Generic PET @Elegoo Centauri

Generic · PET · by elegoo-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pet

→

Generic PET @base

→

Generic PET @Elegoo Centauri

Compatible printers (9)

Elegoo Centauri 0.4 nozzle
Elegoo Centauri 0.6 nozzle
Elegoo Centauri 0.8 nozzle
Elegoo Centauri Carbon 0.4 nozzle
Elegoo Centauri Carbon 0.6 nozzle
Elegoo Centauri Carbon 0.8 nozzle
Elegoo Centauri Carbon 2 0.4 nozzle
Elegoo Centauri Carbon 2 0.6 nozzle
Elegoo Centauri Carbon 2 0.8 nozzle

Settings

Basic information

Material variant: PET inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.27 inherited
Cost (/kg): 30 inherited

Print temperature

Nozzle (initial layer) (°C): 270 overridden
was 255 (inherited)
Nozzle (other layers) (°C): 270 overridden
was 255 (inherited)

Cooling

Fan minimum (%): 20 overridden
was 40 (inherited)
Fan maximum (%): 60 overridden
was 90 (inherited)
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 8 overridden
was 30 (inherited)
Slow down if layer below (sec): 4 overridden
was 12 (inherited)
Min speed when slowed (mm/s): 20 inherited

Flow

Flow ratio: 1 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 12 inherited

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	0 inherited	0 inherited
Engineering Plate	70 inherited	70 inherited
High Temp Plate	90 overridden was 70	90 overridden was 70
Textured PEI Plate	90 overridden was 70	90 overridden was 70

Other settings

bed type: Cool Plate inherited
compatible printers: Elegoo Centauri 0.4 nozzle, Elegoo Centauri 0.6 nozzle, Elegoo Centauri 0.8 nozzle, Elegoo Centauri Carbon 0.4 nozzle, Elegoo Centauri Carbon 0.6 nozzle, Elegoo Centauri Carbon 0.8 nozzle, Elegoo Centauri Carbon 2 0.4 nozzle, Elegoo Centauri Carbon 2 0.6 nozzle, Elegoo Centauri Carbon 2 0.8 nozzle overridden
filament id: GPETB00 inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 280 overridden
was 270 (inherited)
nozzle temperature range low: 250 overridden
was 220 (inherited)
overhang fan speed: 90 inherited
overhang fan threshold: 25% overridden
was 10% (inherited)
reduce fan stop start freq: 1 inherited
setting id: GPET00 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 80 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "60"
  ],
  "fan_min_speed": [
    "20"
  ],
  "filament_cost": [
    "30"
  ],
  "filament_type": [
    "PET"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "70"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "90"
  ],
  "cool_plate_temp": [
    "0"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.27"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "270"
  ],
  "overhang_fan_speed": [
    "90"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "textured_plate_temp": [
    "90"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; Filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "4"
  ],
  "fan_cooling_layer_time": [
    "8"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "25%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "80"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "70"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "90"
  ],
  "cool_plate_temp_initial_layer": [
    "0"
  ],
  "filament_max_volumetric_speed": [
    "12"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "270"
  ],
  "textured_plate_temp_initial_layer": [
    "90"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "250"
  ],
  "nozzle_temperature_range_high": [
    "280"
  ],
  "filament_id": "GPETB00",
  "setting_id": "GPET00",
  "compatible_printers": [
    "Elegoo Centauri 0.4 nozzle",
    "Elegoo Centauri 0.6 nozzle",
    "Elegoo Centauri 0.8 nozzle",
    "Elegoo Centauri Carbon 0.4 nozzle",
    "Elegoo Centauri Carbon 0.6 nozzle",
    "Elegoo Centauri Carbon 0.8 nozzle",
    "Elegoo Centauri Carbon 2 0.4 nozzle",
    "Elegoo Centauri Carbon 2 0.6 nozzle",
    "Elegoo Centauri Carbon 2 0.8 nozzle"
  ],
  "name": "Generic PET @Elegoo Centauri"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:37