Bambu PETG Translucent @BBL X1C 0.8 nozzle

Bambu Lab · PETG · 0.80mm nozzle · by bambu-system · 1 download

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Strip G-code from download

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pet

→

Bambu PETG Translucent @base

→

Bambu PETG Translucent @BBL X1C 0.8 nozzle

Includes (1)

Bambu-only mechanism: these template profiles contribute settings on top of the inheritance chain, before this profile's own overrides. Values pulled in via an include are tagged via <template> in the panels below.

fdm_filament_template_direct_dual

Compatible printers (7)

Bambu Lab P1P 0.8 nozzle
Bambu Lab P1S 0.8 nozzle
Bambu Lab X1 0.6 nozzle
Bambu Lab X1 0.8 nozzle
Bambu Lab X1 Carbon 0.8 nozzle
Bambu Lab X1E 0.6 nozzle
Bambu Lab X1E 0.8 nozzle

Settings

Basic information

Material variant: PETG inherited
Vendor: Bambu Lab inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.25 inherited
Cost (/kg): 24.99 inherited

Print temperature

Nozzle (initial layer) (°C): 250 overridden
was 250 (inherited)
Nozzle (other layers) (°C): 245 overridden
was 245 (inherited)

Cooling

Fan minimum (%): 20 overridden
was 10 (inherited)
Fan maximum (%): 60 overridden
was 30 (inherited)
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 30 inherited
Slow down if layer below (sec): 8 overridden
was 12 (inherited)
Min speed when slowed (mm/s): 10 via fdm_filament_template_direct_dual

Flow

Flow ratio: 0.95 via fdm_filament_template_direct_dual
Max volumetric speed (mm³/s): 16 overridden
was 6 (inherited)

Retraction

Retraction length (mm): 0.2 overridden
was nil (inherited)
Retraction speed (mm/s): nil via fdm_filament_template_direct_dual
Deretraction speed (mm/s): nil via fdm_filament_template_direct_dual

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	0 inherited	0 inherited
Engineering Plate	70 inherited	70 inherited
High Temp Plate	70 inherited	70 inherited
Textured PEI Plate	70 inherited	70 inherited

Custom G-code

filament_start_gcode inherited

; filament start gcode
{if (bed_temperature[current_extruder] >80)||(bed_temperature_initial_layer[current_extruder] >80)}M106 P3 S255
{elsif (bed_temperature[current_extruder] >60)||(bed_temperature_initial_layer[current_extruder] >60)}M106 P3 S180
{endif}

{if activate_air_filtration[current_extruder] && support_air_filtration}
M106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} 
{endif}

