CoPrint Generic ABS

Co Print · ABS · by elegoo-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pla

→

CoPrint Generic PLA

→

CoPrint Generic ABS

Compatible printers (4)

Co Print ChromaSet 0.4 nozzle
Co Print ChromaSet 0.4 nozzle - Ender-3 V3
Co Print ChromaSet 0.4 nozzle - Ender-3 V3 Plus
Co Print ChromaSet 0.4 nozzle fast

Settings

Basic information

Material variant: ABS overridden
was PLA (inherited)
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.04 overridden
was 1.24 (inherited)
Cost (/kg): 30 inherited

Print temperature

Nozzle (initial layer) (°C): 260 overridden
was 220 (inherited)
Nozzle (other layers) (°C): 280 overridden
was 220 (inherited)

Cooling

Fan minimum (%): 10 overridden
was 100 (inherited)
Fan maximum (%): 60 overridden
was 100 (inherited)
Disable fan for first N layers: 3 overridden
was 1 (inherited)
Full fan if layer below (sec): 30 overridden
was 100 (inherited)
Slow down if layer below (sec): 12 overridden
was 5 (inherited)
Min speed when slowed (mm/s): 20 overridden
was 5 (inherited)

Flow

Flow ratio: 0.94 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 16 overridden
was 20 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	50 inherited	50 inherited
Engineering Plate	50 inherited	50 inherited
High Temp Plate	100 overridden was 50	100 overridden was 50
Textured PEI Plate	50 inherited	50 inherited

Other settings

additional cooling fan speed: 0 inherited
bed type: Cool Plate inherited
compatible printers: Co Print ChromaSet 0.4 nozzle, Co Print ChromaSet 0.4 nozzle - Ender-3 V3, Co Print ChromaSet 0.4 nozzle - Ender-3 V3 Plus, Co Print ChromaSet 0.4 nozzle fast overridden
was Co Print ChromaSet 0.4 nozzle, Co Print ChromaSet 0.4 nozzle - Ender-3 V3, Co Print ChromaSet 0.4 nozzle - Ender-3 V3 Plus, Co Print ChromaSet 0.4 nozzle fast (inherited)
filament id: GFL99 overridden
was GFL99 (inherited)
filament load time: 9.75 inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament unload time: 9.75 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 5 overridden
was 0 (inherited)
instantiation: true overridden
was true (inherited)
nozzle temperature range high: 280 overridden
was 230 (inherited)
nozzle temperature range low: 240 overridden
was 190 (inherited)
overhang fan speed: 100 inherited
overhang fan threshold: 25% overridden
was 50% (inherited)
pressure advance: 0.02 overridden
reduce fan stop start freq: 1 inherited
setting id: GFSA04 overridden
was GFSA04 (inherited)
slow down for layer cooling: 1 inherited
temperature vitrification: 100 overridden
was 60 (inherited)

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "60"
  ],
  "fan_min_speed": [
    "10"
  ],
  "filament_cost": [
    "30"
  ],
  "filament_type": [
    "ABS"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "50"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "100"
  ],
  "cool_plate_temp": [
    "50"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.04"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "280"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "0.94"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "textured_plate_temp": [
    "50"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "5"
  ],
  "slow_down_layer_time": [
    "12"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "100"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "100"
  ],
  "cool_plate_temp_initial_layer": [
    "50"
  ],
  "filament_max_volumetric_speed": [
    "16"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "260"
  ],
  "textured_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "240"
  ],
  "nozzle_temperature_range_high": [
    "280"
  ],
  "setting_id": "GFSA04",
  "filament_id": "GFL99",
  "filament_load_time": [
    "9.75"
  ],
  "compatible_printers": [
    "Co Print ChromaSet 0.4 nozzle",
    "Co Print ChromaSet 0.4 nozzle - Ender-3 V3",
    "Co Print ChromaSet 0.4 nozzle - Ender-3 V3 Plus",
    "Co Print ChromaSet 0.4 nozzle fast"
  ],
  "filament_unload_time": [
    "9.75"
  ],
  "pressure_advance": [
    "0.02"
  ],
  "name": "CoPrint Generic ABS"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:43