Generic EVA @BBL X1C

Generic · EVA · by elegoo-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Strip G-code from download

Compare

Inheritance

fdm_filament_common

→

fdm_filament_eva

→

Generic EVA @base

→

Generic EVA @BBL X1C

Compatible printers (15)

Bambu Lab P1P 0.4 nozzle
Bambu Lab P1P 0.6 nozzle
Bambu Lab P1P 0.8 nozzle
Bambu Lab P1S 0.4 nozzle
Bambu Lab P1S 0.6 nozzle
Bambu Lab P1S 0.8 nozzle
Bambu Lab X1 0.4 nozzle
Bambu Lab X1 0.6 nozzle
Bambu Lab X1 0.8 nozzle
Bambu Lab X1 Carbon 0.4 nozzle
Bambu Lab X1 Carbon 0.6 nozzle
Bambu Lab X1 Carbon 0.8 nozzle
Bambu Lab X1E 0.4 nozzle
Bambu Lab X1E 0.6 nozzle
Bambu Lab X1E 0.8 nozzle

Settings

Basic information

Material variant: EVA inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 0.94 inherited
Cost (/kg): 21.99 inherited

Print temperature

Nozzle (initial layer) (°C): 210 inherited
Nozzle (other layers) (°C): 210 inherited

Cooling

Fan minimum (%): 100 inherited
Fan maximum (%): 100 inherited
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 100 inherited
Slow down if layer below (sec): 4 inherited
Min speed when slowed (mm/s): 20 inherited

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 12 inherited

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	35 inherited	35 inherited
Engineering Plate	0 inherited	0 inherited
High Temp Plate	55 inherited	55 inherited
Textured PEI Plate	55 inherited	55 inherited
Cool Plate SuperTack	0 inherited	0 inherited

Custom G-code

filament_start_gcode inherited

; filament start gcode
{if  (bed_temperature[current_extruder] >55)||(bed_temperature_initial_layer[current_extruder] >55)}M106 P3 S200
{elsif(bed_temperature[current_extruder] >50)||(bed_temperature_initial_layer[current_extruder] >50)}M106 P3 S150
{elsif(bed_temperature[current_extruder] >45)||(bed_temperature_initial_layer[current_extruder] >45)}M106 P3 S50
{endif}

{if activate_air_filtration[current_extruder] && support_air_filtration}
M106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} 
{endif}

Other settings

additional cooling fan speed: 70 inherited
bed type: Cool Plate inherited
compatible printers: Bambu Lab P1P 0.4 nozzle, Bambu Lab P1P 0.6 nozzle, Bambu Lab P1P 0.8 nozzle, Bambu Lab P1S 0.4 nozzle, Bambu Lab P1S 0.6 nozzle, Bambu Lab P1S 0.8 nozzle, Bambu Lab X1 0.4 nozzle, Bambu Lab X1 0.6 nozzle, Bambu Lab X1 0.8 nozzle, Bambu Lab X1 Carbon 0.4 nozzle, Bambu Lab X1 Carbon 0.6 nozzle, Bambu Lab X1 Carbon 0.8 nozzle, Bambu Lab X1E 0.4 nozzle, Bambu Lab X1E 0.6 nozzle, Bambu Lab X1E 0.8 nozzle overridden
description: This is neither a commonly used filament, nor one of Bambu filaments, and it varies a lot from brand to brand. So, it's highly recommended to ask its vendor for suitable profile before printing and adjust some parameters according to its performances. overridden
filament id: GFR99 inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 220 inherited
nozzle temperature range low: 175 inherited
overhang fan speed: 100 inherited
overhang fan threshold: 50% inherited
reduce fan stop start freq: 1 inherited
setting id: GFSR99_00 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 70 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "100"
  ],
  "filament_cost": [
    "21.99"
  ],
  "filament_type": [
    "EVA"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "0"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "55"
  ],
  "cool_plate_temp": [
    "35"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "0.94"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "210"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "textured_plate_temp": [
    "55"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n{if  (bed_temperature[current_extruder] >55)||(bed_temperature_initial_layer[current_extruder] >55)}M106 P3 S200\n{elsif(bed_temperature[current_extruder] >50)||(bed_temperature_initial_layer[current_extruder] >50)}M106 P3 S150\n{elsif(bed_temperature[current_extruder] >45)||(bed_temperature_initial_layer[current_extruder] >45)}M106 P3 S50\n{endif}\n\n{if activate_air_filtration[current_extruder] && support_air_filtration}\nM106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} \n{endif}"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "4"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "50%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "70"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "0"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "55"
  ],
  "cool_plate_temp_initial_layer": [
    "35"
  ],
  "filament_max_volumetric_speed": [
    "12"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "210"
  ],
  "textured_plate_temp_initial_layer": [
    "55"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "filament_id": "GFR99",
  "supertack_plate_temp": [
    "0"
  ],
  "supertack_plate_temp_initial_layer": [
    "0"
  ],
  "additional_cooling_fan_speed": [
    "70"
  ],
  "nozzle_temperature_range_low": [
    "175"
  ],
  "nozzle_temperature_range_high": [
    "220"
  ],
  "setting_id": "GFSR99_00",
  "description": "This is neither a commonly used filament, nor one of Bambu filaments, and it varies a lot from brand to brand. So, it's highly recommended to ask its vendor for suitable profile before printing and adjust some parameters according to its performances.",
  "compatible_printers": [
    "Bambu Lab P1P 0.4 nozzle",
    "Bambu Lab P1P 0.6 nozzle",
    "Bambu Lab P1P 0.8 nozzle",
    "Bambu Lab P1S 0.4 nozzle",
    "Bambu Lab P1S 0.6 nozzle",
    "Bambu Lab P1S 0.8 nozzle",
    "Bambu Lab X1 0.4 nozzle",
    "Bambu Lab X1 0.6 nozzle",
    "Bambu Lab X1 0.8 nozzle",
    "Bambu Lab X1 Carbon 0.4 nozzle",
    "Bambu Lab X1 Carbon 0.6 nozzle",
    "Bambu Lab X1 Carbon 0.8 nozzle",
    "Bambu Lab X1E 0.4 nozzle",
    "Bambu Lab X1E 0.6 nozzle",
    "Bambu Lab X1E 0.8 nozzle"
  ],
  "name": "Generic EVA @BBL X1C"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:39