Elegoo PLA @EN2 Series

Elegoo · PLA · by elegoo-system · 0 downloads

Download for Bambu Studio Download for OrcaSlicer Download for PrusaSlicer

Compare

Inheritance

fdm_filament_common

→

fdm_filament_pla

→

Elegoo PLA @base

→

Elegoo PLA @EN2 Series

Compatible printers (18)

Elegoo Neptune 0.4 nozzle
Elegoo Neptune 0.6 nozzle
Elegoo Neptune 0.8 nozzle
Elegoo Neptune 2 0.4 nozzle
Elegoo Neptune 2 0.6 nozzle
Elegoo Neptune 2 0.8 nozzle
Elegoo Neptune 2D 0.4 nozzle
Elegoo Neptune 2D 0.6 nozzle
Elegoo Neptune 2D 0.8 nozzle
Elegoo Neptune 2S 0.4 nozzle
Elegoo Neptune 2S 0.6 nozzle
Elegoo Neptune 2S 0.8 nozzle
Elegoo Neptune 3 0.4 nozzle
Elegoo Neptune 3 0.6 nozzle
Elegoo Neptune 3 0.8 nozzle
Elegoo Neptune X 0.4 nozzle
Elegoo Neptune X 0.6 nozzle
Elegoo Neptune X 0.8 nozzle

Settings

Basic information

Material variant: PLA inherited
Vendor: Elegoo inherited
Diameter (mm): 1.75 inherited
Density (g/cm³): 1.25 inherited
Cost (/kg): 0 inherited

Print temperature

Nozzle (initial layer) (°C): 210 overridden
was 220 (inherited)
Nozzle (other layers) (°C): 210 overridden
was 220 (inherited)

Cooling

Fan minimum (%): 80 overridden
was 100 (inherited)
Fan maximum (%): 100 inherited
Disable fan for first N layers: 1 inherited
Full fan if layer below (sec): 100 inherited
Slow down if layer below (sec): 5 inherited
Min speed when slowed (mm/s): 10 overridden
was 5 (inherited)

Flow

Flow ratio: 1 inherited
Max volumetric speed (mm³/s): 9 overridden
was 16 (inherited)

Retraction

Retraction length (mm): nil inherited
Retraction speed (mm/s): nil inherited
Deretraction speed (mm/s): nil inherited

Bed temperature

Plate	Initial layer (°C)	Other layers (°C)
Cool Plate	50 inherited	50 inherited
Engineering Plate	50 inherited	50 inherited
High Temp Plate	50 inherited	50 inherited
Textured PEI Plate	50 inherited	50 inherited

Other settings

additional cooling fan speed: 0 inherited
bed type: Cool Plate inherited
compatible printers: Elegoo Neptune 0.4 nozzle, Elegoo Neptune 0.6 nozzle, Elegoo Neptune 0.8 nozzle, Elegoo Neptune 2 0.4 nozzle, Elegoo Neptune 2 0.6 nozzle, Elegoo Neptune 2 0.8 nozzle, Elegoo Neptune 2S 0.4 nozzle, Elegoo Neptune 2S 0.6 nozzle, Elegoo Neptune 2S 0.8 nozzle, Elegoo Neptune 2D 0.4 nozzle, Elegoo Neptune 2D 0.6 nozzle, Elegoo Neptune 2D 0.8 nozzle, Elegoo Neptune X 0.4 nozzle, Elegoo Neptune X 0.6 nozzle, Elegoo Neptune X 0.8 nozzle, Elegoo Neptune 3 0.4 nozzle, Elegoo Neptune 3 0.6 nozzle, Elegoo Neptune 3 0.8 nozzle overridden
filament id: EPLAB00 inherited
filament minimal purge on wipe tower: 15 inherited
filament retract before wipe: nil inherited
filament retract restart extra: nil inherited
filament retract when changing layer: nil inherited
filament retraction minimum travel: nil inherited
filament soluble: 0 inherited
filament wipe: nil inherited
filament wipe distance: nil inherited
filament z hop: nil inherited
filament z hop types: nil inherited
full fan speed layer: 0 inherited
instantiation: true overridden
was false (inherited)
nozzle temperature range high: 230 inherited
nozzle temperature range low: 190 inherited
overhang fan speed: 100 inherited
overhang fan threshold: 75% overridden
was 50% (inherited)
reduce fan stop start freq: 1 inherited
setting id: EPLAEN2 overridden
slow down for layer cooling: 1 inherited
temperature vitrification: 60 inherited

