Generic PETG-CF @Elegoo Centauri

Generic · PETG-CF · by elegoo-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Strip G-code from download

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pet

→

Generic PETG @base

→

Generic PETG-CF @Elegoo Centauri

Compatible printers (9)

Elegoo Centauri 0.4 nozzle
Elegoo Centauri 0.6 nozzle
Elegoo Centauri 0.8 nozzle
Elegoo Centauri Carbon 0.4 nozzle
Elegoo Centauri Carbon 0.6 nozzle
Elegoo Centauri Carbon 0.8 nozzle
Elegoo Centauri Carbon 2 0.4 nozzle
Elegoo Centauri Carbon 2 0.6 nozzle
Elegoo Centauri Carbon 2 0.8 nozzle

Settings

Basic information

Material variant: PETG-CF overridden
was PETG (inherited)
Vendor: Generic inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.25 overridden
was 1.27 (inherited)
Cost (/kg): 0 overridden
was 30 (inherited)

Print temperature

Nozzle (initial layer) (°C): 240 overridden
was 255 (inherited)
Nozzle (other layers) (°C): 240 overridden
was 255 (inherited)

Cooling

Fan minimum (%): 20 overridden
was 40 (inherited)
Fan maximum (%): 60 overridden
was 90 (inherited)
Disable fan for first N layers: 3 inherited
Full fan if layer below (sec): 30 overridden
was 30 (inherited)
Slow down if layer below (sec): 6 overridden
was 12 (inherited)
Min speed when slowed (mm/s): 20 inherited

Flow

Flow ratio: 0.95 inherited
Max volumetric speed (mm³/s): 12 overridden
was 12 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	0 overridden was 0	0 overridden was 0
Engineering Plate	70 overridden was 70	70 overridden was 70
High Temp Plate	70 overridden was 70	70 overridden was 70
Textured PEI Plate	70 overridden was 70	70 overridden was 70

Custom G-code

filament_start_gcode inherited

; filament start gcode
{if (bed_temperature[current_extruder] >80)||(bed_temperature_initial_layer[current_extruder] >80)}M106 P3 S255
{elsif (bed_temperature[current_extruder] >60)||(bed_temperature_initial_layer[current_extruder] >60)}M106 P3 S180
{endif}

{if activate_air_filtration[current_extruder] && support_air_filtration}
M106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} 
{endif}

Other settings

bed type: Cool Plate inherited
compatible printers: Elegoo Centauri 0.4 nozzle, Elegoo Centauri 0.6 nozzle, Elegoo Centauri 0.8 nozzle, Elegoo Centauri Carbon 0.4 nozzle, Elegoo Centauri Carbon 0.6 nozzle, Elegoo Centauri Carbon 0.8 nozzle, Elegoo Centauri Carbon 2 0.4 nozzle, Elegoo Centauri Carbon 2 0.6 nozzle, Elegoo Centauri Carbon 2 0.8 nozzle overridden
filament id: GFG99 inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 260 overridden
was 270 (inherited)
nozzle temperature range low: 230 overridden
was 220 (inherited)
overhang fan speed: 100 overridden
was 90 (inherited)
overhang fan threshold: 10% overridden
was 10% (inherited)
reduce fan stop start freq: 1 inherited
required nozzle HRC: 40 overridden
setting id: GPETGCF00 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 70 overridden
was 80 (inherited)

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "60"
  ],
  "fan_min_speed": [
    "20"
  ],
  "filament_cost": [
    "0"
  ],
  "filament_type": [
    "PETG-CF"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "70"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "70"
  ],
  "cool_plate_temp": [
    "0"
  ],
  "filament_vendor": [
    "Generic"
  ],
  "filament_density": [
    "1.25"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "240"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "0.95"
  ],
  "slow_down_min_speed": [
    "20"
  ],
  "textured_plate_temp": [
    "70"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n{if (bed_temperature[current_extruder] >80)||(bed_temperature_initial_layer[current_extruder] >80)}M106 P3 S255\n{elsif (bed_temperature[current_extruder] >60)||(bed_temperature_initial_layer[current_extruder] >60)}M106 P3 S180\n{endif}\n\n{if activate_air_filtration[current_extruder] && support_air_filtration}\nM106 P3 S{during_print_exhaust_fan_speed_num[current_extruder]} \n{endif}"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "6"
  ],
  "fan_cooling_layer_time": [
    "30"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "10%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "70"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "3"
  ],
  "eng_plate_temp_initial_layer": [
    "70"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "70"
  ],
  "cool_plate_temp_initial_layer": [
    "0"
  ],
  "filament_max_volumetric_speed": [
    "12"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "240"
  ],
  "textured_plate_temp_initial_layer": [
    "70"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "nozzle_temperature_range_low": [
    "230"
  ],
  "nozzle_temperature_range_high": [
    "260"
  ],
  "filament_id": "GFG99",
  "setting_id": "GPETGCF00",
  "compatible_printers": [
    "Elegoo Centauri 0.4 nozzle",
    "Elegoo Centauri 0.6 nozzle",
    "Elegoo Centauri 0.8 nozzle",
    "Elegoo Centauri Carbon 0.4 nozzle",
    "Elegoo Centauri Carbon 0.6 nozzle",
    "Elegoo Centauri Carbon 0.8 nozzle",
    "Elegoo Centauri Carbon 2 0.4 nozzle",
    "Elegoo Centauri Carbon 2 0.6 nozzle",
    "Elegoo Centauri Carbon 2 0.8 nozzle"
  ],
  "required_nozzle_HRC": [
    "40"
  ],
  "name": "Generic PETG-CF @Elegoo Centauri"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:37