Flashforge Generic ASA @G3U

Generic · ASA · by elegoo-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_abs

→

Flashforge Generic ABS

→

Flashforge Generic ASA @G3U

Compatible printers (4)

Flashforge Guider 2s 0.4 nozzle
Flashforge Guider 3 Ultra 0.4 Nozzle
Flashforge Guider 3 Ultra 0.6 Nozzle
Flashforge Guider 3 Ultra 0.8 Nozzle

Settings

Basic information

Material variant: ASA overridden
was ABS (inherited)
Vendor: Generic overridden
was Generic (inherited)
Diameter (mm): 1.75 overridden
was 1.75 (inherited)
Density (g/cm³): 1.04 overridden
was 1.04 (inherited)
Cost (/kg): 20 overridden
was 30 (inherited)

Print temperature

Nozzle (initial layer) (°C): 240 overridden
was 250 (inherited)
Nozzle (other layers) (°C): 240 overridden
was 250 (inherited)
Chamber (°C): 0 overridden

Cooling

Fan minimum (%): 10 overridden
was 18 (inherited)
Fan maximum (%): 30 overridden
was 60 (inherited)
Disable fan for first N layers: 2 overridden
was 1 (inherited)
Full fan if layer below (sec): 30 overridden
was 5 (inherited)
Slow down if layer below (sec): 8 overridden
was 8 (inherited)
Min speed when slowed (mm/s): 20 overridden
was 20 (inherited)

Flow

Flow ratio: 1.02 overridden
was 0.98 (inherited)
Max volumetric speed (mm³/s): 18 overridden
was 15 (inherited)

Retraction

Retraction length (mm): nil overridden
was nil (inherited)
Retraction speed (mm/s): nil overridden
was nil (inherited)
Deretraction speed (mm/s): nil overridden
was nil (inherited)

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	80 overridden was 105	80 overridden was 105
Engineering Plate	80 overridden was 105	80 overridden was 105
High Temp Plate	105 overridden was 105	105 overridden was 105
Textured PEI Plate	80 overridden was 105	80 overridden was 105

Other settings

activate air filtration: 0 overridden
activate chamber temp control: 0 overridden
additional cooling fan speed: 0 overridden
was 0 (inherited)
bed type: Cool Plate inherited
compatible printers: Flashforge Guider 3 Ultra 0.4 Nozzle, Flashforge Guider 3 Ultra 0.6 Nozzle, Flashforge Guider 3 Ultra 0.8 Nozzle, Flashforge Guider 2s 0.4 nozzle overridden
was Flashforge Adventurer 5M 0.4 Nozzle, Flashforge Adventurer 5M 0.6 Nozzle, Flashforge Adventurer 5M 0.8 Nozzle, Flashforge Adventurer 5M Pro 0.4 Nozzle, Flashforge Adventurer 5M Pro 0.6 Nozzle, Flashforge Adventurer 5M Pro 0.8 Nozzle, Flashforge AD5X 0.4 nozzle, Flashforge AD5X 0.6 nozzle, Flashforge AD5X 0.8 nozzle (inherited)
complete print exhaust fan speed: 80 overridden
during print exhaust fan speed: 60 overridden
enable overhang bridge fan: 1 overridden
enable pressure advance: 1 overridden
was 1 (inherited)
filament cooling final speed: 3.4 overridden
filament cooling initial speed: 2.2 overridden
filament cooling moves: 4 overridden
filament id: GFB99 overridden
was GFB99 (inherited)
filament is support: 0 overridden
filament load time: 0 overridden
filament loading speed: 28 overridden
filament loading speed start: 3 overridden
filament minimal purge on wipe tower: 10 overridden
was 15 (inherited)
filament multitool ramming: 0 overridden
filament multitool ramming flow: 10 overridden
filament multitool ramming volume: 10 overridden
filament ramming parameters: 120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6 overridden
filament retract before wipe: nil overridden
was nil (inherited)
filament retract lift above: nil overridden
filament retract lift below: nil overridden
filament retract lift enforce: nil overridden
filament retract restart extra: nil overridden
was nil (inherited)
filament retract when changing layer: nil overridden
was nil (inherited)
filament retraction minimum travel: nil overridden
was nil (inherited)
filament shrink: 100% overridden
filament soluble: 0 overridden
was 0 (inherited)
filament toolchange delay: 0 overridden
filament unload time: 0 overridden
filament unloading speed: 35 overridden
filament unloading speed start: 40 overridden
filament wipe: nil overridden
was nil (inherited)
filament wipe distance: nil overridden
was nil (inherited)
filament z hop: nil overridden
was nil (inherited)
filament z hop types: nil overridden
was nil (inherited)
full fan speed layer: 0 overridden
was 0 (inherited)
instantiation: true overridden
was true (inherited)
nozzle temperature range high: 260 overridden
was 280 (inherited)
nozzle temperature range low: 220 overridden
was 240 (inherited)
overhang fan speed: 50 overridden
was 40 (inherited)
overhang fan threshold: 25% overridden
was 25% (inherited)
pressure advance: 0.036 overridden
was 0.04 (inherited)
reduce fan stop start freq: 1 overridden
was 1 (inherited)
required nozzle HRC: 0 overridden
setting id: GFSA04 overridden
was GFSA04 (inherited)
slow down for layer cooling: 1 overridden
was 1 (inherited)
support material interface fan speed: 40 overridden
was 80 (inherited)
temperature vitrification: 100 overridden
was 100 (inherited)

