed 1
    • pressure advance removed 0.4
    • required nozzle HRC removed 0
    • slow down layer time 30 → 8
    • slow down min speed 20 → 10
    • support material interface fan speed removed -1
    • temperature vitrification 55 → 100
    • textured plate temp removed 55
    • textured plate temp initial layer removed 55
  34. via parent v9 of fdm_filament_pc — updated
    2026-05-19 12:21
    Settings (49)
    • activate chamber temp control added 0
    • additional cooling fan speed added 70
    • bed type removed Cool Plate
    • chamber temperature added 0
    • compatible printers added Ginger G1 1.2 nozzle, Ginger G1 3.0 nozzle, Ginger G1 5.0 nozzle, Ginger G1 8.0 nozzle
    • compatible printers condition added —
    • compatible prints added —
    • compatible prints condition added —
    • complete print exhaust fan speed added 70
    • default filament colour added —
    • during print exhaust fan speed added 70
    • enable overhang bridge fan added 1
    • enable pressure advance added 0
    • filament cooling final speed added 3.4
    • filament cooling initial speed added 2.2
    • filament cooling moves added 4
    • filament diameter 1.75 → 1.12838
    • filament end gcode ; filament end gcode → ; filament end gcode M106 P3 S0
    • filament id added P510eff9
    • filament is support added 0
    • filament load time added 0
    • filament loading speed added 28
    • filament loading speed start added 3
    • filament max volumetric speed 18 → 23.2
    • filament multitool ramming added 0
    • filament multitool ramming flow added 10
    • filament multitool ramming volume added 10
    • filament notes added —
    • filament ramming parameters added 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • filament retract lift above added nil
    • filament retract lift below added nil
    • filament retract lift enforce added nil
    • filament shrink added 100%
    • filament start gcode ; Filament gcode → ; filament start gcode {if (bed_temperature[current_extruder] >45)||(bed_temperature_initial_layer[current_extruder] >45)}M106 P3 S255 {elsif(bed_temperature[current_extruder] >35)||(bed_temperature_initial_layer[current_extruder] >35)}M106 P3 S180 {endif} {if activate_air_filtration[current_extruder] && support_air_filtration} M106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} {endif}
    • filament toolchange delay added 0
    • filament unload time added 0
    • filament unloading speed added 90
    • filament unloading speed start added 100
    • nozzle temperature range high 290 → 280
    • pellet flow coefficient added 1
    • pressure advance added 0.4
    • required nozzle HRC added 0
    • slow down min speed 20 → 10
    • supertack plate temp removed 0
    • supertack plate temp initial layer removed 0
    • support material interface fan speed added -1
    • temperature vitrification 120 → 140
    • textured plate temp 110 → 55
    • textured plate temp initial layer 110 → 55
  35. via parent v15 of fdm_filament_common — updated
    2026-05-19 12:21
    Identity / metadata
    • Material: PLA → OTHER
    Settings (64)
    • activate air filtration added 0
    • activate chamber temp control added 0
    • additional cooling fan speed added 70
    • chamber temperature added 0
    • close fan the first x layers 3 → 1
    • compatible printers added Ginger G1 1.2 nozzle, Ginger G1 3.0 nozzle, Ginger G1 5.0 nozzle, Ginger G1 8.0 nozzle
    • compatible printers condition added —
    • compatible prints added —
    • compatible prints condition added —
    • complete print exhaust fan speed added 70
    • cool plate temp 60 → 35
    • cool plate temp initial layer 60 → 35
    • default filament colour added —
    • during print exhaust fan speed added 70
    • enable overhang bridge fan added 1
    • enable pressure advance added 0
    • eng plate temp 60 → 0
    • eng plate temp initial layer 60 → 0
    • fan max speed 100 → 0
    • fan min speed 35 → 0
    • filament cooling final speed added 3.4
    • filament cooling initial speed added 2.2
    • filament cooling moves added 4
    • filament cost 0 → 5
    • filament density 0 → 1.24
