Prusa Generic PLA Silk @MK4S

Generic · PLA · by elegoo-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Strip G-code from download

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pla

→

Prusa Generic PLA @MK4S

→

Prusa Generic PLA Silk @MK4S

Compatible printers (8)

Prusa MK4S 0.25 nozzle
Prusa MK4S 0.3 nozzle
Prusa MK4S 0.4 nozzle
Prusa MK4S 0.5 nozzle
Prusa MK4S HF0.25 nozzle
Prusa MK4S HF0.3 nozzle
Prusa MK4S HF0.4 nozzle
Prusa MK4S HF0.5 nozzle

Inherited from this (2)

Settings

Basic information

Material variant: PLA inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.24 inherited
Cost (/kg): 25.4 inherited

Print temperature

Nozzle (initial layer) (°C): 230 inherited
Nozzle (other layers) (°C): 225 overridden
was 220 (inherited)

Cooling

Fan minimum (%): 70 inherited
Fan maximum (%): 100 inherited
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 17 inherited
Slow down if layer below (sec): 6 inherited
Min speed when slowed (mm/s): 20 inherited

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 7 overridden
was 15 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	50 inherited	50 inherited
Engineering Plate	50 inherited	50 inherited
High Temp Plate	50 inherited	50 inherited
Textured PEI Plate	50 inherited	50 inherited

Custom G-code

filament_start_gcode overridden

M900 K{if nozzle_diameter[0]==0.4}0.05{elsif nozzle_diameter[0]==0.25}0.14{elsif nozzle_diameter[0]==0.3}0.07{elsif nozzle_diameter[0]==0.35}0.06{elsif nozzle_diameter[0]==0.6}0.03{elsif nozzle_diameter[0]==0.5}0.035{elsif nozzle_diameter[0]==0.8}0.015{else}0{endif} ; Filament gcode

{if printer_notes=~/.*(MK4IS|XLIS|MK4S|MK3.9S).*/}
M572 S{if nozzle_diameter[0]==0.4}0.03{elsif nozzle_diameter[0]==0.5}0.022{elsif nozzle_diameter[0]==0.6}0.018{elsif nozzle_diameter[0]==0.8}0.012{elsif nozzle_diameter[0]==0.25}0.12{elsif nozzle_diameter[0]==0.3}0.075{else}0{endif} ; Filament gcode
{endif}

M142 S36 ; set heatbreak target temp

Other settings

additional cooling fan speed: 0 inherited
bed type: Cool Plate inherited
compatible printers: Prusa MK4S 0.25 nozzle, Prusa MK4S 0.3 nozzle, Prusa MK4S 0.4 nozzle, Prusa MK4S 0.5 nozzle, Prusa MK4S HF0.25 nozzle, Prusa MK4S HF0.3 nozzle, Prusa MK4S HF0.4 nozzle, Prusa MK4S HF0.5 nozzle overridden
was Prusa MK4S 0.25 nozzle, Prusa MK4S 0.3 nozzle, Prusa MK4S 0.4 nozzle, Prusa MK4S 0.5 nozzle (inherited)
default filament colour: #FF8000 inherited
filament id: Generic PLA Silk @MK4S overridden
was Generic PLA @MK4S (inherited)
filament minimal purge on wipe tower: 15 inherited
filament ramming parameters: 250 100 40 40 40 40 40 | 0.05 40 0.45 40 0.95 40 1.45 40 1.95 40 2.45 40 2.95 40 3.45 40 3.95 40 4.45 40 4.95 40 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 3 inherited
instantiation: true overridden
was true (inherited)
nozzle temperature range high: 230 inherited
nozzle temperature range low: 190 inherited
overhang fan speed: 100 inherited
overhang fan threshold: 50% inherited
reduce fan stop start freq: 1 inherited
setting id: GFSA04 overridden
was GFSA04 (inherited)
slow down for layer cooling: 1 inherited
temperature vitrification: 60 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": "70",
  "filament_cost": "25.4",
  "filament_type": [
    "PLA"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "50"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "50"
  ],
  "cool_plate_temp": [
    "50"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.24"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; Filament-specific end gcode"
  ],
  "nozzle_temperature": "225",
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": "20",
  "textured_plate_temp": [
    "50"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "M900 K{if nozzle_diameter[0]==0.4}0.05{elsif nozzle_diameter[0]==0.25}0.14{elsif nozzle_diameter[0]==0.3}0.07{elsif nozzle_diameter[0]==0.35}0.06{elsif nozzle_diameter[0]==0.6}0.03{elsif nozzle_diameter[0]==0.5}0.035{elsif nozzle_diameter[0]==0.8}0.015{else}0{endif} ; Filament gcode\n\n{if printer_notes=~/.*(MK4IS|XLIS|MK4S|MK3.9S).*/}\nM572 S{if nozzle_diameter[0]==0.4}0.03{elsif nozzle_diameter[0]==0.5}0.022{elsif nozzle_diameter[0]==0.6}0.018{elsif nozzle_diameter[0]==0.8}0.012{elsif nozzle_diameter[0]==0.25}0.12{elsif nozzle_diameter[0]==0.3}0.075{else}0{endif} ; Filament gcode\n{endif}\n\nM142 S36 ; set heatbreak target temp"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": "3",
  "slow_down_layer_time": "6",
  "fan_cooling_layer_time": "17",
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "50%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "60"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "50"
  ],
  "cool_plate_temp_initial_layer": [
    "50"
  ],
  "filament_max_volumetric_speed": "7",
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": "230",
  "textured_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "190"
  ],
  "nozzle_temperature_range_high": [
    "230"
  ],
  "setting_id": "GFSA04",
  "filament_id": "Generic PLA Silk @MK4S",
  "filament_notes": [
    ""
  ],
  "compatible_printers": [
    "Prusa MK4S 0.25 nozzle",
    "Prusa MK4S 0.3 nozzle",
    "Prusa MK4S 0.4 nozzle",
    "Prusa MK4S 0.5 nozzle",
    "Prusa MK4S HF0.25 nozzle",
    "Prusa MK4S HF0.3 nozzle",
    "Prusa MK4S HF0.4 nozzle",
    "Prusa MK4S HF0.5 nozzle"
  ],
  "default_filament_colour": "#FF8000",
  "filament_ramming_parameters": [
    "250 100 40 40 40 40 40 | 0.05 40 0.45 40 0.95 40 1.45 40 1.95 40 2.45 40 2.95 40 3.45 40 3.95 40 4.45 40 4.95 40"
  ],
  "name": "Prusa Generic PLA Silk @MK4S"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:46