Other settings

additional fan full speed layer: 0 inherited
close additional fan first x layers: 3 inherited
compatible printers: Bambu Lab X1 Carbon 0.8 nozzle, Bambu Lab X1 0.6 nozzle, Bambu Lab X1 0.8 nozzle, Bambu Lab P1P 0.8 nozzle, Bambu Lab P1S 0.8 nozzle, Bambu Lab X1E 0.6 nozzle, Bambu Lab X1E 0.8 nozzle overridden
description: To get better transparent or translucent results with the corresponding filament, please refer to this wiki: Printing tips for transparent PETG. inherited
filament adaptive volumetric speed: 0, 0 via fdm_filament_template_direct_dual
filament bridge speed: 25, 25 via fdm_filament_template_direct_dual
filament cooling before tower: 0, 0 via fdm_filament_template_direct_dual
filament enable overhang speed: 1, 1 via fdm_filament_template_direct_dual
filament extruder variant: Direct Drive Standard, Direct Drive High Flow via fdm_filament_template_direct_dual
filament flush temp: 0, 0 via fdm_filament_template_direct_dual
filament flush volumetric speed: 0, 0 via fdm_filament_template_direct_dual
filament id: GFG01 inherited
filament is support: 0 inherited
filament long retractions when cut: 1, 1 overridden
filament metal stickiness: High inherited
filament minimal purge on wipe tower: 15 inherited
filament overhang 1 4 speed: 0, 0 via fdm_filament_template_direct_dual
filament overhang 2 4 speed: 50, 50 via fdm_filament_template_direct_dual
filament overhang 3 4 speed: 30, 30 via fdm_filament_template_direct_dual
filament overhang 4 4 speed: 10, 10 via fdm_filament_template_direct_dual
filament overhang totally speed: 10, 10 via fdm_filament_template_direct_dual
filament pre cooling temperature: 0, 0 via fdm_filament_template_direct_dual
filament pre cooling temperature nc: 0, 0 via fdm_filament_template_direct_dual
filament ramming travel time: 0, 0 overridden
filament ramming travel time nc: 0, 0 via fdm_filament_template_direct_dual
filament ramming volumetric speed: -1, -1 via fdm_filament_template_direct_dual
filament ramming volumetric speed nc: -1, -1 via fdm_filament_template_direct_dual
filament retract before wipe: nil, nil via fdm_filament_template_direct_dual
filament retract length nc: 14, 14 via fdm_filament_template_direct_dual
filament retract restart extra: nil, nil via fdm_filament_template_direct_dual
filament retract when changing layer: nil, nil via fdm_filament_template_direct_dual
filament retraction distances when cut: 18, 18 overridden
filament retraction minimum travel: nil, nil via fdm_filament_template_direct_dual
filament soluble: 0 inherited
filament wipe: nil, nil via fdm_filament_template_direct_dual
filament wipe distance: nil, nil via fdm_filament_template_direct_dual
filament z hop: nil, nil via fdm_filament_template_direct_dual
filament z hop types: nil, nil via fdm_filament_template_direct_dual
full fan speed layer: 0 inherited
impact strength z: 7.2 inherited
instantiation: true overridden
was false (inherited)
long retractions when ec: 0, 0 overridden
nozzle temperature range high: 270 inherited
nozzle temperature range low: 230 inherited
overhang fan speed: 90 inherited
overhang fan threshold: 10% inherited
override process overhang speed: 0, 0 via fdm_filament_template_direct_dual
reduce fan stop start freq: 1 inherited
required nozzle HRC: 3 inherited
retraction distances when ec: 0, 0 overridden
setting id: GFSG01_01 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 80 inherited
volumetric speed coefficients: 0 0 0 0 0 0, 0 0 0 0 0 0 via fdm_filament_template_direct_dual