    • filament diameter 1.75 → 1.12838
    • filament end gcode ; filament end gcode → ; filament end gcode M106 P3 S0
    • filament id added P510eff9
    • filament is support added 0
    • filament load time added 0
    • filament loading speed added 28
    • filament loading speed start added 3
    • filament max volumetric speed 0 → 300
    • filament multitool ramming added 0
    • filament multitool ramming flow added 10
    • filament multitool ramming volume added 10
    • filament notes added —
    • filament ramming parameters added 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6
    • filament retract lift above added nil
    • filament retract lift below added nil
    • filament retract lift enforce added nil
    • filament shrink added 100%
    • filament start gcode ; Filament gcode → ; filament start gcode {if (bed_temperature[current_extruder] >45)||(bed_temperature_initial_layer[current_extruder] >45)}M106 P3 S255 {elsif(bed_temperature[current_extruder] >35)||(bed_temperature_initial_layer[current_extruder] >35)}M106 P3 S180 {endif} {if activate_air_filtration[current_extruder] && support_air_filtration} M106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} {endif}
    • filament toolchange delay added 0
    • filament type removed PLA
    • filament unload time added 0
    • filament unloading speed added 90
    • filament unloading speed start added 100
    • filament z hop types added nil
    • hot plate temp 60 → 1
    • nozzle temperature 200 → 220
    • nozzle temperature initial layer 200 → 220
    • nozzle temperature range high added 240
    • nozzle temperature range low added 190
    • overhang fan threshold 95% → 50%
    • pellet flow coefficient added 1
    • pressure advance added 0.4
    • required nozzle HRC added 0
    • slow down layer time 5 → 30
    • slow down min speed 10 → 20
    • support material interface fan speed added -1
    • temperature vitrification 100 → 55
    • textured plate temp added 55
    • textured plate temp initial layer added 55
  36. via parent v14 of fdm_filament_common — updated
    2026-05-19 12:20
    Settings (15)
    • activate air filtration removed 0
    • chamber temperatures removed 0
    • compatible printers removed —
    • complete print exhaust fan speed removed 70
    • during print exhaust fan speed removed 70
    • filament end gcode ; filament end gcode ;M106 P3 S0 → ; filament end gcode
    • filament is support removed 0
    • filament long retractions when cut removed nil
    • filament retraction distances when cut removed nil
    • filament start gcode ; Filament gcode ;{if activate_air_filtration[current_extruder] && support_air_filtration} ;M106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} ;{endif} → ; Filament gcode
    • filament z hop types removed nil
    • required nozzle HRC removed 3
    • slow down layer time 8 → 5
    • textured plate temp removed 60
    • textured plate temp initial layer removed 60
  37. via parent v13 of fdm_filament_common — updated
    2026-05-19 12:20
    Settings (9)
    • filament end gcode ; filament end gcode M106 P3 S0 → ; filament end gcode ;M106 P3 S0
    • filament scarf gap removed 0%
    • filament scarf height removed 10%
    • filament scarf length removed 10
    • filament scarf seam type removed none
    • filament shrink removed 100%
    • filament start gcode ; Filament gcode {if activate_air_filtration[current_extruder] && support_air_filtration} M106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} {endif} → ; Filament gcode ;{if activate_air_filtration[current_extruder] && support_air_filtration} ;M106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} ;{endif}
    • supertack plate temp removed 45
    • supertack plate temp initial layer removed 45
  38. via parent v12 of fdm_filament_common — updated
    2026-05-19 12:17
    Settings (18)
    • bed type removed Cool Plate
    • chamber temperatures added 0
    • compatible printers added —
    • complete print exhaust fan speed added 70
    • during print exhaust fan speed added 70
    • filament end gcode ; filament end gcode → ; filament end gcode M106 P3 S0
