Flashforge PA @FF G4P 0.6 HF nozzle

Volumic · PA · by elegoo-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pla

→

Flashforge Generic PLA

→

Flashforge Generic PLA @G3U 0.6 Nozzle

→

Flashforge PA @FF G4P 0.6 HF nozzle

Compatible printers (1)

Flashforge Guider4 Pro 0.6 HF nozzle

Settings

Basic information

Material variant: PA overridden
was PLA (inherited)
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.04 overridden
was 1.24 (inherited)
Cost (/kg): 30 inherited

Print temperature

Nozzle (initial layer) (°C): 290 overridden
was 220 (inherited)
Nozzle (other layers) (°C): 290 overridden
was 220 (inherited)
Chamber (°C): 60 overridden

Cooling

Fan minimum (%): 50 overridden
was 100 (inherited)
Fan maximum (%): 80 overridden
was 100 (inherited)
Disable fan for first N layers: 2 overridden
was 1 (inherited)
Full fan if layer below (sec): 30 overridden
was 50 (inherited)
Slow down if layer below (sec): 8 overridden
was 15 (inherited)
Min speed when slowed (mm/s): 15 inherited

Flow

Flow ratio: 0.96 overridden
was 0.99 (inherited)
Max volumetric speed (mm³/s): 15 overridden
was 20 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	0 overridden was 50	0 overridden was 50
Textured Cool Plate	0 overridden	0 overridden
Engineering Plate	105 overridden was 50	105 overridden was 50
High Temp Plate	105 overridden was 55	105 overridden was 55
Textured PEI Plate	105 overridden was 50	105 overridden was 50

Other settings

activate chamber temp control: 1 overridden
additional cooling fan speed: 0 overridden
was 80 (inherited)
bed type: Cool Plate inherited
compatible printers: Flashforge Guider4 Pro 0.6 HF nozzle overridden
was Flashforge Guider 3 Ultra 0.6 Nozzle (inherited)
complete print exhaust fan speed: 40 overridden
during print exhaust fan speed: 40 overridden
enable pressure advance: 1 inherited
filament id: FFG01 inherited
filament minimal purge on wipe tower: 15 overridden
was 5 (inherited)
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament unloading speed: 40 inherited
filament unloading speed start: 40 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 295 overridden
was 230 (inherited)
nozzle temperature range low: 240 overridden
was 200 (inherited)
overhang fan speed: 80 overridden
was 100 (inherited)
overhang fan threshold: 25% overridden
was 50% (inherited)
pressure advance: 0.023 overridden
was 0.042 (inherited)
reduce fan stop start freq: 1 inherited
setting id: FFGP02_01 inherited
slow down for layer cooling: 1 inherited
support material interface fan speed: 80 overridden
was 100 (inherited)
temperature vitrification: 108 overridden
was 60 (inherited)

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "80"
  ],
  "fan_min_speed": [
    "50"
  ],
  "filament_cost": [
    "30"
  ],
  "filament_type": [
    "PA"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "105"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "105"
  ],
  "cool_plate_temp": [
    "0"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.04"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode\n"
  ],
  "nozzle_temperature": [
    "290"
  ],
  "overhang_fan_speed": [
    "80"
  ],
  "filament_flow_ratio": [
    "0.96"
  ],
  "slow_down_min_speed": [
    "15"
  ],
  "textured_plate_temp": [
    "105"
  ],
  "filament_settings_id": [
    "Flashforge PA @FF G4P 0.6 HF nozzle"
  ],
  "filament_start_gcode": [
    "; filament start gcode\n; right_extruder_material:PA\n\n\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "8"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "108"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "2"
  ],
  "eng_plate_temp_initial_layer": [
    "105"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "105"
  ],
  "cool_plate_temp_initial_layer": [
    "0"
  ],
  "filament_max_volumetric_speed": [
    "15"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "290"
  ],
  "textured_plate_temp_initial_layer": [
    "105"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "240"
  ],
  "nozzle_temperature_range_high": [
    "295"
  ],
  "setting_id": "FFGP02_01",
  "filament_id": "FFG01",
  "pressure_advance": [
    "0.023"
  ],
  "compatible_printers": [
    "Flashforge Guider4 Pro 0.6 HF nozzle"
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "support_material_interface_fan_speed": [
    "80"
  ],
  "filament_unloading_speed": [
    "40"
  ],
  "filament_unloading_speed_start": [
    "40"
  ],
  "chamber_temperature": [
    "60"
  ],
  "textured_cool_plate_temp": [
    "0"
  ],
  "activate_chamber_temp_control": [
    "1"
  ],
  "during_print_exhaust_fan_speed": [
    "40"
  ],
  "complete_print_exhaust_fan_speed": [
    "40"
  ],
  "textured_cool_plate_temp_initial_layer": [
    "0"
  ],
  "name": "Flashforge PA @FF G4P 0.6 HF nozzle"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:45