Raw resolved JSON

{
  "type": "filament",
  "fan_max_speed": [
    "60"
  ],
  "fan_min_speed": [
    "20"
  ],
  "filament_cost": [
    "24.99"
  ],
  "filament_type": [
    "PETG"
  ],
  "filament_wipe": [
    "nil",
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "70"
  ],
  "filament_z_hop": [
    "nil",
    "nil"
  ],
  "hot_plate_temp": [
    "70"
  ],
  "cool_plate_temp": [
    "0"
  ],
  "filament_vendor": [
    "Bambu Lab"
  ],
  "filament_density": [
    "1.25"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "245",
    "245"
  ],
  "overhang_fan_speed": [
    "90"
  ],
  "filament_flow_ratio": [
    "0.95",
    "0.95"
  ],
  "filament_is_support": [
    "0"
  ],
  "required_nozzle_HRC": [
    "3"
  ],
  "slow_down_min_speed": [
    "10",
    "10"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n{if (bed_temperature[current_extruder] >80)||(bed_temperature_initial_layer[current_extruder] >80)}M106 P3 S255\n{elsif (bed_temperature[current_extruder] >60)||(bed_temperature_initial_layer[current_extruder] >60)}M106 P3 S180\n{endif}\n\n{if activate_air_filtration[current_extruder] && support_air_filtration}\nM106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} \n{endif}"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "8"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "filament_wipe_distance": [
    "nil",
    "nil"
  ],
  "overhang_fan_threshold": [
    "10%"
  ],
  "filament_retraction_speed": [
    "nil",
    "nil"
  ],
  "temperature_vitrification": [
    "80"
  ],
  "filament_retraction_length": [
    "0.2",
    "0.2"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil",
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "70"
  ],
  "filament_retract_before_wipe": [
    "nil",
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "70"
  ],
  "cool_plate_temp_initial_layer": [
    "0"
  ],
  "filament_max_volumetric_speed": [
    "16",
    "16"
  ],
  "filament_retract_restart_extra": [
    "nil",
    "nil"
  ],
  "additional_fan_full_speed_layer": [
    "0"
  ],
  "nozzle_temperature_initial_layer": [
    "250",
    "250"
  ],
  "filament_retraction_minimum_travel": [
    "nil",
    "nil"
  ],
  "close_additional_fan_first_x_layers": [
    "3"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil",
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "230"
  ],
  "nozzle_temperature_range_high": [
    "270"
  ],
  "description": "To get better transparent or translucent results with the corresponding filament, please refer to this wiki: Printing tips for transparent PETG.",
  "filament_id": "GFG01",
  "impact_strength_z": [
    "7.2"
  ],
  "textured_plate_temp": [
    "70"
  ],
  "filament_metal_stickiness": [
    "High"
  ],
  "textured_plate_temp_initial_layer": [
    "70"
  ],
  "filament_flush_temp": [
    "0",
    "0"
  ],
  "filament_z_hop_types": [
    "nil",
    "nil"
  ],
  "filament_bridge_speed": [
    "25",
    "25"
  ],
  "long_retractions_when_ec": [
    "0",
    "0"
  ],
  "filament_extruder_variant": [
    "Direct Drive Standard",
    "Direct Drive High Flow"
  ],
  "filament_retract_length_nc": [
    "14",
    "14"
  ],
  "filament_overhang_1_4_speed": [
    "0",
    "0"
  ],
  "filament_overhang_2_4_speed": [
    "50",
    "50"
  ],
  "filament_overhang_3_4_speed": [
    "30",
    "30"
  ],
  "filament_overhang_4_4_speed": [
    "10",
    "10"
  ],
  "retraction_distances_when_ec": [
    "0",
    "0"
  ],
  "filament_cooling_before_tower": [
    "0",
    "0"
  ],
  "volumetric_speed_coefficients": [
    "0 0 0 0 0 0",
    "0 0 0 0 0 0"
  ],
  "filament_enable_overhang_speed": [
    "1",
    "1"
  ],
  "filament_flush_volumetric_speed": [
    "0",
    "0"
  ],
  "filament_overhang_totally_speed": [
    "10",
    "10"
  ],
  "filament_ramming_travel_time_nc": [
    "0",
    "0"
  ],
  "override_process_overhang_speed": [
    "0",
    "0"
  ],
  "filament_pre_cooling_temperature": [
    "0",
    "0"
  ],
  "filament_ramming_volumetric_speed": [
    "-1",
    "-1"
  ],
  "filament_adaptive_volumetric_speed": [
    "0",
    "0"
  ],
  "filament_long_retractions_when_cut": [
    "1",
    "1"
  ],
  "filament_pre_cooling_temperature_nc": [
    "0",
    "0"
  ],
  "filament_ramming_volumetric_speed_nc": [
    "-1",
    "-1"
  ],
  "filament_retraction_distances_when_cut": [
    "18",
    "18"
  ],
  "setting_id": "GFSG01_01",
  "compatible_printers": [
    "Bambu Lab X1 Carbon 0.8 nozzle",
    "Bambu Lab X1 0.6 nozzle",
    "Bambu Lab X1 0.8 nozzle",
    "Bambu Lab P1P 0.8 nozzle",
    "Bambu Lab P1S 0.8 nozzle",
    "Bambu Lab X1E 0.6 nozzle",
    "Bambu Lab X1E 0.8 nozzle"
  ],
  "filament_ramming_travel_time": [
    "0",
    "0"
  ],
  "name": "Bambu PETG Translucent @BBL X1C 0.8 nozzle"
}

Version history

View full history with diffs →

v2 updated 2026-05-19 04:15
v1 created 2026-05-19 04:02