    • filament is support added 0
    • filament long retractions when cut added nil
    • filament retraction distances when cut added nil
    • filament scarf gap added 0%
    • filament scarf height added 10%
    • filament scarf length added 10
    • filament scarf seam type added none
    • filament shrink added 100%
    • filament start gcode ; Filament gcode → ; Filament gcode {if activate_air_filtration[current_extruder] && support_air_filtration} M106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} {endif}
    • required nozzle HRC added 3
    • supertack plate temp added 45
    • supertack plate temp initial layer added 45
  39. via parent v8 of fdm_filament_pc — updated
    2026-05-19 12:16
    Settings (5)
    • activate air filtration added 0
    • filament cost 0 → 20
    • filament max volumetric speed 12 → 18
    • supertack plate temp added 0
    • supertack plate temp initial layer added 0
  40. via parent v11 of fdm_filament_common — updated
    2026-05-19 12:16
    Settings (10)
    • bed type added Cool Plate
    • chamber temperatures removed 0
    • compatible printers removed —
    • complete print exhaust fan speed removed 70
    • during print exhaust fan speed removed 70
    • filament flow ratio 0.98 → 1
    • filament is support removed 0
    • filament max volumetric speed 1 → 0
    • filament start gcode ; Filament start gcode → ; Filament gcode
    • required nozzle HRC removed 3
  41. via parent v10 of fdm_filament_common — updated
    2026-05-19 12:15
    Settings (19)
    • activate air filtration added 0
    • bed type removed Cool Plate
    • chamber temperatures added 0
    • compatible printers added —
    • complete print exhaust fan speed added 70
    • cool plate temp added 60
    • cool plate temp initial layer added 60
    • during print exhaust fan speed added 70
    • eng plate temp added 60
    • eng plate temp initial layer added 60
    • filament flow ratio 1 → 0.98
    • filament is support added 0
    • filament max volumetric speed 0 → 1
    • filament start gcode ; Filament gcode → ; Filament start gcode
    • hot plate temp added 60
    • hot plate temp initial layer added 60
    • required nozzle HRC added 3
    • textured plate temp added 60
    • textured plate temp initial layer added 60
  42. via parent v7 of fdm_filament_pc — updated
    2026-05-19 12:15
    Identity / metadata
    • Vendor: QIDI → Generic
    Settings (12)
    • activate air filtration removed 1
    • activate chamber temp control removed 0
    • compatible printers removed —
    • complete print exhaust fan speed removed 0
    • dont slow down outer wall removed 0
    • during print exhaust fan speed removed 100
    • enable pressure advance removed 1
    • filament cost 20 → 0
    • filament end gcode added ; filament end gcode
    • filament max volumetric speed 23.2 → 12
    • filament start gcode added ; Filament gcode
    • filament vendor QIDI → Generic
  43. via parent v9 of fdm_filament_common — updated
    2026-05-19 12:15
    Settings (31)
    • close fan the first x layers 1 → 3
    • cool plate temp removed 0
    • cool plate temp initial layer removed 0
    • eng plate temp removed 0
    • eng plate temp initial layer removed 0
    • fan cooling layer time 100 → 60
    • fan min speed 100 → 35
    • filament cost 38 → 0
    • filament density 1.25 → 0
    • filament deretraction speed 150 → nil
    • filament flow ratio 1.0 → 1
    • filament max volumetric speed 15 → 0
    • filament retract before wipe 1 → nil
    • filament retract restart extra 0.0 → nil
    • filament retract when changing layer 0 → nil
    • filament retraction length 8.0 → nil
    • filament retraction minimum travel 3.0 → nil
    • filament retraction speed 150 → nil
    • filament start gcode ; filament start gcode → ; Filament gcode
    • filament wipe 1 → nil
    • filament wipe distance 8.0 → nil
    • filament z hop 0.8 → nil
    • hot plate temp removed 0
    • hot plate temp initial layer removed 0
    • nozzle temperature added 200
    • nozzle temperature initial layer added 200
    • overhang fan threshold 50% → 95%
