Flashforge PETG Pro @FF G4P 0.8 HF nozzle

Volumic · PETG · by elegoo-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pet

→

Flashforge Generic PETG

→

Flashforge Generic PETG @G3U 0.6 Nozzle

→

Flashforge PETG Pro @FF G4P 0.8 HF nozzle

Compatible printers (1)

Flashforge Guider4 Pro 0.8 HF nozzle

Settings

Basic information

Material variant: PETG inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.28 overridden
was 1.27 (inherited)
Cost (/kg): 25 overridden
was 30 (inherited)

Print temperature

Nozzle (initial layer) (°C): 245 overridden
was 250 (inherited)
Nozzle (other layers) (°C): 240 overridden
was 250 (inherited)

Cooling

Fan minimum (%): 30 overridden
was 80 (inherited)
Fan maximum (%): 65 overridden
was 100 (inherited)
Disable fan for first N layers: 3 overridden
was 1 (inherited)
Full fan if layer below (sec): 20 overridden
was 30 (inherited)
Slow down if layer below (sec): 10 overridden
was 8 (inherited)
Min speed when slowed (mm/s): 20 overridden
was 12 (inherited)

Flow

Flow ratio: 0.96 overridden
was 1.01 (inherited)
Max volumetric speed (mm³/s): 25 overridden
was 12 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	0 overridden was 60	0 overridden was 60
Textured Cool Plate	80 overridden	80 overridden
Engineering Plate	80 overridden was 70	80 overridden was 0
High Temp Plate	80 overridden was 75	80 overridden was 75
Textured PEI Plate	80 overridden was 70	80 overridden was 80

Other settings

additional cooling fan speed: 40 overridden
was 50 (inherited)
bed type: Cool Plate inherited
compatible printers: Flashforge Guider4 Pro 0.8 HF nozzle overridden
was Flashforge Guider 3 Ultra 0.6 Nozzle (inherited)
complete print exhaust fan speed: 40 overridden
during print exhaust fan speed: 40 overridden
enable pressure advance: 1 inherited
filament id: GFB99 inherited
filament minimal purge on wipe tower: 15 overridden
was 5 (inherited)
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament unloading speed: 35 inherited
filament unloading speed start: 40 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was true (inherited)
nozzle temperature range high: 265 overridden
was 260 (inherited)
nozzle temperature range low: 220 overridden
was 230 (inherited)
overhang fan speed: 100 overridden
was 80 (inherited)
overhang fan threshold: 25% inherited
pressure advance: 0.042 inherited
reduce fan stop start freq: 1 inherited
setting id: GFSA04 inherited
slow down for layer cooling: 1 inherited
support material interface fan speed: 100 overridden
was 90 (inherited)
temperature vitrification: 70 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "65"
  ],
  "fan_min_speed": [
    "30"
  ],
  "filament_cost": [
    "25"
  ],
  "filament_type": [
    "PETG"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "80"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "80"
  ],
  "cool_plate_temp": [
    "0"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.28"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode\n"
  ],
  "nozzle_temperature": [
    "240"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "0.96"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "textured_plate_temp": [
    "80"
  ],
  "filament_settings_id": [
    "Flashforge PETG Pro @FF G4P 0.8 HF nozzle"
  ],
  "filament_start_gcode": [
    "; filament start gcode\n;right_extruder_material:PETG"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "10"
  ],
  "fan_cooling_layer_time": [
    "20"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "70"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "80"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "80"
  ],
  "cool_plate_temp_initial_layer": [
    "0"
  ],
  "filament_max_volumetric_speed": [
    "25"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "245"
  ],
  "textured_plate_temp_initial_layer": [
    "80"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "220"
  ],
  "nozzle_temperature_range_high": [
    "265"
  ],
  "setting_id": "GFSA04",
  "filament_id": "GFB99",
  "pressure_advance": [
    "0.042"
  ],
  "compatible_printers": [
    "Flashforge Guider4 Pro 0.8 HF nozzle"
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "additional_cooling_fan_speed": [
    "40"
  ],
  "support_material_interface_fan_speed": [
    "100"
  ],
  "filament_unloading_speed": [
    "35"
  ],
  "filament_unloading_speed_start": [
    "40"
  ],
  "textured_cool_plate_temp": [
    "80"
  ],
  "during_print_exhaust_fan_speed": [
    "40"
  ],
  "complete_print_exhaust_fan_speed": [
    "40"
  ],
  "textured_cool_plate_temp_initial_layer": [
    "80"
  ],
  "name": "Flashforge PETG Pro @FF G4P 0.8 HF nozzle"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:45