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "30"
  ],
  "fan_min_speed": [
    "10"
  ],
  "filament_cost": [
    "20"
  ],
  "filament_type": [
    "ASA"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "80"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "105"
  ],
  "cool_plate_temp": [
    "80"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.04"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode\n"
  ],
  "nozzle_temperature": [
    "240"
  ],
  "overhang_fan_speed": [
    "50"
  ],
  "filament_flow_ratio": [
    "1.02"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "textured_plate_temp": [
    "80"
  ],
  "filament_settings_id": [
    "Flashforge Generic ASA @G3U"
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "8"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "100"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "2"
  ],
  "eng_plate_temp_initial_layer": [
    "80"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "105"
  ],
  "cool_plate_temp_initial_layer": [
    "80"
  ],
  "filament_max_volumetric_speed": [
    "18"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "240"
  ],
  "textured_plate_temp_initial_layer": [
    "80"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "10"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "220"
  ],
  "nozzle_temperature_range_high": [
    "260"
  ],
  "setting_id": "GFSA04",
  "filament_id": "GFB99",
  "pressure_advance": [
    "0.036"
  ],
  "compatible_printers": [
    "Flashforge Guider 3 Ultra 0.4 Nozzle",
    "Flashforge Guider 3 Ultra 0.6 Nozzle",
    "Flashforge Guider 3 Ultra 0.8 Nozzle",
    "Flashforge Guider 2s 0.4 nozzle"
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "support_material_interface_fan_speed": [
    "40"
  ],
  "filament_notes": [
    ""
  ],
  "filament_shrink": [
    "100%"
  ],
  "compatible_prints": [],
  "filament_load_time": [
    "0"
  ],
  "chamber_temperature": [
    "0"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "0"
  ],
  "filament_unload_time": [
    "0"
  ],
  "filament_cooling_moves": [
    "4"
  ],
  "filament_loading_speed": [
    "28"
  ],
  "activate_air_filtration": [
    "0"
  ],
  "default_filament_colour": [
    ""
  ],
  "filament_unloading_speed": [
    "35"
  ],
  "filament_toolchange_delay": [
    "0"
  ],
  "enable_overhang_bridge_fan": [
    "1"
  ],
  "filament_multitool_ramming": [
    "0"
  ],
  "compatible_prints_condition": "",
  "filament_ramming_parameters": [
    "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
  ],
  "filament_retract_lift_above": [
    "nil"
  ],
  "filament_retract_lift_below": [
    "nil"
  ],
  "filament_cooling_final_speed": [
    "3.4"
  ],
  "filament_loading_speed_start": [
    "3"
  ],
  "activate_chamber_temp_control": [
    "0"
  ],
  "compatible_printers_condition": "",
  "filament_retract_lift_enforce": [
    "nil"
  ],
  "during_print_exhaust_fan_speed": [
    "60"
  ],
  "filament_cooling_initial_speed": [
    "2.2"
  ],
  "filament_unloading_speed_start": [
    "40"
  ],
  "filament_multitool_ramming_flow": [
    "10"
  ],
  "complete_print_exhaust_fan_speed": [
    "80"
  ],
  "filament_multitool_ramming_volume": [
    "10"
  ],
  "name": "Flashforge Generic ASA @G3U"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:45