    • reduce fan stop start freq 1 → 0
    • temperature vitrification 60 → 100
    • textured plate temp removed 0
    • textured plate temp initial layer removed 0
  44. via parent v8 of fdm_filament_common — updated
    2026-05-19 12:15
    Settings (31)
    • close fan the first x layers 3 → 1
    • cool plate temp 62 → 0
    • cool plate temp initial layer 66 → 0
    • eng plate temp 62 → 0
    • eng plate temp initial layer 66 → 0
    • fan cooling layer time 60 → 100
    • fan min speed 35 → 100
    • filament cost 0 → 38
    • filament density 0 → 1.25
    • filament deretraction speed nil → 150
    • filament flow ratio 1 → 1.0
    • filament max volumetric speed 0 → 15
    • filament retract before wipe nil → 1
    • filament retract restart extra nil → 0.0
    • filament retract when changing layer nil → 0
    • filament retraction length nil → 8.0
    • filament retraction minimum travel nil → 3.0
    • filament retraction speed nil → 150
    • filament start gcode ; Filament gcode → ; filament start gcode
    • filament wipe nil → 1
    • filament wipe distance nil → 8.0
    • filament z hop nil → 0.8
    • hot plate temp 62 → 0
    • hot plate temp initial layer 66 → 0
    • nozzle temperature removed 200
    • nozzle temperature initial layer removed 200
    • overhang fan threshold 95% → 50%
    • reduce fan stop start freq 0 → 1
    • temperature vitrification 100 → 60
    • textured plate temp 62 → 0
    • textured plate temp initial layer 66 → 0
  45. via parent v7 of fdm_filament_common — updated
    2026-05-19 12:15
    Settings (8)
    • cool plate temp 60 → 62
    • cool plate temp initial layer 60 → 66
    • eng plate temp 60 → 62
    • eng plate temp initial layer 60 → 66
    • hot plate temp 60 → 62
    • hot plate temp initial layer 60 → 66
    • textured plate temp 60 → 62
    • textured plate temp initial layer 60 → 66
  46. via parent v6 of fdm_filament_common — updated
    2026-05-19 12:15
    Identity / metadata
    • Vendor: QIDI → Generic
    Settings (11)
    • activate air filtration removed 1
    • activate chamber temp control removed 0
    • compatible printers removed —
    • complete print exhaust fan speed removed 0
    • dont slow down outer wall removed 0
    • during print exhaust fan speed removed 100
    • enable pressure advance removed 1
    • filament end gcode added ; filament end gcode
    • filament start gcode added ; Filament gcode
    • filament vendor QIDI → Generic
    • reduce fan stop start freq 1 → 0
  47. via parent v6 of fdm_filament_pc — updated
    2026-05-19 12:15
    Identity / metadata
    • Vendor: Generic → QIDI
    Settings (20)
    • activate air filtration added 1
    • activate chamber temp control added 0
    • compatible printers added —
    • complete print exhaust fan speed added 0
    • dont slow down outer wall added 0
    • during print exhaust fan speed added 100
    • enable pressure advance added 1
    • eng plate temp 100 → 110
    • eng plate temp initial layer 100 → 110
    • filament end gcode removed ; filament end gcode
    • filament start gcode removed ; Filament gcode
    • filament vendor Generic → QIDI
    • hot plate temp 100 → 110
    • hot plate temp initial layer 100 → 110
    • nozzle temperature 250 → 280
    • nozzle temperature initial layer 250 → 270
    • overhang fan speed 80 → 60
    • slow down min speed 10 → 20
    • textured plate temp 100 → 110
    • textured plate temp initial layer 100 → 110
  48. via parent v5 of fdm_filament_common — updated
    2026-05-19 12:13
    Identity / metadata
    • Vendor: Generic → QIDI
    Settings (13)
    • activate air filtration added 1
    • activate chamber temp control added 0
    • compatible printers added —
    • complete print exhaust fan speed added 0
    • dont slow down outer wall added 0
    • during print exhaust fan speed added 100
    • enable pressure advance added 1
    • filament end gcode removed ; filament end gcode
    • filament start gcode removed ; Filament gcode
    • filament vendor Generic → QIDI
    • reduce fan stop start freq 0 → 1
    • textured plate temp added 60
    • textured plate temp initial layer added 60
