Generic PA @Elegoo

Generic · PA · by elegoo-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pa

→

Generic PA @base

→

Generic PA @Elegoo

Compatible printers (29)

Elegoo Centauri 0.4 nozzle
Elegoo Centauri 0.6 nozzle
Elegoo Centauri 0.8 nozzle
Elegoo Centauri Carbon 0.4 nozzle
Elegoo Centauri Carbon 0.6 nozzle
Elegoo Centauri Carbon 0.8 nozzle
Elegoo Centauri Carbon 2 0.4 nozzle
Elegoo Centauri Carbon 2 0.6 nozzle
Elegoo Centauri Carbon 2 0.8 nozzle
Elegoo Neptune 4 0.4 nozzle
Elegoo Neptune 4 (0.6 nozzle)
Elegoo Neptune 4 (0.8 nozzle)
Elegoo Neptune 4 1.0 nozzle
Elegoo Neptune 4 Max 0.4 nozzle
Elegoo Neptune 4 Max (0.6 nozzle)
Elegoo Neptune 4 Max (0.8 nozzle)
Elegoo Neptune 4 Max 1.0 nozzle
Elegoo Neptune 4 Plus 0.4 nozzle
Elegoo Neptune 4 Plus (0.6 nozzle)
Elegoo Neptune 4 Plus (0.8 nozzle)
Elegoo Neptune 4 Plus 1.0 nozzle
Elegoo Neptune 4 Pro 0.4 nozzle
Elegoo Neptune 4 Pro (0.6 nozzle)
Elegoo Neptune 4 Pro (0.8 nozzle)
Elegoo Neptune 4 Pro 1.0 nozzle
Elegoo OrangeStorm Giga 0.4 nozzle
Elegoo OrangeStorm Giga 0.6 nozzle
Elegoo OrangeStorm Giga 0.8 nozzle
Elegoo OrangeStorm Giga 1.0 nozzle

Settings

Basic information

Material variant: PA inherited
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.04 inherited
Cost (/kg): 20 inherited

Print temperature

Nozzle (initial layer) (°C): 250 overridden
was 260 (inherited)
Nozzle (other layers) (°C): 250 overridden
was 260 (inherited)

Cooling

Fan minimum (%): 80 overridden
was 40 (inherited)
Fan maximum (%): 100 overridden
was 85 (inherited)
Disable fan for first N layers: 5 overridden
was 3 (inherited)
Full fan if layer below (sec): 60 overridden
was 65 (inherited)
Slow down if layer below (sec): 12 overridden
was 8 (inherited)
Min speed when slowed (mm/s): 10 inherited

Flow

Flow ratio: 0.98 overridden
was 1 (inherited)
Max volumetric speed (mm³/s): 8 inherited

Retraction

Retraction length (mm): 1.0 inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	0 inherited	0 inherited
Engineering Plate	100 inherited	100 inherited
High Temp Plate	100 inherited	100 inherited
Textured PEI Plate	100 inherited	100 inherited