Raw resolved JSON

{
  "type": "filament",
  "bed_type": [
    "Cool Plate"
  ],
  "fan_max_speed": [
    "100"
  ],
  "fan_min_speed": [
    "80"
  ],
  "filament_cost": [
    "0"
  ],
  "filament_type": [
    "PLA"
  ],
  "filament_wipe": [
    "nil"
  ],
  "instantiation": "true",
  "eng_plate_temp": [
    "50"
  ],
  "filament_z_hop": [
    "nil"
  ],
  "hot_plate_temp": [
    "50"
  ],
  "cool_plate_temp": [
    "50"
  ],
  "filament_vendor": [
    "Elegoo"
  ],
  "filament_density": [
    "1.25"
  ],
  "filament_soluble": [
    "0"
  ],
  "filament_diameter": [
    "1.75"
  ],
  "filament_end_gcode": [
    "; filament end gcode \n"
  ],
  "nozzle_temperature": [
    "210"
  ],
  "overhang_fan_speed": [
    "100"
  ],
  "filament_flow_ratio": [
    "1"
  ],
  "slow_down_min_speed": [
    "10"
  ],
  "textured_plate_temp": [
    "50"
  ],
  "filament_settings_id": [
    ""
  ],
  "filament_start_gcode": [
    "; filament start gcode\n"
  ],
  "filament_z_hop_types": [
    "nil"
  ],
  "full_fan_speed_layer": [
    "0"
  ],
  "slow_down_layer_time": [
    "5"
  ],
  "fan_cooling_layer_time": [
    "100"
  ],
  "filament_wipe_distance": [
    "nil"
  ],
  "overhang_fan_threshold": [
    "75%"
  ],
  "filament_retraction_speed": [
    "nil"
  ],
  "temperature_vitrification": [
    "60"
  ],
  "filament_retraction_length": [
    "nil"
  ],
  "reduce_fan_stop_start_freq": [
    "1"
  ],
  "filament_deretraction_speed": [
    "nil"
  ],
  "slow_down_for_layer_cooling": [
    "1"
  ],
  "close_fan_the_first_x_layers": [
    "1"
  ],
  "eng_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retract_before_wipe": [
    "nil"
  ],
  "hot_plate_temp_initial_layer": [
    "50"
  ],
  "cool_plate_temp_initial_layer": [
    "50"
  ],
  "filament_max_volumetric_speed": [
    "9"
  ],
  "filament_retract_restart_extra": [
    "nil"
  ],
  "nozzle_temperature_initial_layer": [
    "210"
  ],
  "textured_plate_temp_initial_layer": [
    "50"
  ],
  "filament_retraction_minimum_travel": [
    "nil"
  ],
  "filament_minimal_purge_on_wipe_tower": [
    "15"
  ],
  "filament_retract_when_changing_layer": [
    "nil"
  ],
  "additional_cooling_fan_speed": [
    "0"
  ],
  "nozzle_temperature_range_low": [
    "190"
  ],
  "nozzle_temperature_range_high": [
    "230"
  ],
  "filament_id": "EPLAB00",
  "setting_id": "EPLAEN2",
  "compatible_printers": [
    "Elegoo Neptune 0.4 nozzle",
    "Elegoo Neptune 0.6 nozzle",
    "Elegoo Neptune 0.8 nozzle",
    "Elegoo Neptune 2 0.4 nozzle",
    "Elegoo Neptune 2 0.6 nozzle",
    "Elegoo Neptune 2 0.8 nozzle",
    "Elegoo Neptune 2S 0.4 nozzle",
    "Elegoo Neptune 2S 0.6 nozzle",
    "Elegoo Neptune 2S 0.8 nozzle",
    "Elegoo Neptune 2D 0.4 nozzle",
    "Elegoo Neptune 2D 0.6 nozzle",
    "Elegoo Neptune 2D 0.8 nozzle",
    "Elegoo Neptune X 0.4 nozzle",
    "Elegoo Neptune X 0.6 nozzle",
    "Elegoo Neptune X 0.8 nozzle",
    "Elegoo Neptune 3 0.4 nozzle",
    "Elegoo Neptune 3 0.6 nozzle",
    "Elegoo Neptune 3 0.8 nozzle"
  ],
  "name": "Elegoo PLA @EN2 Series"
}

Version history

View full history with diffs →

v1 created 2026-05-19 12:35