  49. via parent v5 of fdm_filament_pc — updated
    2026-05-19 12:12
    Settings (30)
    • bed type added Cool Plate
    • eng plate temp 110 → 100
    • eng plate temp initial layer 110 → 100
    • filament cooling final speed removed 0
    • filament cooling initial speed removed 0
    • filament cooling moves removed 0
    • filament deretraction speed added nil
    • filament is support removed 0
    • filament minimal purge on wipe tower 10 → 15
    • filament retract before wipe added nil
    • filament retract restart extra added nil
    • filament retract when changing layer added nil
    • filament retraction length added nil
    • filament retraction minimum travel added nil
    • filament retraction speed added nil
    • filament wipe added nil
    • filament wipe distance added nil
    • filament z hop added nil
    • filament z hop types added nil
    • full fan speed layer added 0
    • hot plate temp 110 → 100
    • hot plate temp initial layer 110 → 100
    • nozzle temperature 280 → 250
    • nozzle temperature initial layer 270 → 250
    • nozzle temperature range high 280 → 290
    • overhang fan speed 60 → 80
    • required nozzle HRC removed 0
    • temperature vitrification 140 → 120
    • textured plate temp added 100
    • textured plate temp initial layer added 100
  50. via parent v4 of fdm_filament_common — updated
    2026-05-19 12:11
    Identity / metadata
    • Material: OTHER → PLA
    Settings (42)
    • bed type added Cool Plate
    • close fan the first x layers added 3
    • cool plate temp added 60
    • cool plate temp initial layer added 60
    • eng plate temp added 60
    • eng plate temp initial layer added 60
    • fan cooling layer time added 60
    • fan max speed added 100
    • fan min speed added 35
    • filament cooling final speed removed 0
    • filament cooling initial speed removed 0
    • filament cooling moves removed 0
    • filament cost added 0
    • filament density added 0
    • filament deretraction speed added nil
    • filament is support removed 0
    • filament max volumetric speed added 0
    • filament minimal purge on wipe tower 10 → 15
    • filament retract before wipe added nil
    • filament retract restart extra added nil
    • filament retract when changing layer added nil
    • filament retraction length added nil
    • filament retraction minimum travel added nil
    • filament retraction speed added nil
    • filament type added PLA
    • filament wipe added nil
    • filament wipe distance added nil
    • filament z hop added nil
    • filament z hop types added nil
    • full fan speed layer added 0
    • hot plate temp added 60
    • hot plate temp initial layer added 60
    • nozzle temperature added 200
    • nozzle temperature initial layer added 200
    • overhang fan speed added 100
    • overhang fan threshold added 95%
    • reduce fan stop start freq added 0
    • required nozzle HRC removed 0
    • slow down for layer cooling added 1
    • slow down layer time added 8
    • slow down min speed added 10
    • temperature vitrification added 100
  51. via parent v4 of fdm_filament_pc — updated
    2026-05-19 12:11
    Settings (38)
    • bed type removed Cool Plate
    • cool plate temp 60 → 0
    • cool plate temp initial layer 60 → 0
    • enable overhang bridge fan removed 1
    • eng plate temp 60 → 110
    • eng plate temp initial layer 60 → 110
    • fan max speed 20 → 60
    • fan min speed 15 → 10
    • filament cooling final speed added 0
    • filament cooling initial speed added 0
    • filament cooling moves added 0
    • filament cost 45 → 20
    • filament density 1.21 → 1.04
    • filament deretraction speed removed nil
    • filament flow ratio 0.94 → 1
    • filament is support added 0
    • filament max volumetric speed 14 → 23.2
    • filament minimal purge on wipe tower 15 → 10
    • filament retract before wipe removed nil
    • filament retract restart extra removed nil
    • filament retract when changing layer removed nil
    • filament retraction length removed nil
    • filament retraction minimum travel removed nil
