Flashforge PETG Pro @FF AD5X

Volumic · PETG · by elegoo-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pet

→

Flashforge Generic PETG

→

Flashforge PETG Pro @FF AD5X

Compatible printers (1)

Flashforge AD5X 0.4 nozzle

Settings

Basic information

Material variant: PETG inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.27 inherited
Cost (/kg): 30 inherited

Print temperature

Nozzle (initial layer) (°C): 265 overridden
was 255 (inherited)
Nozzle (other layers) (°C): 265 overridden
was 255 (inherited)

Cooling

Fan minimum (%): 10 overridden
was 80 (inherited)
Fan maximum (%): 50 overridden
was 100 (inherited)
Disable fan for first N layers: 2 overridden
was 1 (inherited)
Full fan if layer below (sec): 30 inherited
Slow down if layer below (sec): 12 overridden
was 8 (inherited)
Min speed when slowed (mm/s): 30 inherited

Flow

Flow ratio: 0.98 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 10 overridden
was 12 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	0 overridden was 60	0 overridden was 60
Textured Cool Plate	75 overridden	75 overridden
Engineering Plate	75 overridden was 70	75 overridden was 0
High Temp Plate	75 overridden was 70	75 overridden was 70
Textured PEI Plate	75 overridden was 70	75 overridden was 80

Other settings

additional cooling fan speed: 50 inherited
bed type: Cool Plate inherited
compatible printers: Flashforge AD5X 0.4 nozzle overridden
was Flashforge Adventurer 5M 0.4 Nozzle, Flashforge Adventurer 5M 0.6 Nozzle, Flashforge Adventurer 5M 0.8 Nozzle, Flashforge Adventurer 5M Pro 0.4 Nozzle, Flashforge Adventurer 5M Pro 0.6 Nozzle, Flashforge Adventurer 5M Pro 0.8 Nozzle, Flashforge AD5X 0.4 nozzle, Flashforge AD5X 0.6 nozzle, Flashforge AD5X 0.8 nozzle (inherited)
enable pressure advance: 1 inherited
filament id: GFG99 inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was true (inherited)
nozzle temperature range high: 270 overridden
was 260 (inherited)
nozzle temperature range low: 220 inherited
overhang fan speed: 90 overridden
was 80 (inherited)
overhang fan threshold: 10% overridden
was 25% (inherited)
pressure advance: 0.04 overridden
was 0.046 (inherited)
reduce fan stop start freq: 1 inherited
setting id: GFSA04 overridden
was GFSA04 (inherited)
slow down for layer cooling: 1 inherited
support material interface fan speed: 90 inherited
temperature vitrification: 70 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "50"
  ],
  "fan_min_speed": [
    "10"
  ],
  "filament_cost": [
    "30"
  ],
  "filament_type": [
    "PETG"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "75"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "75"
  ],
  "cool_plate_temp": [
    "0"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.27"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode\n"
  ],
  "nozzle_temperature": [
    "265"
  ],
  "overhang_fan_speed": [
    "90"
  ],
  "filament_flow_ratio": [
    "0.98"
  ],
  "slow_down_min_speed": [
    "30"
  ],
  "textured_plate_temp": [
    "75"
  ],
  "filament_settings_id": [
    "Flashforge PETG Pro @FF AD5X"
  ],
  "filament_start_gcode": [
    "; filament start gcode \n;right_extruder_material:PETG"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "12"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "10%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "70"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "2"
  ],
  "eng_plate_temp_initial_layer": [
    "75"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "75"
  ],
  "cool_plate_temp_initial_layer": [
    "0"
  ],
  "filament_max_volumetric_speed": [
    "10"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "265"
  ],
  "textured_plate_temp_initial_layer": [
    "75"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "220"
  ],
  "nozzle_temperature_range_high": [
    "270"
  ],
  "setting_id": "GFSA04",
  "filament_id": "GFG99",
  "pressure_advance": [
    "0.04"
  ],
  "compatible_printers": [
    "Flashforge AD5X 0.4 nozzle"
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "additional_cooling_fan_speed": [
    "50"
  ],
  "support_material_interface_fan_speed": [
    "90"
  ],
  "textured_cool_plate_temp": [
    "75"
  ],
  "textured_cool_plate_temp_initial_layer": [
    "75"
  ],
  "name": "Flashforge PETG Pro @FF AD5X"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:43