Fiberon PA6-GF @BBL X1C

Polymaker · PA-GF · by elegoo-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pa

→

Fiberon PA6-GF @base

→

Fiberon PA6-GF @BBL X1C

Compatible printers (6)

Bambu Lab P1S 0.4 nozzle
Bambu Lab P1S 0.6 nozzle
Bambu Lab P1S 0.8 nozzle
Bambu Lab X1 Carbon 0.4 nozzle
Bambu Lab X1 Carbon 0.6 nozzle
Bambu Lab X1 Carbon 0.8 nozzle

Settings

Basic information

Material variant: PA-GF inherited
Vendor: Polymaker inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.2 inherited
Cost (/kg): 63.99 inherited

Print temperature

Nozzle (initial layer) (°C): 300 inherited
Nozzle (other layers) (°C): 300 inherited

Cooling

Fan minimum (%): 0 inherited
Fan maximum (%): 100 inherited
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 15 inherited
Slow down if layer below (sec): 2 inherited
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 0.95 inherited
Max volumetric speed (mm³/s): 12 inherited

Retraction

Retraction length (mm): 1.0 inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	0 inherited	0 inherited
Engineering Plate	40 inherited	40 inherited
High Temp Plate	40 inherited	40 inherited
Textured PEI Plate	40 inherited	40 inherited

Other settings

bed type: Cool Plate inherited
compatible printers: Bambu Lab P1S 0.4 nozzle, Bambu Lab P1S 0.6 nozzle, Bambu Lab P1S 0.8 nozzle, Bambu Lab X1 Carbon 0.4 nozzle, Bambu Lab X1 Carbon 0.6 nozzle, Bambu Lab X1 Carbon 0.8 nozzle overridden
filament id: OGFL51 inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: 0.0 inherited
filament z hop types: nil inherited
full fan speed layer: 2 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 300 inherited
nozzle temperature range low: 280 inherited
overhang fan speed: 100 inherited
overhang fan threshold: 95% inherited
reduce fan stop start freq: 1 inherited
setting id: GFSL51_00 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 191 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "0"
  ],
  "filament_cost": [
    "63.99"
  ],
  "filament_type": [
    "PA-GF"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "40"
  ],
  "filament_z_hop": [
    "0.0"
  ],
  "hot_plate_temp": [
    "40"
  ],
  "cool_plate_temp": [
    "0"
  ],
  "filament_vendor": [
    "Polymaker"
  ],
  "filament_density": [
    "1.2"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "300"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "0.95"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "textured_plate_temp": [
    "40"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; Filament gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "2"
  ],
  "slow_down_layer_time": [
    "2"
  ],
  "fan_cooling_layer_time": [
    "15"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "95%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "191"
  ],
  "filament_retraction_length": [
    "1.0"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "40"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "40"
  ],
  "cool_plate_temp_initial_layer": [
    "0"
  ],
  "filament_max_volumetric_speed": [
    "12"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "300"
  ],
  "textured_plate_temp_initial_layer": [
    "40"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "280"
  ],
  "nozzle_temperature_range_high": [
    "300"
  ],
  "filament_id": "OGFL51",
  "setting_id": "GFSL51_00",
  "compatible_printers": [
    "Bambu Lab P1S 0.4 nozzle",
    "Bambu Lab P1S 0.6 nozzle",
    "Bambu Lab P1S 0.8 nozzle",
    "Bambu Lab X1 Carbon 0.4 nozzle",
    "Bambu Lab X1 Carbon 0.6 nozzle",
    "Bambu Lab X1 Carbon 0.8 nozzle"
  ],
  "name": "Fiberon PA6-GF @BBL X1C"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:40