    • filament retraction speed removed nil
    • filament wipe removed nil
    • filament wipe distance removed nil
    • filament z hop removed nil
    • full fan speed layer removed 3
    • hot plate temp 100 → 110
    • hot plate temp initial layer 100 → 110
    • nozzle temperature 270 → 280
    • reduce fan stop start freq 0 → 1
    • required nozzle HRC added 0
    • slow down layer time 4 → 2
    • slow down min speed 20 → 10
    • support material interface fan speed removed -1
    • textured plate temp removed 60
    • textured plate temp initial layer removed 60
  52. via parent v3 of fdm_filament_common — updated
    2026-05-19 12:10
    Identity / metadata
    • Material: PLA → OTHER
    Settings (43)
    • bed type removed Cool Plate
    • close fan the first x layers removed 3
    • cool plate temp removed 60
    • cool plate temp initial layer removed 60
    • eng plate temp removed 60
    • eng plate temp initial layer removed 60
    • fan cooling layer time removed 60
    • fan max speed removed 100
    • fan min speed removed 35
    • filament cooling final speed added 0
    • filament cooling initial speed added 0
    • filament cooling moves added 0
    • filament cost removed 0
    • filament density removed 0
    • filament deretraction speed removed nil
    • filament is support added 0
    • filament max volumetric speed removed 0
    • filament minimal purge on wipe tower 15 → 10
    • filament retract before wipe removed nil
    • filament retract restart extra removed nil
    • filament retract when changing layer removed nil
    • filament retraction length removed nil
    • filament retraction minimum travel removed nil
    • filament retraction speed removed nil
    • filament type removed PLA
    • filament wipe removed nil
    • filament wipe distance removed nil
    • filament z hop removed nil
    • full fan speed layer removed 0
    • hot plate temp removed 60
    • hot plate temp initial layer removed 60
    • nozzle temperature removed 200
    • nozzle temperature initial layer removed 200
    • overhang fan speed removed 100
    • overhang fan threshold removed 95%
    • reduce fan stop start freq removed 0
    • required nozzle HRC added 0
    • slow down for layer cooling removed 1
    • slow down layer time removed 8
    • slow down min speed removed 10
    • temperature vitrification removed 100
    • textured plate temp removed 60
    • textured plate temp initial layer removed 60
  53. via parent v3 of fdm_filament_pc — updated
    2026-05-19 12:10
    Settings (22)
    • cool plate temp 0 → 60
    • cool plate temp initial layer 0 → 60
    • enable overhang bridge fan added 1
    • eng plate temp 110 → 60
    • eng plate temp initial layer 110 → 60
    • fan max speed 60 → 20
    • fan min speed 10 → 15
    • filament cost 20 → 45
    • filament density 1.04 → 1.21
    • filament flow ratio 1 → 0.94
    • filament max volumetric speed 23.2 → 14
    • filament z hop types removed nil
    • full fan speed layer 0 → 3
    • hot plate temp 110 → 100
    • hot plate temp initial layer 110 → 100
    • nozzle temperature 280 → 270
    • reduce fan stop start freq 1 → 0
    • slow down layer time 2 → 4
    • slow down min speed 10 → 20
    • support material interface fan speed added -1
    • textured plate temp 110 → 60
    • textured plate temp initial layer 110 → 60
  54. via parent v2 of fdm_filament_common — updated
    2026-05-19 12:10
    Settings (1)
    • filament z hop types removed nil
  55. via parent v2 of fdm_filament_pc — updated
    2026-05-19 12:10
    Settings (7)
    • filament flow ratio 0.94 → 1
    • filament id removed OGFC99
    • filament max volumetric speed 12 → 23.2
    • nozzle temperature range high 290 → 280
    • supertack plate temp removed 0
    • supertack plate temp initial layer removed 0
    • temperature vitrification 120 → 140
  56. via parent v1 of fdm_filament_pc — created
    2026-05-19 12:10
    Profile created at this point. No prior version to diff against.
  57. via parent v1 of fdm_filament_common — created
    2026-05-19 12:10
    Profile created at this point. No prior version to diff against.