Flashforge TPU 95A @FF G4 0.6 HF nozzle

Volumic · TPU · by elegoo-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pet

→

Flashforge Generic PETG

→

Flashforge Generic PETG @G3U 0.6 Nozzle

→

Flashforge TPU 95A @FF G4 0.6 HF nozzle

Compatible printers (1)

Flashforge Guider4 0.6 HF nozzle

Settings

Basic information

Material variant: TPU overridden
was PETG (inherited)
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.22 overridden
was 1.27 (inherited)
Cost (/kg): 40 overridden
was 30 (inherited)

Print temperature

Nozzle (initial layer) (°C): 220 overridden
was 250 (inherited)
Nozzle (other layers) (°C): 220 overridden
was 250 (inherited)

Cooling

Fan minimum (%): 100 overridden
was 80 (inherited)
Fan maximum (%): 100 inherited
Disable fan for first N layers: 3 overridden
was 1 (inherited)
Full fan if layer below (sec): 100 overridden
was 30 (inherited)
Slow down if layer below (sec): 8 inherited
Min speed when slowed (mm/s): 20 overridden
was 12 (inherited)

Flow

Flow ratio: 0.98 overridden
was 1.01 (inherited)
Max volumetric speed (mm³/s): 8 overridden
was 12 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	40 overridden was 60	40 overridden was 60
Textured Cool Plate	45 overridden	45 overridden
Engineering Plate	50 overridden was 70	50 overridden was 0
High Temp Plate	50 overridden was 75	50 overridden was 75
Textured PEI Plate	50 overridden was 70	50 overridden was 80

Other settings

additional cooling fan speed: 40 overridden
was 50 (inherited)
bed type: Cool Plate inherited
compatible printers: Flashforge Guider4 0.6 HF nozzle overridden
was Flashforge Guider 3 Ultra 0.6 Nozzle (inherited)
complete print exhaust fan speed: 40 overridden
during print exhaust fan speed: 40 overridden
enable pressure advance: 1 inherited
filament id: GFB99 inherited
filament minimal purge on wipe tower: 15 overridden
was 5 (inherited)
filament ramming parameters: 105 105 6.62366 6.75269 6.98925 7.5914 8.94624 10.9892 13.2903 15.2043 16.129 16.2366 16.1505 16.1075 16.0645 16.0215 16.0215 16.0215 15.957 15.8495 15.8065 15.8495| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 11.7839 1.95 15.8075 2.45 16.1936 2.95 16.1162 3.45 16.0301 3.95 16.0301 4.45 15.8151 4.95 15.9011 overridden
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament unloading speed: 35 inherited
filament unloading speed start: 40 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was true (inherited)
nozzle temperature range high: 250 overridden
was 260 (inherited)
nozzle temperature range low: 190 overridden
was 230 (inherited)
overhang fan speed: 100 overridden
was 80 (inherited)
overhang fan threshold: 25% inherited
pressure advance: 0.03 overridden
was 0.042 (inherited)
reduce fan stop start freq: 1 inherited
setting id: GFSA04 inherited
slow down for layer cooling: 1 inherited
support material interface fan speed: 100 overridden
was 90 (inherited)
temperature vitrification: 30 overridden
was 70 (inherited)

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_cost": [
    "40"
  ],
  "filament_type": [
    "TPU"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "50"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "50"
  ],
  "cool_plate_temp": [
    "40"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.22"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode\n"
  ],
  "nozzle_temperature": [
    "220"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "0.98"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "textured_plate_temp": [
    "50"
  ],
  "filament_settings_id": [
    "Flashforge TPU 95A @FF G4 0.6 HF nozzle"
  ],
  "filament_start_gcode": [
    "; filament start gcode\n; right_extruder_material:TPU"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "8"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "30"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "50"
  ],
  "cool_plate_temp_initial_layer": [
    "40"
  ],
  "filament_max_volumetric_speed": [
    "8"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "220"
  ],
  "textured_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "190"
  ],
  "nozzle_temperature_range_high": [
    "250"
  ],
  "setting_id": "GFSA04",
  "filament_id": "GFB99",
  "pressure_advance": [
    "0.03"
  ],
  "compatible_printers": [
    "Flashforge Guider4 0.6 HF nozzle"
  ],
  "enable_pressure_advance": [
    "1"
  ],
  "additional_cooling_fan_speed": [
    "40"
  ],
  "support_material_interface_fan_speed": [
    "100"
  ],
  "filament_unloading_speed": [
    "35"
  ],
  "filament_unloading_speed_start": [
    "40"
  ],
  "textured_cool_plate_temp": [
    "45"
  ],
  "filament_ramming_parameters": [
    "105 105 6.62366 6.75269 6.98925 7.5914 8.94624 10.9892 13.2903 15.2043 16.129 16.2366 16.1505 16.1075 16.0645 16.0215 16.0215 16.0215 15.957 15.8495 15.8065 15.8495| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 11.7839 1.95 15.8075 2.45 16.1936 2.95 16.1162 3.45 16.0301 3.95 16.0301 4.45 15.8151 4.95 15.9011"
  ],
  "during_print_exhaust_fan_speed": [
    "40"
  ],
  "complete_print_exhaust_fan_speed": [
    "40"
  ],
  "textured_cool_plate_temp_initial_layer": [
    "45"
  ],
  "name": "Flashforge TPU 95A @FF G4 0.6 HF nozzle"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:43