Other settings

activate air filtration: 0 overridden
bed type: Cool Plate inherited
chamber temperatures: 60 inherited
compatible printers: Elegoo Neptune 4 0.4 nozzle, Elegoo Neptune 4 0.6 nozzle, Elegoo Neptune 4 0.8 nozzle, Elegoo Neptune 4 1.0 nozzle, Elegoo Neptune 4 Max 0.4 nozzle, Elegoo Neptune 4 Max 0.6 nozzle, Elegoo Neptune 4 Max 0.8 nozzle, Elegoo Neptune 4 Max 1.0 nozzle, Elegoo Neptune 4 Plus 0.4 nozzle, Elegoo Neptune 4 Plus 0.6 nozzle, Elegoo Neptune 4 Plus 0.8 nozzle, Elegoo Neptune 4 Plus 1.0 nozzle, Elegoo Neptune 4 Pro 0.4 nozzle, Elegoo Neptune 4 Pro 0.6 nozzle, Elegoo Neptune 4 Pro 0.8 nozzle, Elegoo Neptune 4 Pro 1.0 nozzle, Elegoo Centauri 0.4 nozzle, Elegoo Centauri 0.6 nozzle, Elegoo Centauri 0.8 nozzle, Elegoo Centauri Carbon 0.4 nozzle, Elegoo Centauri Carbon 0.6 nozzle, Elegoo Centauri Carbon 0.8 nozzle, Elegoo Centauri Carbon 2 0.4 nozzle, Elegoo Centauri Carbon 2 0.6 nozzle, Elegoo Centauri Carbon 2 0.8 nozzle, Elegoo OrangeStorm Giga 0.4 nozzle, Elegoo OrangeStorm Giga 0.6 nozzle, Elegoo OrangeStorm Giga 0.8 nozzle, Elegoo OrangeStorm Giga 1.0 nozzle overridden
filament id: GPAB00 inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: 0.0 inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 290 overridden
was 280 (inherited)
nozzle temperature range low: 240 inherited
overhang fan speed: 100 overridden
was 95 (inherited)
overhang fan threshold: 0% overridden
was 10% (inherited)
reduce fan stop start freq: 1 overridden
was 0 (inherited)
required nozzle HRC: 3 inherited
setting id: GPA00 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 108 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "80"
  ],
  "filament_cost": [
    "20"
  ],
  "filament_type": [
    "PA"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "100"
  ],
  "filament_z_hop": [
    "0.0"
  ],
  "hot_plate_temp": [
    "100"
  ],
  "cool_plate_temp": [
    "0"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.04"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "250"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "0.98"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "textured_plate_temp": [
    "100"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; Filament gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "12"
  ],
  "fan_cooling_layer_time": [
    "60"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "0%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "108"
  ],
  "filament_retraction_length": [
    "1.0"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "5"
  ],
  "eng_plate_temp_initial_layer": [
    "100"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "100"
  ],
  "cool_plate_temp_initial_layer": [
    "0"
  ],
  "filament_max_volumetric_speed": [
    "8"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "250"
  ],
  "textured_plate_temp_initial_layer": [
    "100"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "240"
  ],
  "nozzle_temperature_range_high": [
    "290"
  ],
  "filament_id": "GPAB00",
  "required_nozzle_HRC": [
    "3"
  ],
  "chamber_temperatures": [
    "60"
  ],
  "setting_id": "GPA00",
  "compatible_printers": [
    "Elegoo Neptune 4 0.4 nozzle",
    "Elegoo Neptune 4 0.6 nozzle",
    "Elegoo Neptune 4 0.8 nozzle",
    "Elegoo Neptune 4 1.0 nozzle",
    "Elegoo Neptune 4 Max 0.4 nozzle",
    "Elegoo Neptune 4 Max 0.6 nozzle",
    "Elegoo Neptune 4 Max 0.8 nozzle",
    "Elegoo Neptune 4 Max 1.0 nozzle",
    "Elegoo Neptune 4 Plus 0.4 nozzle",
    "Elegoo Neptune 4 Plus 0.6 nozzle",
    "Elegoo Neptune 4 Plus 0.8 nozzle",
    "Elegoo Neptune 4 Plus 1.0 nozzle",
    "Elegoo Neptune 4 Pro 0.4 nozzle",
    "Elegoo Neptune 4 Pro 0.6 nozzle",
    "Elegoo Neptune 4 Pro 0.8 nozzle",
    "Elegoo Neptune 4 Pro 1.0 nozzle",
    "Elegoo Centauri 0.4 nozzle",
    "Elegoo Centauri 0.6 nozzle",
    "Elegoo Centauri 0.8 nozzle",
    "Elegoo Centauri Carbon 0.4 nozzle",
    "Elegoo Centauri Carbon 0.6 nozzle",
    "Elegoo Centauri Carbon 0.8 nozzle",
    "Elegoo Centauri Carbon 2 0.4 nozzle",
    "Elegoo Centauri Carbon 2 0.6 nozzle",
    "Elegoo Centauri Carbon 2 0.8 nozzle",
    "Elegoo OrangeStorm Giga 0.4 nozzle",
    "Elegoo OrangeStorm Giga 0.6 nozzle",
    "Elegoo OrangeStorm Giga 0.8 nozzle",
    "Elegoo OrangeStorm Giga 1.0 nozzle"
  ],
  "activate_air_filtration": [
    "0"
  ],
  "name": "Generic PA @Elegoo"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:37